Panasonic LCD Projector PT-LM1U Operating Instructions

ENGLISH
Before operating this product, please read the instructions carefully and save this
manual for future use.
LCD Projector 
Operating Instructions
Model No.
PT-LM1U
ENTER
FREEZESHUTTERINDEX
WINDOWPROJECTOR VOLUME D.ZOOMSTD AUTO
SETUPVIDEOINPUT POWER
RGB
MENU
TQBJ 0137-1
Commercial Use
R 

2-E
NGLISH
ENGLISH
-3
Preparation
IMPORTANT SAFETY NOTICE Dear Panasonic Customer:This instruction booklet provides all the necessary operating information that you
might require. We hope it will help you to get the most out of your new product,
and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should note
it in the space provided below and retain this booklet in case service is required.Model number:  PT-LM1USerial...

ENGLISH
-5
Preparation
Precautions with regard to safetyWARNINGIf you notice smoke, strange smells or noise coming from the
projector, disconnect the power cord plug from the wall outlet.
BDo not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
BCheck that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
BDo not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place...

ENGLISH
-7
Preparation
6-E
NGLISH
Do not use the projector in a bath or shower.
BFire or electric shocks can result.
Do not look into the lens while the projector is being used.
BStrong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
BBe especially careful not to let young children look into the lens. In
addition, disconnect the power cord when you are away from the projector.
Do not place your hands or other objects close to the air...

ENGLISH
-9
Preparation
8-E
NGLISH
Do not place any heavy objects on top of the projector.
BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
BFailure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct....

ENGLISH
-11
Preparation
10-E
NGLISH
Notes on useIn order to get the best picture quality
Draw curtains or blinds over any windows and turn off any
fluorescent lights near the screen to prevent outside light or
light from indoor lamps from shining onto the screen.
Do not touch the surfaces of the lens with your bare
hands.
If the surface of the lens becomes dirty from fingerprints or
anything else, this will be magnified and projected onto the
screen. Moreover, when not using the projector, retract the...

ENGLISH
-13
Preparation
12-E
NGLISH
#Connector panel (page 16)
$Air outlet port
Do not cover this port.
%Air inlet port
Do not cover this port.
&Lamp unit holder (page 50)
'Front adjustable legs (L/R) (page 23)
(Air inlet port, Air filter (page 49)
Do not cover this port.WARNINGDo not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns...

ENGLISH
-15
Preparation
14-E
NGLISH
#Power indicator (pages 22, 24 and 25)
This indicator illuminates red when the projector is in standby mode, and it
illuminates green when a picture starts to be projected.
$TEMP indicator (page 47)
This indicator illuminates if an abnormally high temperature is detected inside
the projector or around it. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.
%LAMP indicator (page 48)
This...

ENGLISH
-17
Getting started
16-E
NGLISH
Connector panel#Menu operation (on connector panel) (page 14)
$RGB IN connector (pages 19 and 20)
This connector is used to input RGB signals and YP
BPRsignals.
%S-VIDEO IN connector (pages 20 and 39)
This connector is used to input signals from a S-VIDEO-compatible
equipment such as a video deck. The connector is S1 signal compatible,
and it automatically switches between 16:9 and 4:3 aspect ratios in
accordance with the type of signal being input.
&VIDEO IN jack...

ENGLISH
-19
Getting started
18-E
NGLISH
ConnectionsNotes on connectionsBRead the instruction manual for each peripheral device carefully before
connecting it.
BTurn off the power supply for all peripheral devices before making any
connections.
BIf the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
BIf there is a lot of jitter in the video signal, the projected image may flicker.
In...