Panasonic LCD Projector PT-L730NTU Operating Instructions

81
The supplied Wireless Manager 2.0 allows the user to
transfer image data from the personal computer to the SD
card inserted in the projector and to record the data on the
card. Thus the user can project images changing very
quickly to desired ones.
Example of use of wireless functions
The Web browser allows the user to access the projector
and to project the image data stored on the SD card
inserted in the projector.
Trans ferring im ag e data f rom pe rsonal
computer to the p rojector and reco rding...

82
Fitting and removal of SD
card and wireless card
SD card
Removal
q q
Open the slot cover
w w
Confirm that the access
lamp is not blinking (i.e., SD
card is not under reading or
writing operation) at the
right back of the slot.
Note: 
•Be sure to confirm that the access
lamp is not blinking when to remove
the card. Removing the SD card while
the access lamp is blinking may
destroy the data stored on the card.
e e
Press the center of the SD
card to release the lock and
remove the card
r r
Close the slot...

83
Wireless card 
Fitting
q
q  
T urn off the p ower to the
p rojector
Turn off the power referring to  How
to turn off the power supply  given on
page  28.
w
w
Open the slot cover
e
e
Insert the wireless card
With the side of power monitor facing
up, insert the card until it reaches the
depth and is locked.
Note: •Pay attention to the difference
between up and down sides of the
wireless card. Forcible insertion of the
wireless card in a wrong direction may
cause a fault.
r
r
Close the slot cover...

84
How to use SD card
Setting 
q q
Press the MENU button to view the
menu
w w
Using the and buttons, show the
SD card screen
e e
Press the ENTER button to show the
SD card setting screen.
r r
Using the and buttons, select the
desired item, and make setting with the
and buttons.PICTUREPICTURE MODE
COLOR TEMP.
BRIGHT
CONTRAST
SHARPNESS
WHITE BALANCE R
WHITE BALANCE G
WHITE BALANCE B
STANDARDSTANDARD
STANDARD
32
32
0
32
32
32
SELECT:[
↑][↓]
ADJUST:[←][→]ENTER:[ENTER]
  ESC:[MENU]
SD CARDAUTOPLAY
REPEAT...

85
Replay
q q
Change to SD card using the input
switching (INPUT, RGB) button of the
projector or remote controller.
w w
Select the folder with the  and
buttons and press the
ENTER button.
A file selection screen will appear.
Notes: •If three or more folders are found, press the
button and the next three (or less)
folders will be shown in turn.
•If no thumbnail has been incorporated in the
image file in advance, it will take a longer
time before image appears.
•A folder that contains no image file...

86
Recording direct ly on SD ca rd
Use the SD card by means of a PC card adaptor in a personal computer hav\
ing a slot
that is compatible to TYPE 2 or TYPE 3 PC (PCMCIA) card.
For a Windows machine, the supplied software, Image Creator 1.0, will be\
 available
for compiling and storing.
For details of Image Creator 1.0, refer to  Image Creator 1.0 on page  118.
Compiling on Windows
If your PC is a Windows machine, the supplied software, Image Creator 1.\
0 can be
used. With this Image Creator 1.0, the...

87
If this is the second or forward time of SD card insertion, no setting o\
peration is
required.
r
r  
Select Create list of all drive rs
e xisting in specific location and select
the driver  for installation and  cli ck the
N ext  button.
t
t  
Select Standa rd IDE/ESDI ha rd disk
cont roller and  cli ck the N ext  button.
From now on, go on installation operation following
the instructions on the screen. Finally, click the
Complete button to finish the preparatory
operation for SD card use.
y
y...

88Removing SD card
Take out the SD card in the following procedure:
q q
Quit all software applications that use the SD card.
w w
Left-click the PC card icon ( ) shown on the task bar at the
right bottom on the screen.
Note: 
•If no PC card icon is appearing on the task bar at the right bottom of the screen, go
to Start menu →Setting →Control panel, open PC card, click the Show control
on the task bar check box, and then click the OK button.
e e
Select either Disable standard
IDE/ESDI hard disk controller...

89
Compilation on Macintosh machine The supplied software, Image Creator 1.0, is not available in Macintosh \
machines.
However, it is possible to write and compile images stored in the person\
al computer.
Fitting SD ca rd
q
q  
Inse rt the SD ca rd into the PC ca rd
adaptor as sh own in the di agram on
the right.
Positively push in the card until it is locked. Also
pay attention to the difference between up and
down sides and fore and back sides when
inserting the card.
Note: •   If the SD card is...

90S
aving im ag es in Macintosh onto the SD ca rd.
JPEG images that were created with graphic software or captured by digit\
al camera
into Macintosh can be saved onto the SD card and replayed with the proje\
ctor.
Note: •  Fully read DCF standard on page  124 and perform file operation.
q
q
Open the icon of SD card drive and press the   + N
buttons to create a new folder (directory) and rename it DCIM.
A DCIM directory already exists in an SD card in which any file has been\
 saved
as a result of image...