Panasonic LCD Projector PT-L730NTU Operating Instructions

							101
Settings of wireless card
q q
Click the icon on the task bar and,
from Menu, open Advanced
Settings.
w w
Enter the name in Profile Name to
preserve the settings.
The initial value is set to  Default .
Only alphanumeric characters and symbols are
acceptable.
e e
If the Communication mode is set to
Infrastructure (Access Point):
Set Network name (SSID) to the same setting as
the projector.
If the Communication mode is set to
AdHoc (Pseudo AdHoc):
Set the channel to the same number as the
projector.
r r
If WEP (encryption) has been set in
the projector:
Select the WEP mode, and set it to the same
settings as the projector and the access point.
64 (40) bit encryption 
To enter an encryption key:
Characters: 5 characters
Hexadecimal numbers: 10 digits
Select a default key number from 1 to 4.
128 (104) bit encryption 
To enter an encryption key:
Characters: 13 characters
Hexadecimal numbers: 26 digits
Select a default key number from 1 to 4.
t t
Click the  Apply  button.
Click the  OK  button to close the window.        
						

							102
Settings of personal computer
TCP/IP setting
 For WindowsMe
q
q
Right-click the Network Computer
icon and open Properties.
w w
Select TCP/IP -> Panasonic Wireless
Card, and click the Properties
button.
e e
Enter an IP address of the same
segment as the one assigned to the
projector.
r r
Enter the same value as the subnet
mask assigned to the projector.
t t
To communicate in AdHoc mode,
delete the gateway.
To communicate in Infrastructure
mode, set a proper gateway.
After the entry, click the OK button to return to
the previous screen.
y y
Click the OK button to complete the
setting procedure.
Rebooting the PC will establish the settings.
 For Windows98SE
•To install the driver in a Windows98SE machine, refer to the procedures for
WindowsMe.        
						

							 For WindowsXP
q
q
Right-click the My Network icon
and open Properties.
w w
Right-click the My Network icon
and open Panasonic Wireless Card.
e e
Select Internet Protocol (TCP/IP),
and click the Properties button.
r r
Enter an IP address of the same
segment as the one assigned to the
projector.
t t
Enter the same value as the subnet
mask assigned to the projector.
After the entry, click the OK button to return to
the previous screen.
y y
Click the OK button to complete the setting procedure.
You do not have to restart the computer.
 For Windows2000•To install the driver for Windows2000, refer to the procedure for WindowsXP.
103      
						

							If two or more network devices are existent
 For WindowsMe
q
q
Right-click the My Computer icon
and click Properties to open the
System Properties window.
w w
Open Device Manager, and select
the icon of the device you want to
disable, and click the Properties
button.
e e
Check the Disable in this hardware
profile checkbox and click the OK
button.
r r
Confirming that each icon of the
disabled adaptors is marked with X,
click the OK button to close the
window.
 For Windows98SE•To install the driver in a Windows98SE machine, refer to the procedures for
WindowsMe.
104       
						

							105
 For WindowsXP
q
q
Right-click the My Network Places
icon and select Properties, and
open the Network connection
window.
w w
Right-click the icon of the device you
want to disable and select Disable.
e e
Making sure the icon of the device
you just disabled is gray, close the
window.
 For Windows2000•To install the driver for Windows2000, refer to the procedure for WindowsXP.     
						

							106
Web browser control
What you can do with Web browser
control
With the web browser, the user can access the projector for set-up using the projector
control and handle the SD card data loaded in the projector using the SD control.
Settings of Web browser control
Settings of projector
q q
Press the MENU button to display the menu.
w w
Use the  and  buttons to display the
Option screen.
e e
Press the ENTER button to display the
Option  set-up screen. 
Settings can be altered with  ,  ,  and 
buttons.
Press the ENTER button when necessary changes are
completed.
Web controlON: Enables the web browser control.
OFF: Disables the web browser control.
Web powerON: Allows the user to turn on the power of the projector
using the web browser control.
OFF: Does not allow the user to turn on the power of the
projector using the web browser control.
Web passwordThe user can set a password using up to 16 alphanumeric
characters and symbols.
Use  buttons to change letters, use  buttons to move the digit.
No password has been set as a factory default.
Settings of personal computer
q q
Right-click Internet Explorer icon
and open Properties.
w w
From Connection, open LAN
setting, clear all the check boxes of
options and click the OK button.
Click the OK button to close the set-up window.
Note:•If the proxy server is already used, in Advanced
Settings set IP address of the connecting projector
as an exception not to use the proxy server.
e e
In Security, set the security level to
the Default level. Or otherwise, from
Custom level enable Active script.
OPTIONSHUTTER
OSD
AUTO KEYSTONE
RGB/YPbPr
AUTO RGB IN
RGB2 SELECT
BACK COLOR
FRONT/REAR
DESK/CEILING
LAMP POWER
LAMP RUN TIME
NEXT PAGE  
↓10 H OFF
OFF
RGB
OFF
INPUT
BLUE
FRONT
DESK
LOWON
ON
YPbPr
ON
OUTPUT
BLACK
REAR
CEILING
HIGH
SELECT:[ ↑ ][ ↓ ]ENTER:[ENTER]
ESC  :[MENU]
OPTIONBACK PAGE ↑FAN CONTROL
WEB CONTROL
WEB STANDBY
WEB PASSWORD
CONTROL KEY
FUNC1STANDARD
OFF
OFF
OFF
MUTEHIGH
ON
ON
ON
KEYSTONE
SELECT:[ ↑ ][ ↓ ]
ADJUST:[←][→]ENTER:[ENTER]
ESC  :[MENU]     
						

							107
Note:•  For Netscape, go to  “Edit ” →  “ Setting ” →  “ Details ” and enable JavaScript.
Operation of  Web b ro wser cont rol
Sta rting  Web b ro wser cont rol
Sta rt the b ro wser (Mic rosoft Internet Explorer is used as an
e xample here), and enter the IP a ddress assigned to the
p rojecto r.
Web browser control will be started.
Note:•   Web browser control can also be started from Wireless Manager 2.0.
While Wireless Manager 2.0 is running, right-click the icon shown on the\
 task bar,
select and left-click  Remote Control .
Top screen 
Note:•  The top screen may not be displayed depending on the browser. In that ca\
se, close
the window first and start again the Web browser control, or press the \
CLT + H
buttons at the same time.
Disa ble the use of the pr oxy se rv er (to use 
the pr oxy se rv e r, re fer to Settings of 
W eb br owser control on page  106).
Specify the IP address that has been assigned to 
the projector in the network setting.
Select Japanese or English.
Enter the password if any has been defined.
In case you forget the password, assign a new 
password to the projector (For security reason, 
the projector does not show the password that 
you have been using).Note:   
						

							108
Projector control 
Click Projector control in the menu.The user can make various settings of the projector.
Basic control screen 
Notes:•When the power is turned ON, the
window is closed for the moment. Then,
confirming that the light is turned on, start
operation again from the top screen.
•Connection with the projector cannot be
established just after turning on the
power. In this case, wait for a while and
try connection again.
•
If Web control is not turned ON in the
option setting of the projector, neither basic
control nor option control will operate.
•Web power is not turned ON in the
option setting of the projector, it will not
be powered on. However, the projector
control screen will display still the same
content as shown when the projector
operates normally.
Option control screen 
Note:•If the projector does not work as
controlled, ensure that the Web control is
set to ON in the Option menu.
Monitor information screen 
Note:•Monitor information is updated at
regular intervals. If you go to Display
and press the Refresh button, you can
check the current and accurate
information.       
						

							109
SD control 
q q
Switch to SD CARD by using the input selector (INPUT,
RGB) button of the projector or the remote control.
It is also possible to switch to it on the basic control screen of the projector
control.
w w
Click SD control in the menu.
SD file list screen 
SD thumbnail screen 
Changing password 
Click Change password in the menu.The user can change the password.
Note:•Up to16 characters can be used for a
password.
Use alphanumeric characters and
symbols to create a password.
Both upper and lower case letters can
be used.
Select a folder in the SD card.
Select thumbnail display or file name list display.
Control auto-play. 
Clicking a file name will zoom in on it 
within the Web browser.
Clicking  Projection  will display the file 
by on projector.
Clicking an image will zoom in on it 
within the Web browser.
Clicking Projection will display it 
on the projector.   
						

							110
Wireless Manager 2.0
What you can do with Wireless
Manager 2.0
Wireless Manager 2.0 provides the following functions:
•To register multiple projectors that are on the network.
•To capture images on the computer screen and transmit them to the projector.
•To view the list of existing image files in the folder, from which the user can select
the desired images and transmit them to the projector. In addition, the software
also allows the user to enjoy automatic playback.
•To transmit image data onto the SD card inserted in the projector and stack images
in advance. This function allows quick image switching.
Note:•Wireless Manager 2.0 supports BMP, JPEG, and PNG image formats.
•Wireless Manager 2.0 cannot be used with the earlier model of PT-L712NTU.
Installation of Wireless Manager 2.0Install the Wireless Manager 2.0 onto your PC.
The software is contained in the supplied CD-ROM.
Before installationThe software does not run on the computer that does not operate with
Windows98SE/Me/2000/XP.
Procedure of installation
q q
Insert the CD-ROM into the CD-ROM drive.
w w
Open WIRELESS MANAGER 2.0 folder in the CD-ROM.
e e
Open English folder.
r r
Double-click and run Setup.exe.
Go on installation operation following the instructions shown on the screen.