Panasonic LCD Projector Pt Lw362 Operating Instructions

ENGLISH - 61
[Input search]This function is used to detect the signals and project the automatic in\
put signals automatically.
[Auto PC adj.]This function is used to adjust [Fine sync], [H position], [V position] and [H.Size] automatically 
when input the analog computer signal.
[Auto keystone]This function is used to correct the vertical keystone of the projected \
image automatically.
[Input search]
This function is used to detect the signals and project the automatic in\
put signals automatically.
1)...

62 - ENGLISH
[Keystone]
You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted.
1) Press as to select [Keystone].
2) Press the  button.
 fThe [Keystone] screen is displayed.
3) Press as to select one item.
[Keystone]Sets whether or not to keep the keystone correction after turn off the projector or plug out 
the power cord.
[H/V Keystone]Adjusts when the horizontal or vertical trapezoid of the projected image is distorted.
[Corner...

ENGLISH - 63
Vertical
Press the a button.Adjusts the upper of the keystone.
Press the s button.Adjusts the bottom of the keystone.
Note
 fThe white arrows indicate that there is no correction.
 fA red arrow indicates the direction of correction.
 fAn arrow disappears at the maximum correction.
[Corner correction]
1) Press as to select [Keystone].
2) Press the  button.
 fThe [Keystone] screen is displayed.
3) Press as to select [Corner correction].
4) Press the  button.
 fThe Corner correction arrows are...

64 - ENGLISH
ItemsOperationAdjustment
[Curved correction X Offset]
Press the w button.
Used to correct the right side vertical lines. Extend the top and bottom while  keeping the center part as it is.
Press the q button.
Used to correct the left side vertical lines. Extend the top and bottom while  keeping the center part as it is.
Press the a button.
Used to correct the both sides of the vertical lines. Extend the lower corners while keeping the center part and the upper part as they are.
Press the s...

ENGLISH - 65
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Logo select]Set the logo display when the projector start-up.
[Capture]The projected image is captured as a still image. The captured image will be displayed as the 
startup logo when [Logo select] is set to [User].
[Logo PIN code 
lock]
Set and change the Logo PIN code, and prevents an unauthorized person from changing the PIN 
code.
[Logo PIN code 
change]Change the [Logo PIN code].
[Logo select]
Set...

66 - ENGLISH
4) Press the  button.
 fThe [Logo PIN code] input screen is displayed.
5) Press the  button.
6) Enter the Logo PIN code you have set according to the steps in "Enter a \
Logo PIN code".
 rEnter a Logo PIN code
i) Press as to select a number from 0 to 9.
ii) Press the  button. 
 fThe fixed number change to , the cursor move to the next digit.
iii) Repeat the above steps, and enter a three-digit number.
 fMove the cursor to [Set] after fixing the three-digit number.
iv) Press the...

ENGLISH - 67
 fThe [Security] screen is displayed.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[PIN code lock]The [PIN code] screen will be displayed when turn on the projector. The projector cannot be 
operated without entering the PIN code.
[PIN code change]Change the PIN code.
Attention
 fThe initial PIN code is "111".
 fChange the PIN code periodically that is hard to guess.
[PIN code lock]
Set the PIN code (three-digit).
1) Press as to select...

68 - ENGLISH
6) Press the  button.
 fThe [New PIN code] input screen is displayed.
7) Enter the New PIN code according to the steps in "Enter a PIN code".
[Power management]
This function optimizes lamp power according to the operating status to reduce power consumption.
[Power management]
Set the operation as following if there is no signal input.
1) Press as to select [Power management].
2) Press the  button.
 fThe [Power management] screen is displayed.
3) Press as to switch the item.
 fThe...

ENGLISH - 69
[Filter counter]Displays the using time of the filter.
[Timer]Sets the time to display the warning  icon.
[Filter counter 
reset]Resets the filter counter.
Setting [Timer] 
If you want to clean the air filter periodically according to the operating environment, the filter warning icon [  ] 
can be displayed on the projected screen.
1) Press as to select [Timer].
2) Press the  button.
3) Press as to switch the setting of the time.
 fThe items will switch each time you press the button....

70 - ENGLISH
[Network setting]
1) Press as to select [Network].
2) Press the  button.
 fThe [Network] screen is displayed.
3) Press the  button.
 fThe [Network setting] screen is displayed.
4) Press as to select an item, and change the setting according to the instructions\
.
[DHCP] 
[On]:If a DHCP server exists in the network to which the projector is connected, 
the IP address will automatically be acquired.
[Off]:If a DHCP server does not exist in the network to which the projector is 
connected,...