Panasonic LCD Projector Pt Lw362 Operating Instructions

							ENGLISH - 51
OrientationOperationAdjustment
Horizontal (left and right) adjustment.
Press the a button.The image position moves to the right.
Press the s button.The image position moves to the left.
Note
 f[H Position] is not available while the image is expanded in the digital zoom function.
[V Position]
(Only for computer signals input)
Move the image position vertically if the image position projected on th\
e screen is shifted even when the relative position of the 
projector and the screen is installed correctly.
1) Press as to select [V Position].
2) Press the  button.
3) Press as to adjust the vertical image position.
OrientationOperationAdjustment
Vertical (up and down) adjustment.
Press the a button.The image position moves up.
Press the s button.The image position moves down.
Note
 f[V Position] is not available while the image is expanded in the digital zoom function.
[H.Size]
(Only for computer signals input)
Use this function to adjust and minimize the effect of interference caused by projection of patterns consisting of vertical stripes.
The projection of the vertical striped pattern may cause cyclic patterns (noise). Adjust so that the amount of interference is at a 
minimum.
1) Press as to select [H.Size].
2) Press the  button.
3) Press as to adjust the level.
 fThe adjustment values are -15 to +15.
Attention
 fSet it before adjusting [Fine sync].
[Aspect]
Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
1) Press as to select [Aspect]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Normal]Projects the image at the maximum size while maintaining the aspect ratio of the input signal.
[Wide]Projects the image at 16:9 aspect ratio.
Note
 fWhen the Memory Viewer, the USB Display or the Network input is selected, [Aspect] cannot be selected.
Chapter 4   Settings - [Display] menu  
						

							52 - ENGLISH
[Project way]
Set the projection method in accordance with the installation status of \
the projector.
Change the projection method if the screen display is upside down or inverted.
1) Press as to select [Project way]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Front]When installing the projector on the desk, etc. in front of the screen.
[Rear]When installing the projector on the desk, etc. behind the screen (with a translucent screen).
[Ceiling/Front]When installing the projector in front of the screen by using the Ceiling Mount Bracket for 
Projectors (optional).
[Ceiling/Rear]When installing the projector behind the screen (with a translucent screen) by using the Ceiling 
Mount Bracket for Projectors (optional).
[Menu position]
Set the position of the menu screen (OSD).
1) Press as to select [Menu position]. 
2) Press the  button.
3) Press as to change the menu position. 
 fThe items will switch each time you press the button. 
[Upper left] → [Upper right] → [Center] → [Lower left] →[Lower right] → [Upper left] →...
[Background display]
Select the background screen when no input signal is detected.
1) Press as to select [Background display]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Blue]Displays the entire projection area in blue.
[Black]Displays the entire projection area in black.
[System]
Set it to match the resolution of the computer input signals. Set the co\
lor system of Video/S-video signals. 
1) Press as to select [System]. 
2) Press the  button.
 fThe [System] screen is displayed.
3) Press as to select the desired system.
 fThe items will switch each time you press the button.
Input sourceModeDescription
for RGB signal
[1024 x 768, 60Hz], etc Displays the name of the correspond signal.
[Auto]
When there is no input signal compatible with the signal from a connected 
computer on the projector, the Auto PC adj. function works and [Auto] 
is displayed on the system. If images are not being correctly projected,\
 
manually adjust the settings to suit your computer.
for Video/S-video 
signal
[Auto]The projector automatically selects the color system of the input signal\
.
Sets [PAL-M] manually.
[PAL] / [SECAM] / 
[NTSC] / [NTSC443] /  
[PAL-M] / [PAL-N] / 
[PAL60]
Sets the color system manually when the image is not displayed correctly\
 
in [Auto].
4) Press the  button.
Chapter 4   Settings - [Display] menu  
						

							ENGLISH - 53
[Color adjust] menu
On the menu screen, select [Color adjust] from the main menu, and select\
 an item from the sub-menu.Refer to “Navigating through the menu” (x page 45) for the operation of the menu screen.
 fAfter selecting the item, press as to set.
[Image mode]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [Image mode]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Dynamic]The light output is maximized for use in bright areas.
[Standard]The picture becomes suitable for moving images in general.
[Cinema]The picture becomes suitable for movie sources.
[Blackboard 
(Green)]The picture becomes suitable for projecting on a black board (green board) such as classroom.
[Colorboard]
The picture becomes suitable for projecting on a color board. To select [Colorboard], press the 
 button, the [Colorboard] screen is displayed. To select [Red], [Blue], [Green] or [Yellow], 
and press the  button.
[User image]The picture quality is displayed after the manual adjustment of [Color adjust].
4) Press the  button.
[Contrast]
You can adjust the contrast of the colors.
1) Press as to select [Contrast].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Brightens the screen and makes the color deeper.0 ~ +63Press the s button.Darkens the screen and makes the color lighter.
Attention
 fAdjust [Brightness] first when you need to adjust [Brightness] and [Contrast].
[Brightness]
You can adjust the dark (black) part of the projected image.
1) Press as to select [Brightness].
2) Press the  button.
3) Press as to adjust the level.
Chapter 4   Settings - [Color adjust] menu  
						

							54 - ENGLISH
OperationAdjustmentAdjustment range
Press the a button.Increases the brightness of the dark (black) parts of the screen.0 ~ +63Press the s button.Reduces the brightness of the dark (black) parts of the screen.
[Color]
(Only for Video signals, S-video signals and Component signals) 
You can adjust the color saturation of the projected image.
1) Press as to select [Color].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Deepens colors.0 ~ +63Press the s button.Weakens colors.
[Tint]
(Only for Component signals and NTSC/NTSC4.43/PAL60 signals when input Video or S-video signals)
You can adjust the skin tone in the projected image.
1) Press as to select [Tint].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Adjusts skin tone toward greenish color.0 ~ +63Press the s button.Adjusts skin tone toward reddish purple.
[Color temp.]
(Only for computer signals and HDMI signals)
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
1) Press as to select [Color temp.].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[High]Becomes a bluish image at [High]. Becomes a reddish image at [Low]. Selects the suitable natural 
color.[Mid]
[Low]
[Red] / [Green] / [Blue]
You can adjust the white balance.
1) Press as to select [Red] / [Green] / [Blue].
2) Press the  button.
3) Press as to adjust the level.
MenuOperationAdjustmentAdjustment range
[Red]Press the a button.Deepen red tone.0 ~ +63Press the s button.Lighten red tone.
[Green]Press the a button.Deepen green tone.0 ~ +63Press the s button.Lighten green tone.
Chapter 4   Settings - [Color adjust] menu  
						

							ENGLISH - 55
[Blue]Press the a button.Deepen blue tone.0 ~ +63Press the s button.Lighten blue tone.
[Sharpness]
You can adjust the sharpness of the projected image.
1) Press as to select [Sharpness].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Contours become sharper.0 ~ +15Press the s button.Contours become softer.
[Daylight View]
The Daylight View Lite function improves the vividness of the image even if it is proj\
ected under a bright light.
1) Press as to select [Daylight View].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 43)
[On]Enables Daylight View Lite function.
[Off]Disables Daylight View Lite function.
Chapter 4   Settings - [Color adjust] menu  
						

							56 - ENGLISH
[Setting] menu
On the menu screen, select [Setting] from the main menu, and select an i\
tem from the sub-menu.Refer to “Navigating through the menu” (x page 45) for the operation of the menu screen.
 fAfter selecting the item, press as to set.MEMORY VIEWER/
USB DISPLAY
ASPECTINFO.
IMAGE LAMP
DAYLIGHT VIEW
COMPUTER 1 COMPUTER 2
VIDEO
ENTER
MENU
KEYSTONE
FREEZE AV MUTE P-TIMER
D.ZOOMVOLUME
MUTE
[On start]
Set the method of start up when the power cord plugged into the  AC outlet.
1) Press as to select [On start].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]Starts up in the standby mode.
[On]Starts the projection immediately.
Note
 fWhen you do not turn off the projector in procedure of “Powering Off the Projector” (x page 37), the On start function will 
not work properly.
[Standby mode]
Set the power consumption during standby. Change the setting whether or not use the network function.
1) Press as to select [Standby mode].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Eco]Restricts some functions in the standby mode to reduce power consumption\
.
[Normal]Does not restrict network function and serial communication function eve\
n in the standby mode.
Note
 fIf [Standby mode] is set to [Eco], you cannot use network functions and some RS-232C commands.
[High land]
Change the setting according to the altitude in which you use the projector .
1) Press as to select [High land].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]When using the projector in the elevation of below 1 400 m (4 593').
[On 1]When using the projector in the elevation of above 1 400 m (4 593') and below 2 700 m (8 858').
[On 2]When using the projector in the elevation of above 2 700 m (8 858') and below 3 000 m (9 843').
Chapter 4   Settings - [Setting] menu  
						

							ENGLISH - 57
Note
 fIt is set to [Off] when using the projector in the elevation of below 1 400 m (4 593'). It is set to [On 1] when using the projector in the elevation of above 1 400 m (4 593') and below 2 700 m (8 858'). It is set to [On 2] when using the projector in the elevation of above 2 700 m (8 858') and below 3 000 m (9 843'). Failure to do so may shorten the life of the internal parts and result in malfunctions. fDo not set the projector in the elevation of 3 000 m (9 843') or above, otherwise it may shorten the life of the internal parts and result in malfunctions. fWhen it is set to [On 1] or [On 2], the fan noise becomes louder and fan speed increases. 
[Lamp control]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [Lamp control].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 41)
[  (Normal)]Select when high luminance is required.
[  (Eco 1)]Select when high luminance is not required.
[  (Eco 2)]Select when lower luminance than [  (Eco 1)] is required.
Note
 fSet it to [  (Eco 2)] rather than [  (Eco 1)], set it to [  (Eco 1)] rather than [  (Normal)], when you want to reduce 
power consumption, extend the life of lamp and reduce operation noise.
[Cooling fast]
Switch the cooling fan' speed when the power is turned off and shorten the cooling time of the cooling fan.
1) Press as to select [Cooling fast].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Normal]Use this setting normally.
[60 Sec]Use this setting when short cooling period of time is required.
[0 Sec]The cooling fans stop immediately after power-off.
Note
 fWhen it is set to [0 Sec], you cannot restart the projector immediately after the power-off. The lamp remains high temperature and needs to be cooled, so it sometimes takes longer time th\
an usual for the lamp to light up again.  fWhen it is set to [60 Sec], the cooling fans' speed is faster and the motor noise is louder than [Normal] setting after the power-off.
[Closed caption]
(Only for NTSC input)
Set the closed caption.
1) Press as to select [Closed caption].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]Closed caption is not displayed.
[CC1]Displays CC1 data.
[CC2]Displays CC2 data.
[CC3]Displays CC3 data.
[CC4]Displays CC4 data.
Chapter 4   Settings - [Setting] menu  
						

							58 - ENGLISH
Note
 fClosed caption is a function that displays text information of video signals mainly used in North America. Captions may not 
be displayed depending on the connected devices or contents being played\
 back. f[Closed caption] can only be selected if an NTSC signal is input. fIf [Closed caption] is set to the item except for [Off], the brightness of image may be changed according to the external devices or the used content of the closed caption corresponding connecti\
on. fClosed captions are not displayed when the menu screen is displayed.
[Key lock]
Enable/disable the button operations on the control panel and the remote\
 control.
1) Press as to select [Key lock].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[  (Off)]Enables the button operations on the control panel or the remote control\
.
[  (Projector)]Disables the button operations on the control panel.
[  (Remote control)]Disables the button operations on the remote control.
[Iris]
Aperture correction and signal compensation are performed automatically \
based on the image to result in an image of optimum contrast.
1) Press as to select [Iris].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Corrects the aperture.
[Off]No aperture correction.
[Sound]
You can perform more detailed setting for Audio.
Adjusting the volume
1) Press as to select [Sound].
2) Press the  button.
 fThe [Sound] screen is displayed.
3) Press as to select [Volume].
4) Press the  button.
5) Press as to adjust the level.
 fYou can also press the  button on the remote control. (x page 42)
OperationAdjustmentRange
Press the a button.Turns up the volume.0 ~ +25Press the s button.Turns down the volume.
Setting the mute
1) Press as to select [Sound].
2) Press the  button.
 fThe [Sound] screen is displayed.
3) Press as to select [Mute].
Chapter 4   Settings - [Setting] menu  
						

							ENGLISH - 59
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 42)
[On]Audio is not output.
[Off]Audio is output.
[HDMI Setup]
Switch the setting when the external equipment is connected to the  terminal of the projector and the image is not 
projected correctly. Or switch the setting of the audio input.
[Image]
1) Press as to select [HDMI Setup].
2) Press the  button.
 fThe [HDMI Setup] screen is displayed.
3) Press as to select [Image].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[Auto]Set the signal level automatically.
[64-940]Select when the HDMI terminal of an external device (such as a blu-ray player) is connected to the 
 terminal.
[0-1023]
Select when the DVI-D terminal output of an external device (such as a computer) is connected 
to the  terminal via a conversion cable or similar cable. Selec\
t also when the HDMI 
terminal output of a computer or other device is connected to the  terminal.
Note
 fThe optimal setting varies depending on the output setting of the connected external device. Refer to the operation 
instruction of the external device regarding the output of the external device.
[Sound]
1) Press as to select [HDMI setup].
2) Press the  button.
 fThe [HDMI setup] screen is displayed.
3) Press as to select [Sound].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[HDMI]When HDMI input is selected, the sound of HDMI will be output.
[Computer]When HDMI input is selected, the sound which is input to the  terminal will be 
output.
Chapter 4   Settings - [Setting] menu  
						

							60 - ENGLISH
[Expand] menu
On the menu screen, select [Expand] from the main menu, and select an it\
em from the sub-menu.Refer to “Navigating through the menu” (x page 45) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[Language]
You can switch the language of the on-screen display.
1) Press as to select [Language].
2) Press the  button.
 fThe [Language] screen is displayed. (It is displayed in 23 languages with three pages.)
3) Press as to switch the language.
 fThe languages will switch each time you press the button.
4) Press the  button.
 fVarious menus, settings, adjustment screens, control button names, etc., \
are displayed in the selected language.
 fThe language can be changed to English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Finnish, 
Norwegian, Danish, Polish, Hungarian, Czech, Russian, Turkish, Arabic, Kazakh, Vietnamese, Chinese, Korean, 
Japanese and Thai.
Note
 fThe on-screen display language of the projector is set to English by default and when [Expand] → [Factory default] is 
executed (x page 71).
[Auto setup]
Press the  button on the remote control to set the automatic operations of the Input search function, Auto PC 
adj. function and the Auto keystone function.
1) Press as to select [Auto setup].
2) Press the  button.
 fThe [Auto setup] screen is displayed.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
Chapter 4   Settings - [Expand] menu