Panasonic LCD Projector PT-LM1U Operating Instructions

							ENGLISH
Before operating this product, please read the instructions carefully and save this
manual for future use.
LCD Projector 
Operating Instructions
Model No.
PT-LM1U
ENTER
FREEZESHUTTERINDEX
WINDOWPROJECTOR VOLUME D.ZOOMSTD AUTO
SETUPVIDEOINPUT POWER
RGB
MENU
TQBJ 0137-1
Commercial Use
R 
						

							2-E
NGLISH
ENGLISH
-3
Preparation
IMPORTANT SAFETY NOTICE Dear Panasonic Customer:This instruction booklet provides all the necessary operating information that you
might require. We hope it will help you to get the most out of your new product,
and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should note
it in the space provided below and retain this booklet in case service is required.Model number:  PT-LM1USerial number:WARNING: 
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
Power Supply:This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION:The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies  up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.CAUTION:This equipment is equipped with a three-pin grounding-type power
plug. Do not remove the grounding pin on the power plug. This
plug will only fit a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet, contact
an electrician. Do not defeat the purpose of the grounding plug.
Do not remove
WARNING:BNot for use in a computer room as defined in the Standard for the
Protection of Electronic Computer/Data Processing Equipment,
ANSI/NFPA 75.
BFor permanently connected equipment, a readily accessible disconnect
device shall be incorporated in the building installation wiring;
BFor pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.WARNING:This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
–  Reorient or relocate the receiving antenna.
–  Increase the separation between the equipment and receiver.
–  Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
–  Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:To assure continued compliance, use only shielded interface cables when
connecting to computers or peripheral devices. 
Any unauthorized changes or modifications to this equipment will void the
users authority to operate.
Declaration of Conformity
Model Number:  PT-LM1U
Trade Name:Panasonic
Responsible party:  Matsushita Electric Corporation of America.
Address:  One Panasonic Way Secaucus New Jersey 07094
Telephone number:  1-800-528-8601 or 1-800-222-0741
Email: [email protected]
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. 
						

							ENGLISH
-5
Preparation
Precautions with regard to safetyWARNINGIf you notice smoke, strange smells or noise coming from the
projector, disconnect the power cord plug from the wall outlet.
BDo not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
BCheck that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
BDo not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
BIf the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
BIf installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, turn off the power and disconnect the
power cord from the wall outlet.
BContinued use of the projector in this condition may result in fire or electric
shocks.
BContact an Authorized Service Center for repairs.
Do not overload the wall outlet.
BIf the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
BHigh voltages can cause fire or electric shocks.
BFor any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
BIf dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord out
from the wall outlet and wipe it with a dry cloth.
BIf not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.
4-E
NGLISH
ContentsPreparationIMPORTANT SAFETY NOTICE ...2
Precautions with regard to 
safety .........................................5
Accessories .................................9
Before use ..................................10
Location and function of each
part ...........................................12Getting startedSetting-up ...................................17
Projection methods, Projector
position, Projection distances
Connections ...............................19
Connecting to computer,
Connecting to video equipment
Preparation for the remote
control unit ..............................21Basic OperationTurning on the power ................22
Turning off the power................24Useful functionsCorrecting keystone distortion
and automatic positioning .....26
Turning off the picture and sound
momentarily ............................27
Pausing a picture.......................27
Enlarging the picture.................28
Adjusting the volume ................28
Displaying two screens.............29Adjustments and settingsOn-screen menus ......................30
Menu screens, Menu operation
guide, Returning a setting to the
factory default
Correcting keystone 
distortion .................................34
Adjusting the picture.................35
PICTURE MODE, CONTRAST,
BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP.,
White balance R/G/B, AI, 
TV-SYSTEM, STILL MODE,SIGNAL MODE, Projecting sRGB-
compatible pictures
Adjusting the position...............38
POSITION, DOT CLOCK, CLOCK
PHASE, ASPECT, RESIZING,
FRAME LOCK
Changing the display 
language ..................................41
Option settings ..........................42
OSD, AUTO SIGNAL, AUTO
KEYSTN, RGB/YP
BPR,
VGA60/525P, SXGA MODE, BACK
COLOR, FRONT/REAR,
DESK/CEILING, FAN CONTROL,
LAMP POWER, LAMP RUNTIME,
FUNC 1, CONTROL KEY, 
AUTO POW.OFF, POWER
MEMORY
Setting up the security 
function ...................................45
INPUT/AMEND PASSWD, 
TEXT DISPLAY/CHANGE
Care and maintenanceWhen the TEMP indicator and the
LAMP indicator are 
illuminated...............................47
Cleaning and replacing 
the air filter ..............................49
Replacing the lamp unit ............50
Before calling for service..........53
Cleaning and maintenance .......55OthersSpecifications ............................56
Appendix ....................................58
List of compatible signals,
Connector pin wiring, Projection
dimensions calculation methods
Dimensions ................................60
Trademark 
acknowledgements ................60
NOTES IMPORTANTES
CONCERNANT LA SÉCURITÉ
...61
Précautions de sécurité
..............62
Avant l’utilisation
...............................66
Remplacement du bloc de lampe
...68 
						

							ENGLISH
-7
Preparation
6-E
NGLISH
Do not use the projector in a bath or shower.
BFire or electric shocks can result.
Do not look into the lens while the projector is being used.
BStrong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
BBe especially careful not to let young children look into the lens. In
addition, disconnect the power cord when you are away from the projector.
Do not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Replacement of the lamp unit should only be carried out by a qualified
technician.
BThe lamp unit has high internal pressure. If improperly handled, explosion
might result.
BThe lamp unit can easily become damaged if struck against hard objects
or dropped, and injury or malfunctions may result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
BThe lamp cover gets very hot, and contact with it can cause burns.
Before replacing the lamp, be sure to disconnect the power cord from
the wall outlet.
BElectric shocks or explosions can result if this is not done.CautionDo not cover the air inlet or the air outlet.
BDoing so may cause the projector to overheat, which can cause fire or
damage to the projector.
BDo not place the projector in narrow, badly ventilated places such as
closets or bookshelves.
BDo not place the projector on cloth or papers, as these materials could be
drawn into the air inlet port.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
BUsing the projector under such conditions may result in fire or electric
shocks.
When disconnecting the power cord, hold the plug, not the cord.
BIf the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
BMoving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur. Do not do anything that might damage the power cord or the power
cord plug.
BDo not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
BIf the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
BAsk an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
BFailure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
BIf the plug is not inserted correctly, electric shocks or overheating could
result.
BDo not use plugs which are damaged or wall outlets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
BIf the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
BFailure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
BIf water spills onto the projector or gets inside it, fire or electric shocks
could result.
BIf any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
BDo not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Keep the batteries out of the reach of infants.
BIf the batteries are swallowed, death by suffocation may result. If you
believe that the batteries may have been swallowed, seek medical advice
immediately.
Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.
BFailure to observe this may cause the batteries to leak, overheat, explode
or catch fire.
BStore the batteries in a plastic bag and keep them away from metallic
objects.
During a thunderstorm, do not touch the projector or the cable.
BElectric shocks can result. 
						

							ENGLISH
-9
Preparation
8-E
NGLISH
Do not place any heavy objects on top of the projector.
BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
BFailure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct.
BIf the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Use only the specified batteries.
BIf incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Insulate the battery using tape or similar before disposal.
BIf the battery comes into contact with metallic objects or other batteries, it
may catch fire or explode.
Do not put your weight on this projector.
BYou could fall or the projector could break, and injury may result.
BBe especially careful not to let young children climb onto the projector.
If not using the projector for an extended period of time, disconnect the
power cord plug from the wall outlet.
BIf dust builds up on the power cord plug, the resulting humidity may
damage the insulation, which could result in fire.
BThis projector continues to draw approximately 5 W of power even when
the power is turned off.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
BElectric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least
once a year.
BIf dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
BIt is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company.NOTICE:
BThis product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: 
Card remote control unit
(TNQE239 x1)
Power cord
(K2CG3DR00005 x 1) Lithium battery for
remote control unit
(CR2025 x1)RGB signal cable 
[1.8 m (5´10˝),
K1HA15DA0002 x1]AccessoriesCheck that all of the accessories shown below have been included with your
projector.
ENTER
FREEZE
SHUTTER
INDEX
WINDOWPROJECTOR VOLUME D.ZOOMSTD AUTO
SETUPVIDEOINPUT POWER
RGB
MENU
Softcase 
(TPEP012 x 1) 
						

							ENGLISH
-11
Preparation
10-E
NGLISH
Notes on useIn order to get the best picture quality
Draw curtains or blinds over any windows and turn off any
fluorescent lights near the screen to prevent outside light or
light from indoor lamps from shining onto the screen.
Do not touch the surfaces of the lens with your bare
hands.
If the surface of the lens becomes dirty from fingerprints or
anything else, this will be magnified and projected onto the
screen. Moreover, when not using the projector, retract the
lens and then cover it with the lens cover.
Screen
Do not apply any volatile substances which may cause
discoloration to the screen, and do not let it become dirty or
damaged.
Lamp
The lamp may need to be replaced earlier due to variables
such as individual lamp characteristics, usage conditions and
the installation environment, especially when the projector is
subjected to continuous use for more than 10 hours or the
power is frequently turned on and off.
Liquid crystal panel
The liquid crystal panel of the projector is built with very high
precision technology to provide fine picture details.
Occasionally, a few non-active pixels may appear on the
screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your
LCD.
Cautions regarding setting-upAvoid setting up in places which are subject to vibration
or shocks.
The internal parts can be damaged, which may cause
malfunctions or accidents.
Do not set up the projector near high-voltage power lines
or near motors.
The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified
technician to carry out all installation work.
You will need to purchase the separate installation kit (Model
No.ET-PKM1). Furthermore, all installation work should only
be carried out by a qualified technician.
If using this projector at high elevations (above 1 400 m),
set the “FAN CONTROL” to “HIGH”. (Refer to page 43.)
Failure to observe this may result in malfunctions.Before useCaution when moving the projectorBe sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and
shocks. When moving the projector, use the accessory softcase.
When placing the projector inside the softcase, position it so that
the lens is facing upward.
Attach the lens cover so that the direction of the “Panasonic”
logo becomes as shown in the figure above. 
						

							ENGLISH
-13
Preparation
12-E
NGLISH
#Connector panel (page 16)
$Air outlet port
Do not cover this port.
%Air inlet port
Do not cover this port.
&Lamp unit holder (page 50)
'Front adjustable legs (L/R) (page 23)
(Air inlet port, Air filter (page 49)
Do not cover this port.WARNINGDo not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.Projector 

Location and function of each part#Focus ring (page 23)
$Zoom ring (page 23)
%Speaker
&Projector control panel (Top) (page 14)
'Remote control unit holder
Store the remote control unit as shown in the figure above.
(Leg adjuster buttons (L/R) (page 23)
These buttons are used to unlock the front adjustable legs. Press to adjust
the angle of tilt of the projector.
)Lens cover
*Projection lens
+Remote control signal receptor (page 21)
,Air inlet port
Do not cover this port.Projector 

ENTER
FREEZESHUTTERINDEX
WINDOWPROJECTOR VOLUME
D.ZOOM STD AUTO
SETUPVIDEOINPUT POWER
RGB
MENU
#$ % &
'
(
) * +
, (
#$%
&
' (
NOTE:
BDuring projection of an image, the cooling fan will operate, emitting a
small noise as it operates. Turning the lamp on or off will cause this
noise to increase a little.
BBy using the “OPTION2” menu to set “LAMP POWER” to “LOW”, the
operating sound of the fan can be reduced. (Refer to page 43.) 
						

							ENGLISH
-15
Preparation
14-E
NGLISH
#Power indicator (pages 22, 24 and 25)
This indicator illuminates red when the projector is in standby mode, and it
illuminates green when a picture starts to be projected.
$TEMP indicator (page 47)
This indicator illuminates if an abnormally high temperature is detected inside
the projector or around it. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.
%LAMP indicator (page 48)
This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.
&RGB INPUT indicator 
This indicator illuminates when a signal is being input to the RGB IN
connector.
'POWER button (pages 22 and 24)
(INPUT buttons (page 23)
These buttons are used to switch the input signals from the connected equipment.
)AUTO SETUP button (pages 23 and 26)
If this button is pressed while a picture is being projected, the projection
settings will be adjusted automatically in accordance with the signal being
input. In addition, the angle of tilt of the projector will be automatically
detected and adjusted in order to correct any keystone distortion.
*MENU button (pages 30 and 32)
This button is used to display the “MAIN MENU”. When a menu screen is
being displayed, this button can be used to return to a previous screen or
to clear the screen.
+Arrow (F FG
GI
I
and H H
) buttons (page 32)
These buttons are used to select and adjust items in the on-screen menus.
,ENTER button (page 32)
This button is used to accept and to activate items selected in the on-screen menus.
-FREEZE button (page 27)
This button is used to momentarily freeze projection so that a still picture is displayed.
.SHUTTER button (page 27)
This button is used to momentarily turn off the picture and sound.
/VOLUME +/- buttons(page 28)
These buttons are used to adjust the volume of the sound output from the
projector’s built-in speaker. Refer to page 31 for details on how to adjust
the volume using the buttons on the projector control panel.
0STD (standard) button (page 33)
This button is used to reset the projector adjustment values to the factory
default settings.
1INDEX WINDOW button (page 29)
This button can be used to split the image projection area into a still
picture and a moving picture.
2D.ZOOM +/- buttons (page 28)
These buttons are used to enlarge the projected image.
Menu
operation
Remote control unit
$
%'(
&)
˛ #
*
+,
FREEZE
SHUTTER
INDEX
WINDOWPROJECTORSTD AU TO
SETUPINPUT POWER
MENUENTERVIDEO RGB
VOLUME
D.ZOOM
'
(
+-
.
/
0
1
2,
)
*
Projector control panel 
 
						

							ENGLISH
-17
Getting started
16-E
NGLISH
Connector panel#Menu operation (on connector panel) (page 14)
$RGB IN connector (pages 19 and 20)
This connector is used to input RGB signals and YP
BPRsignals.
%S-VIDEO IN connector (pages 20 and 39)
This connector is used to input signals from a S-VIDEO-compatible
equipment such as a video deck. The connector is S1 signal compatible,
and it automatically switches between 16:9 and 4:3 aspect ratios in
accordance with the type of signal being input.
&VIDEO IN jack (page 20)
This jack is used to input video signals from a video equipment such as a
video deck.
'AUDIO IN L-R jacks (pages 19 and 20)
(Power input socket (AC IN) (page 22)
The accessory power cord is connected here.
Do not use any power cord other than the accessory power cord.
)Security lock 
This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.
Setting-upProjection methodsIn way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION2” menu. Refer
to page 43 for details.)
BFront-desk projectionBFront-ceiling projection
BRear-desk projection
(Using a translucent screen)BRear-ceiling projection
(Using a translucent screen)
Menu items Setting
FRONT
DESK FRONT/REAR
DESK/CEILING
Menu items Setting
FRONT
CEILING FRONT/REAR
DESK/CEILING
Menu items Setting
REAR
DESK FRONT/REAR
DESK/CEILING
Menu items Setting
REAR
CEILING FRONT/REAR
DESK/CEILING
NOTE:
BYou will need to purchase the separate ceiling bracket (ET-PKM1)
when using the ceiling installation method.
BIf you set up the projector vertically, it may cause
to damage the projector.
B
It is recommended that you set up the projector
in a place that is tilted at less than 
±30°
. Setting
up the projector in places that are tilted at more
than 
±30°
may cause malfunctions.
#
$
(
)
& %
' 
						

							ENGLISH
-19
Getting started
18-E
NGLISH
ConnectionsNotes on connectionsBRead the instruction manual for each peripheral device carefully before
connecting it.
BTurn off the power supply for all peripheral devices before making any
connections.
BIf the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
BIf there is a lot of jitter in the video signal, the projected image may flicker.
In such cases, it will be necessary to connect a TBC (time base corrector).
BRefer to the list on page 58 for details on compatible signals which can be
input to the projector.
BOnly one audio system circuit is available for the AUDIO IN L-R jacks, so if
you change the audio input source, you will need to remove and insert the
appropriate plugs.
Projector position
H1
L
L
SHSW
63.5
 (2-1/2)
L: Projection distance
SH: Image height
SW: Image width
H1: Distance from center
of lens to bottom edge
of projected image Top edge of screen
Screen
Bottom edge of screen
Screen
NOTE:
BThe dimensions in the table above are approximate.
BIf you use the projection distance for the 16:9 screen,
the 4:3 projection image overflows the screen at the top
and bottom.
BFor details about projected image distances, refer to
page 59.

Projection distances0.84 m(33˝) 0.50 m(1´7˝) 0.67 m(2´2˝)
−
1.2 m(3´11˝)
0.07 m(2-3/4˝)
1.01 m(40˝) 0.61 m(2´) 0.81 m(2´8˝) 1.2 m(3´11˝) 1.4 m(4´7˝)
0.09 m(3-17/32˝)
1.27 m(50˝) 0.76 m(2´6˝) 1.02 m(3´4˝) 1.5 m(4´11˝) 1.8 m(5´10˝)
0.11 m(4-5/16˝)
1.52 m(60˝) 0.91 m(3´) 1.22 m(4´) 1.9 m(6´2˝) 2.1 m(6´10˝)
0.13 m(5-3/32˝)
1.77 m(70˝) 1.07 m(3´6˝) 1.42 m(4´8˝) 2.2 m(7´2˝) 2.5 m(8´2˝)
0.15 m(5-7/8˝)
2.03 m(80˝) 1.22 m(4´) 1.63 m(5´4˝) 2.5 m(8´2˝) 2.9 m(9´6˝)
0.17 m(6-11/16˝)
2.28 m(90˝) 1.37 m(4´6˝) 1.83 m(6´) 2.8 m(9´2˝) 3.2 m(10´5˝)
0.20 m(7-27/32˝)
2.54 m(100˝) 1.52 m(5´) 2.03 m(6´8˝) 3.1 m(10´2˝) 3.6 m(11´9˝)
0.22 m(8-21/32˝)
3.81 m(150˝) 2.29 m(7´6˝) 3.05 m(10´) 4.6 m(15´1˝) 5.4 m(17´8˝)
0.33 m(12-31/32˝)
5.08 m(200˝) 3.05 m(10´) 4.06 m(13´4˝) 6.2 m(20´4˝) 7.3 m(23´11˝)
0.44 m(17-5/16˝)
6.35 m(250˝)
7.62 m(300˝)3.81 m(12´6˝)
4.57 m(15´)5.08 m(16´8˝)
6.10 m(20´)9.1 m(29´10˝)
10.9 m(35´9˝)
0.54 m(21-1/4˝)0.65 m(25-9/16˝)
Screen size (4:3)
Diagonal
lengthHeight 
(SH)Width 
(SW)Projection distance (L)
Height
position
(H1) Wide 
(LW)Telephoto 
(LT)
7.7 m(25´3˝)
9.3 m(30´6˝)
Computer
Connecting to computer
RGB signal cable
(accessory)