Panasonic LCD Projector Pt Lx22E Operating Instructions

Setting up
ENGLISH - 21
Getting Started
Adjusting front adjustable foot
Lift the front of the projector and press the foot lock latch on the projector.
Release the foot lock latch to lock the adjustable foot and rotate the adjustable foot to a proper height and tilt.
You can turn the front adjustable foot to extend it. You can turn it in the opposite direction to contract it.
(You can adjust the projection angle vertically.)
Attention
Heated air comes out of the air exhaust port while the lamp is lit. Do...

22 - ENGLISH
Getting Started
Connections
Before connecting to the projector
Read carefully the instruction manual for the device to be connected. z
Turn off the power switch of the devices before connecting cables. z
If any connection cable is not supplied with the device, or if no option\
al cable is available for connection of the  z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the screen to randomly wobble or...

ENGLISH - 23
Basic Operation
Powering ON/OFF
Basic Operation
Picture (2)Picture (3)
Connecting the power cord
Be sure to insert the attached power cord securely to its base to preven\
t it from coming off.
Power cord holder J
A power cord holder is designed to prevent the AC power cord from coming off the projector.
Please insert the power cord into the power cord holder correctly as Pic\
ture (1) shown:
                                                                        \
            Picture (1)...

Powering ON/OFF
24 - ENGLISH
Basic Operation
STANDBY(R)/ON(G) indicator
The  indicator informs you the status of the power. Confirm the status of the 
 indicator before operating the projector.
Indicator statusStatus
No illumination or flashingThe power cord is unplugged.
RED
LitThe power cord is plugged.
The projector is in stand-by mode, after the cooling is completed.
Flashing
The projector cannot be turned on until the normal power-off processing for fan 
cooling is completing and the indicator stops...

Powering ON/OFF
ENGLISH - 25
Basic Operation
Complete peripheral connections (with a 1 ) 
computer, VCR, etc.) before turning on the 
projector.
Connect the projector’s AC power cord into an 2 ) 
AC outlet. The  indicator 
lights red. Open the lens cap.
Press the 3 )  button on the control panel or 
the remote control. The  
indicator lights green and the cooling fans start 
to operate. The preparation display appears on 
the screen and the count down starts.
After the countdown, the input source that...

Powering ON/OFF
26 - ENGLISH
Basic Operation
Enter a PIN code
PIN Code Input Dialog BoxPress ▲▼ to enter a number. Press ► to fix the 
number and move the red frame pointer to the next 
box. The number changes to . If you fixed an 
incorrect number, use the Point ◄ button to move the 
pointer to the number you want to correct, and then 
enter the correct number.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer 
to “Set”. Press the  button...

Powering ON/OFF
ENGLISH - 27
Basic Operation
Press the  button on the control panel or 
the remote control, and Power off? appears on 
the screen.
Press the  button on the control panel or  
the remote control again to turn off the projector. 
The  indicator starts to 
blink red, and the cooling fans keep running. 
At this time, you can unplug the AC power cord 
even if the fans are still running.
When the projector has cooled down enough, the 3 ) 
 indicator stops blinking 
and you can turn on the...

28 - ENGLISH
Basic Operation
Projecting
Check the connections of the peripheral devices and connection of the po\
wer cord (Æpage 23) and switch on the 
power (Æpage 25) to start the projector. Select the image and adjust the state of the image.
Selecting the image
Select an input signal.
The image selected with the , 
, , or  button is 
projected (Æpage 29).
Attention
Images may not be projected properly depending on the  z
connected device and DVD, video tape, etc. to be played. 
Select a system format...

ENGLISH - 29
Basic Operation
Basic operations by using the remote control
Using the AUTO SETUP  function
This function allows you to automatically adjust 
Input search, Auto Keystone correction and Auto PC 
adjustment during signal input from a computer.
 Button
Press the  button on the 
remote control.
Note
For details, see “Setting” of Main menu. ( zÆpage 46)
Switching the input signal
You can switch the input signals to project.
 Buttons
Press (,, 
, or ) button on 
the remote control.
COMPUTER...

Basic operations by using the remote control
30 - ENGLISH
Basic Operation
Note
The white arrows indicate that there is no correction. z
A red arrow indicates the direction of correction. z
An arrow disappears at the maximum correction. z
If you press the  button on the remote  z
control once more while the keystone dialog box is being 
displayed, the keystone adjustment will be canceled 
(Æpage 45).
The adjustable range is limited depending on the input  z
signal.
Using the INFO. button
This function...