Panasonic LCD Projector PT-F200NTU PT-F200U Operating Instructions

Care and Replacement
ENGLISH - 41
Maintenance
JResetting the FILTER 
REMAINING
1. Turn on the projector and display the FILTER 
REMAINING in OPTION menu. Press the ENTER 
button for 3 seconds and the confirmation screen 
will be displayed. 
2. Press I to select OK and press the ENTER 
button to reset FILTER REMAINING to “0”. 
See 
“FILTER REMAINING” on page 34.
JBefore replacing the Lamp unit
 Switch off the MAIN POWER and disconnect the power plug from the wall socket.
 Wait for more than 1 hour and...

Maintenance
Care and Replacement
ENGLISH - 42
JReplacement procedure
QRemoving and replacing the lamp unit
1. Use a Phillips-head screwdriver to loosen the 2 
Lamp unit cover fixing screws on the back of the 
projector until the screws turn freely, and remove 
the Lamp unit cover.
2. Use a Phillips-head screwdriver to loosen the 2 
Lamp unit fixing screws.
3. Hold the handles of the Lamp unit and release the 
lamp unit lock.
4. Pull the used Lamp unit gently from the projector.5. Replace the new Lamp...

ENGLISH - 43
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference 
page
Power does not turn on.
 The power cord may not be connected.
 The MAIN POWER switch is turned off.
 No electric supply is at the wall socket.
 TEMP indicator is lit or flashes.
 LAMP indicator is lit or flashes.
 The lamp unit cover has not been securely installed.
 The circuit breakers have tripped.20
21
20
39
39
42
-
No picture appears.
 The video signal input source may not be...

ENGLISH - 44
Appendix
Technical Information
List of compatible signals
Mode
Display 
resolution 
(dots)
*1
*1. The “i” appearing after the resolution indicates an interlaced signal.
Scanning 
frequencyDot clock 
frequency
(MHz)Picture 
quality
*2
*2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
B Some loss of data occurs to make projection easier.Terminals
H...

Technical Information
ENGLISH - 45
Appendix
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface 
specification, so that the projector can be controlled by a personal computer which is connected to this connecter.
JConnection
JPin assignments and signal names
JCommunication settings
JBasic format
 The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds 
before sending the command.
 If sending multiple...

Appendix
Technical Information
ENGLISH - 46
JCable specifications
(When connected to a personal computer)
JControl commands
You can switch the signals which to output from the COMPUTER1 OUT terminal by pressing the computer key 
command. The key commands are depend on the manufactures. If you select the computer terminals which has no 
signals while the INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. 
CommandControl contentsRemarks
PONPower ONIn standby mode, all...

Technical Information
ENGLISH - 47
Appendix
You can remotely operate the projector from the outside the Remote control range by connecting to the REMOTE 
terminal.
JPin assignments and signal names
JLAMP switching
JSwitching input signals
REMOTE terminal
Pin No.Signal nameContents
AGND Ground
BPOWER POWER ON
CINPUT SEL3 Select input signal 3
DNC
EINPUT SEL1 Select input signal 1
FINPUT SEL2 Select input signal 2
GConnect internallyH
I
ENABLE Control by external contact
Pin No.Settings
B - AShort Open...

Appendix
Technical Information
ENGLISH - 48
Specifications
Power supplyAC 100 - 240 V 50 Hz/60 Hz
Power consumption330 W
During standby (when fan is stopped): 3.5 W
Amps3.9 A - 1.4 A
LCD panel
Panel size (diagonal)0.7 type (17.78 mm)
Aspect ratio4 : 3
Display method3 transparent LCD panels (RGB)
Drive methodActive matrix method
Pixels786 432 (1 024 x 768) x 3 panels
LensManual zoom (2x)/Manual focus
F 1.7 - 2.6, f 21.6 mm - 43.0 mm
LampUHM lamp (250 W)
Luminosity*1
*1. Measurement, measuring conditions...

Technical Information
ENGLISH - 49
Appendix
Terminals
S-VIDEO INSingle - line, Mini DIN 4p
Y: 1.0 V [p-p], C: 0.286 V [p-p], 75Ω
VIDEO INSingle - line, RCA pin jack
1.0 V [p-p], 75Ω
COMPUTER1 INSingle - line, D - sub HD 15-pin (female)
R.G.B.
0.7 V [p-p], 75 
Ω
HD, VD/SYNCTTL high impedance, automatic 
positive/negative polarity 
compatible
COMPUTER2 IN/
1OUTSingle - line, D - sub HD 15-pin (female)
Selectable for input and output by menu operation.
R.G.B.
0.7 V [p-p], 75 Ω
HD, VD/SYNCTTL high impedance,...

Appendix
Technical Information
ENGLISH - 50
* All measurements above are approximate and may differ slightly from the actual measurements.
JCalculation methods for screen dimensions
You can calculate more detailed screen dimension from the screen diagonal.
SW (m) = SD () x 0.0221 SH (m) = SD () x 0.0125
LW (m) = 0.0332 x SD () - 0.049 LT (m) = 0.066 x SD () - 0.055
* The results above are approximate and may differ slightly from the actual measurements.
Screen size and throw distance for 16:9 aspect...