Panasonic LCD Projector Pt Tw343 Operating Instructions

ENGLISH - 21
Attention
 fDo not block the ventilation ports (intake and exhaust) of the projector.
WARNING
Keep your hands and other objects away from the air exhaust port. fKeep your hand and face away.
 fDo not insert your finger.
 fKeep heat-sensitive articles away.
Heated air from the air exhaust port can cause burns, injury, or deformations.
Note
 fThe remote control can be used within a distance of about 5 m (16'4-13/16") if pointed directly at the remote control signal 
receiver. The...

22 - ENGLISH
Control panel and Indicators
1
2
3
45
6
7
1 Power indicator  
Displays the status of the power.
2 Power  button
Turns the projector on/off. (v standby / b power on)
3 asqw buttons
Used to select the menu items in the menu operation.
4  / q button
Displays the menu screen.
5 Warning indicator 
Indicates the abnormal conditions of the projector.
6  button
Used to correct the keystone. (x page 39)
7  / w button
Displays the input source menu. (x pages 37, 48) 
Used to execute  button when the...

ENGLISH - 23
Attention
 fWhen a LAN cable is directly connected to the projector, the network connection must be made indoors.
Rear terminals
12
3
4
56 78
9 10
11
1213
1  terminal
This is the terminal to output the audio signal input to the 
projector.
2  terminal
This is the terminal to input video signals.
3  terminal
This is the terminal to input RGB, Component (YCBCR/
YPBPR) or S-video signals.
4  terminal
This is the terminal to input RGB signals.
5  terminal
This is the terminal to input HDMI...

24 - ENGLISH
Preparing the remote control
Inserting and Removing batteries
(ii)
(i)
(ii)
(i)
Fig. 1Fig. 2
1) Open the cover. (Fig. 1)
2) Insert batteries and close the cover (Insert the "m" side first.). (Fig. 2)
 fWhen removing the batteries, perform the steps in reverse order.
When using the multiple projectors
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector 
individually using single remote control, if unique ID number is...

ENGLISH - 25
How to use the Interactive light pen
About the Interactive light pen
Power buttonTip with touch sensor
Installing and Removing batteries
(i)
(ii)
1) Rotate the cap of the pen in the direction as shown in Figure 1. 
2) Install batteries in the direction as shown in Figure 2 and rotate the c\
ap of the pen in the reverse 
direction to close. 
 f 
Remove the batteries in the reverse order of installation. 
How to use the pen
While pressing the tip against a hard screen, the LED for infrared ray...

26 - ENGLISH
Chapter 2   Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and 
connections.  

ENGLISH - 27
Setting up
Installation mode
There are four ways to set up the projector. Set the [Display] menu → [Project way] (x page 51) depending on the 
installation location. 
Mounting on the ceiling and projecting forwardSetting on a desk/floor and projecting from rear
(Using the translucent screen)
Menu itemMethodMenu itemMethod
[Project way][Ceiling/Front][Project way][Rear]
Mounting on the ceiling and projecting from rear
(Using the translucent screen)
Setting on a desk/floor and projecting...

28 - ENGLISH
Screen size and throw distance
Refer to the screen size and projection distances to install the projector. Image size and image position can be adjusted in 
accordance with the screen size and screen position.
Projected image
SH
SW
SD
SH
Screen
L
Screen L
SW
H
LProjection distance (m)
SHImage height (m)
SWImage width (m)
HDistance from the center of lens to the image lower end (m)
SDProjected image size (m)
Attention
 fBefore installing, please read “Precautions for use” (x page 14)....

ENGLISH - 29
Adjusting adjustable feet
Lift the front of the projector and press the feet lock latch with your finger to adjust the projection angle up and 
down. Release your finger to lock the adjustable feet.
For slight adjustment, rotate the adjustable feet. 
Rotate the adjustable feet to extend it as shown in the figure, and rotate it in the opposite direction to contract it.
Attention
 fHeated air comes out of the air exhaust port while the lamp is lit. Do not touch the air exhaust port directly...

30 - ENGLISH
Connecting
Before connecting
 fBefore connecting, carefully read the operating instructions for the external device to be connected.
 fTurn off the power switch of the devices before connecting cables.
 fTake note of the following points before connecting the cables. Failure to do so may result in malfunctions.
-  When connecting a cable to a device connected to the projector or the projector itself, touch any nearby metallic objects to eliminate static electricity from your body before...