Panasonic LCD Projector Pt Lw362 Operating Instructions

							ENGLISH - 81
Network connection
This projector has network function that allows the following by connecting a computer. The wireless module (Model No.: ET-WML100) of the optional accessories is required if the wireless LAN is connected.
 fWEB control 
By accessing to the projector from a computer, you can perform setting, adjustment, status display, etc. of the projector. 
Refer to “Web control function” (x page 86) for details. fMulti Projector Monitoring & Control software 
This software allows you to monitor and control multiple projectors connected to the LAN. For details about “Multi Projector Monitoring & Control software”, please refer to the Operating Instructions which is included in the CD-ROM of accessories. fPresenter Light By using still image transfer application software “Presenter Light” that supports Windows computers, you can transfer 
images and audio to the projector via the wired LAN/wireless LAN. For more details, please refer to the Operating 
Instructions which is included in the CD-ROM of accessories.  fVueMagic By using still image transfer application software “VueMagic”, you can transfer images to the projector when iPad / 
iPhone / iPod touch or Android terminals are connected to this projector through the wireless L\
AN. Refer to “VueMagic” 
(x page 85) for details. fPJLink By using PJLink protocol, you can send inquiries about the operations or status of the projector from a computer. Refer to 
“Using the PJLink protocol” (x page 102) for details.
When connecting via wired LAN
Connection example
LAN cable (straight)LAN cable (straight)
Hub
Computer
Projector
 rName and function of  terminal123
1 LAN LINK/ACT lamp (yellow) Lights on when connected. Blinks when transmitting/receiving data.
2  terminal (10BASE-T/100BASE-TX)Used to connect LAN cable here.
3 LAN 10/100 lamp (green)Lights on when connected to the 100BASE-TX.
Attention
 fWhen a LAN cable is directly connected to the projector, the network connection must be made indoors.
 f 
When connecting cables to both the  terminal and the  terminal, it may be difficult to remove 
the LAN cable which is connected to the  terminal. When removing the LAN cable from the  terminal, remove a 
cable connected to the  terminal or the  terminal beforehand.
Note
 fA LAN cable is required to use the wired LAN function.
 fUse shielded LAN cable (STP cable) that is compatible with category 5 or above.
 fUse a LAN cable with length of 100 m or shorter.
Chapter 5   Operation of Function - Network connection  
						

							82 - ENGLISH
Projector settings
1) Use the LAN cable (Straight) to connect the projector with computer.
2) Turn on the projector.
3) Set the [Expand] menu → [Network] → [Network setting]. 
 fFor details, refer to the [Expand] menu → [Network] (x page 69).
Note
 fPlease confirm with your network administrator before you connect to an existing network.
 fThe following settings are set before the projector leaves the factory.
[DHCP]Off
[IP address]192.168.1.100
[Subnet]255.255.255.0
[Gateway]192.168.1.1
[DNS]192.168.1.1
Computer setting
Connection can be made with wired LAN. However, confirm to your system administrator on network settings before chang-ing any settings.
1) Turn on the computer.
2) Make the network setting according to your system administrator.
 fIf the projector settings are the default settings, the computer can be \
used with the following network settings.
[IP address]192.168.1.101
[Subnet]255.255.255.0
[Gateway]192.168.1.1
When connecting via wireless LAN
The wireless module (Model No.: ET-WML100) of the optional accessories is required if you want to use the network function through the wireless LAN.
 fOnly one projector can be connected with the wireless LAN.
Connection example
IEEE802.11b/g/n
Wireless module of optional accessories
(Model No.: ET-WML100)
Preparation and confirmation of the projector
1) Turn on the projector.
2) Insert the wireless module (Model No.: ET-WML100) of optional accessories firmly into the  terminal.
LED
Wireless module of optional accessories
(Model No.: ET-WML100)
Chapter 5   Operation of Function - Network connection  
						

							ENGLISH - 83
3) Press the  button on the remote control to switch to 
[Network] input.
 fThe network input idle screen is displayed. The login password (a four-digit number that is automatically generated), 
projector name: PROJECTOR (fixed), IP address (Wireless LAN) and IP address (Wired LAN) will be displayed in the 
idle screen.
 fPress the  button on the control panel and the input source screen is displayed, then press as to 
select [Network].
LOGIN PASSWORD :   5678
PROJECTOR NAME :   PROJECTOR
IP ADDRESS(WIRELESS) :   172.28.120.1
IP ADDRESS(WIRED) :   192.168.1.100
 
Network input idle screen
 
f LOGIN PASSWORD
 
f PROJECTOR NAME
 
f IP ADDRESS(WIRELESS)
 
f IP ADDRESS(WIRED) 
Attention
 fPlease do not move or transport the projector while the wireless module \
is attached. Doing so maybe cause the wireless 
module to be damaged.
 fThe blue LED of the wireless module will be off when the projector is in standby mode, it will light when the power is\
 turned 
on and it will blink during wireless communicating. 
Please do not remove the wireless module while the LED is blinking.
 fWhen executing an invalid operation during network input, the icon  that indicates the key operation is invalid will be 
displayed. In this case, press the  button and execute each function from the menu operation.
Note
 fThe projector name is fixed as “PROJECTOR” and cannot be changed. 
 fWireless LAN and wired LAN cannot be used in the same segment.
 fThe settings of the wireless module are as follows: 
[SSID]NetworkDisplay
[Channel]1
[IP address]172.28.120.1
[Subnet]255.255.255.0
[Gateway]0.0.0.0
[Access point Encryption]None
Computer setting
1) Turn on the computer.
2) Make the network setting according to your system administrator.
 fPlease make the network settings for the computer and the projector acco\
rding to your system administrator.
3) Connect to the network that has been set in the projector.
 fIf you use a computer, click on the task tray  (bottom right of the computer), then select the same name as the [SSID] that has been set in the projector.
 fPlease confirm [SSID] in the [Expand] menu → [Network] → [Network information] of this projector .
Note
 fIf you use any wireless LAN connection utility that meets the OS standard, follow the operation instruction of the utility to 
connect it.
Chapter 5   Operation of Function - Network connection  
						

							84 - ENGLISH
About Presenter Light
(The wireless module (Model No.: ET-WML100) of the optional accessories is required if the wireless LAN is connected.)By using still image transfer application software “Presenter Light” that supports Windows computers, you can transfer im-ages and audio to the projector via the wired LAN/wireless LAN. 
Download the “Presenter Light” to your computer
1) Activate the Web browser in the personal computer.
2)  Enter the IP address set by the projector into the URL input field of the web browser.
 fThe [Network Display System] screen is displayed.
3) Click [Download].
 fThe download screen of “Presenter Light” is displayed.
4) Click [Download].
 fThe download confirmation screen of the executable file “Presenter Light.exe” is displayed.
5) Save “Presenter Light.exe” on the computer desktop.
 fThis software is used as the executable file format. It cannot be installed in the computer .
 fExecute this file when using the software. Please save this software or make a shortcut for convenient use.
Note
 fFor more details about how to use the software “Presenter Light”, please refer to the operating instructions of “Presenter 
Light Software” of the supplied CD-ROM.
 fDownload the latest versions of “Presenter Light” software from the following URL. 
http://panasonic.net/avc/projector/software/
Chapter 5   Operation of Function - About Presenter Light  
						

							ENGLISH - 85
About VueMagic
(The wireless module (Model No.: ET-WML100) of the optional accessories is required if the wireless LAN is connected.)By using still image transfer application software “VueMagic”, you can transfer images to the projector when iPad /  iPhone / iPod touch or Android terminals are connected to this projector through the wireless LAN.
Connecting with the VueMagic compatible device
1) Check the SSID set in the projector.
 fCheck the [SSID] in the [Expand] menu → [Network] → [Network information].
2) Choose the SSID of this projector on the wireless LAN setting screen of \
the connected device, and 
then connect the wireless.
3) Press the  button on the remote control to select 
[Network]. 
 fSwitch to the network input.
 fPress the  button on the control panel and select the input\
 source in the Input menu.
 fCheck the login password (a four-digit number that is automatically generated) and the IP address (wireless LAN) which 
are displayed on the Network idle screen.
4) Start the VueMagic mobile presenter application of the correspondent VueMagic devices.
5) Choose the model No. of this projector in the projector list. 
 fThe connection confirmation screen is displayed.
6) Choose the display position.
 fThe password entry screen is displayed.
7) Enter the login password and click [OK].
 fThe connected device screen is projected on the screen.
Note
 fWhen connecting to the iOS device or Android device, you must install the dedicated application “VueMagic” to the device. 
For detailed information, refer to the following web site. (Only in English.) 
URL http://vuemagic.pixelworks.com
Disconnecting with the VueMagic compatible device
Close the VueMagic mobile presenter application of the device by clicking the .
Chapter 5   Operation of Function - About VueMagic  
						

							86 - ENGLISH
Web control function
(The wireless module (Model No.: ET-WML100) of the optional accessories is required if the wireless LAN is connected.)Using Web control functions, you can perform the following operations from a computer.
 fSetting and adjustment of the projector
 fDisplaying projector status
 fSetting of E-mail message sending
Computer that can be used for setting
A web browser is required to use the web control function. Confirm that your web browser can be used beforehand.
OSCompatible web browser
WindowsInternet Explorer 7.0/8.0/9.0/10.0/11.0
Mac OSSafari 4.0/5.0/6.0/7.0
Note
 fCommunication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used 
beforehand.
Accessing from the web browser
1) Activate the Web browser in the personal computer.
2)  Enter the IP address set by the projector into the URL input field of the web browser. 
 fThe [Network Display System] screen is displayed.
3) Click [Login ] and enter the password in the [Password] column.
 fThe factory default setting of the user name is “admin” (fixed) and the password is “admin”.
4) Click [Login ].
 fThe [System Status] page is displayed.
Note
 fYou can click the upper right corner of the web browser screen to select the display language (Only for English, Japanese, 
Traditional Chinese and Simplified Chinese).
 fDo not perform setting or control simultaneously by starting up multiple\
 web browsers. Do not set or control the projector 
from multiple computers.
 fChange the password first. (eight characters in single byte) (x page 88)
 fIf the screen for the web control is not displayed, consult your network\
 administrator.
Chapter 5   Operation of Function - Web control function  
						

							ENGLISH - 87
Description of each item
1 [Logout]Exit the web connection screen by clicking this item.
2 [System Status]The [System Status] page is displayed by clicking this 
item.
3 [General Setup]The [General Setup] page is displayed by clicking this item.
4 [Picture Setup]The [Picture Setup] page is displayed by clicking this item.
5 [Image Setup]The [Image Setup] page is displayed by clicking this item.
6 [Alert Setup]
The [Alert Setup] page is displayed by clicking this item.
7 [Mail Setup]The [Mail Setup] page is displayed by clicking this item.
8 [Network Setup]The [Network Setup] page is displayed by clicking this item.
[System status] page
Display the status of the projector for the following items.
1 [Model Name]Displays the model No. of the projector.
2 [Versions]Displays the version of the firmware of the projector.
3 [LAN Status]Displays the connection status of the LAN.
4 [Wireless Status]Displays the connection status of the wireless LAN.
Chapter 5   Operation of Function - Web control function  
						

							88 - ENGLISH
[General Setup] page
[Change Password for Webpage] is displayed.
1 [Enter Old password]Enters the configured password.
2 [Enter New password]Enters the new password.
3 [Confirm New password]Enters the desired new password again for confirmation.
4 [Apply]Updates the settings.
5 [Power]Turns on/off the power.  
6 [Source Select]Switches the input source of the projector.
[Picture Setup] page
1 [Brightness]Adjusts the brightness of the projected image.
2 [Contrast]Adjusts the contrast of the projected image.
3 [Sharpness]Adjusts the sharpness of the projected image.
4 [Color]Adjusts the color saturation of the projected image.
5 [Tint]Adjusts the skin tone of the projected image.
6 [Color temperature]Adjusts the color temperature of the projected image.
Chapter 5   Operation of Function - Web control function  
						

							ENGLISH - 89
[Image Setup] page
1 [Aspect]Switches the aspect of the projected image.
2 [Fine sync]Adjusts the fine sync of the projected image.
3 [H Position]Adjusts the horizontal position of the projected image.
4 [V Position]Adjusts the vertical position of the projected image.
5 [H.Size]
Adjusts the total number of dots of the projected 
image.
6 [Freeze]Switches the freeze function between on and off.
7 [Auto PC adj.]Executes the Auto PC adj. function.
8 [V Keystone]Corrects the keystone in vertical direction.
9 [H Keystone]Corrects the keystone in horizontal direction.
10 [Curved correction]Corrects the pincushion or barrel of the projected image.
11 [Corner correction]Corrects the four corners of the projected image.
Chapter 5   Operation of Function - Web control function  
						

							90 - ENGLISH
[Alert Setup] page
Set the contents of the E-mail to inform the abnormality of the projecto\
r.
1 [Alert Type]Selects the alert type.
2 [Alert Mail Notification]Checks the alert E-mail when transmitting.
3 [Mail Subject]
Enters the subject of the E-mail. (Up to 100 characters in single byte)
4 [Mail Content]Enters the content of E-mail which is associated with the selected [Alert Type] and then clicks [Apply]. (Up to 255 characters in single byte)
5 [Apply]Clicks [Apply] to save the contents which are entered in [Mail Subject] and [Mail Content].
Note
 f[Mail Subject] /[Mail Content] is not supported with the double-byte characters (e.g. Korean, Chinese and Japanese).
[Mail Setup] page
1 [Mail Server]Enters the IP address of SMTP server.  (Up to 39 characters in single byte)
2 [User Name]Enters the user name.  (Up to 19 characters in single byte)
3 [Password]Enters the password.  (Up to 19 characters in single byte)
4 [To]Enters the recipients of the E-mail. If you want to send E-mail to some recipients, please separate them by using semicolon (;). (Up to 299 characters in single byte)
5 [Test Mail]Clicks [Test Mail] to send the test E-mail.
6 [Apply]Clicks [Apply] to save the content after entering each item.
Note
 fIf the server is not compatible with the login authentication of the adv\
anced SMTP, the e-mail function is disable. 
 fIf the server is not compatible with the advanced SMTP, [User Name] is required, but [Password] is not required.
 fIf the test E-mail is not sent, make sure that each item is set correctl\
y.
Chapter 5   Operation of Function - Web control function