Panasonic LCD Projector PT-LW80NTU Operating Instructions

ENGLISH - 41
Settings
WIRELESS menu
In WIRELESS menu, the following items are available.
  NETWORK
  NAME CHANGE
  INPUT PASSWORD
  PASSWORD CHANGE
  NETWORK STANDBY
  WEB CONTROL
  LIVE MODE CUT IN
  STATUS
  INITIALIZE
NOTE:
• See the wireless connecting information in the contents 
of the CD-ROM which is provided with the projector.
• When  INPUT PASSWORD  in SECURITY menu is 
activated, perform the correct password operation to 
initialize the projector via network.
MENURETURN
Remote control Control...

ENGLISH - 42
Maintenance
LAMP and TEMP Indicators
If a problem should occur with the projector, the LAMP and/or  TEMP indicators 
will inform you. Manage the in dicated problems as follow.
1. Confirm the status of all indicators and projector, and switch off the  projector in proper way.
 See “Switching the projector on/off” on page 18.
2. Find out the cause of the problem by status of the LAMP  and/or TEMP 
indicators.
3. Follow the instruction  for each indication below and solve the problem.
4. Turn...

ENGLISH - 43
Maintenance
Care and Replacement
JBefore cleaning the projector
 Switch off the projector and disconnect the power plug from the wall outlet.
  Unplug all the cables from the projector.
J Cleaning the outer sur face of the projector
Wipe off dirt and dust gently with a soft cloth.
 If it is difficult to remove the di rt, soak a cloth with water, wring the cloth well and then wipe the projector. 
Dry off the projector with dry cloth.
  Do not use petroleum benzine, thinner, any alcoholic...

Maintenance
Care and Replacement
ENGLISH - 44
The lamp unit, ET-LAB80 is consumable and you must replace it regularly. It is recommended that a qualified 
technician carry the lamp unit replacement and consult with an Authorized Service Center.
JWhen to replace the Lamp unit
When the lamp is consumed, the brightness may decrea se over time. 3 000 hours of use is the replacing 
timing as rough guided, and that might be shortened by  the usage conditions, characteristics of the lamp unit 
or environmental...

Care and Replacement
ENGLISH - 45
Maintenance
JReplacement procedure
Q Removing and replacing the lamp unit
1. Use a Phillips-head screwdriver to loosen the 2 
lamp unit cover fixing screws on the back of the 
projector until the screws turn freely, and remove 
the lamp unit cover.
2. Use a Phillips-head screwdriver to loosen the 3  lamp unit fixing screws. 3. Pull the used lamp unit gently from the projector.
 
Grip the handle and keep the lamp unit paralleled 
when you remove the lamp.  Some parts of...

ENGLISH - 46
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference page
Power does not turn on.
 The power cord may not be connected securely.
 No electric supply at the wall outlet.
 TEMP  indicator is lit or flashes.
 LAMP indicator is lit or flashes.
 The lamp unit cover has not been securely installed.
 The circuit breakers have tripped. 18
19
42
42
45
-
No picture appears.
 The signal input source may not be connected to a terminal properly.
 The input...

ENGLISH - 47
Appendix
Technical Information
List of compatible signals
Mode
Display 
resolution 
(dots)
*1
*1. The “i” appearing after the resolution indicates an interlaced signal.
Scanning 
frequencyDot clock 
frequency (MHz)Picture 
quality
*2
*2. The following symbols are used  to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processi ng circuit before picture is projected.
B Some loss of data occurs to make projection easier.Te r m i n a l...

Appendix
Technical Information
ENGLISH - 48
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface 
specification, so that the projector ca n be controlled by a personal computer  which is connected to this connecter.
JConnection
J Pin assignments and signal names
J Communication settings
J Basic format
 The projector can not receive any command for 10 seco nds after the lamp is switched on. Wait 10 seconds 
before sending the command.
  If sending...

Technical Information
ENGLISH - 49
Appendix
JCable specifications
(When connected to a personal computer)
JControl commands
You can switch the signals which to output from the  COMPUTER1 OUT terminal by pressing the computer key 
command. The key commands are depend on the manufactures . If you select the computer terminals which has no 
signals while the  INPUT GUIDE is set to DETAILED , the computer connection  guidance will be displayed. 
CommandControl contentsRemarks
PON Power onIn standby mode, all...

Appendix
Technical Information
ENGLISH - 50
Specifications
Power supplyAC 100 - 240 V 50 Hz/60 Hz
Power consumption300 W
During standby (when fan is stopped): 4 W
Amps
3.5 A - 1.2 A
LCD panel
Panel size (diagonal)0.59 type
Aspect ratio16 : 10
Display method3 transparent LCD panels (RGB)
Drive methodActive matrix method
Pixels1 024 000 (1 280 x 800) x 3 panels
Lens Manual zoom (1.2x)/Manual focus
F 1.65 - 1.93, f 18.53 mm - 22.18 mm
Optical axis
9 :1 fixed
LampUHM lamp (220 W)
Luminosity*1
*1....