Panasonic Kx Utg Getting Started Manual

							Installation and Setup
11
Installation and Setup
Notice• Panasonic assumes no responsibility for injuries or property damage resulting 
from failures arising out of improper installation or operation inconsistent with 
this documentation.
Attaching the Stand
Notice
• If you place the display face down when you attach the stand, be sure to 
place a soft cloth under the display. Failure to do so may result in damage to 
the display.
1. Insert the catches (1) of the stand into the hooks located in the unit.2. Gently push the stand in the direction indicated until it locks into place.
The stand will be mounted in the high position.
A
Removing the Stand1. Hold the stand with both hands.2. Gently rotate the stand in the direction indicated until it is released.  
						

							Installation and Setup
12
Connections
To a switching hub (Ethernet cable) To a PC (Ethernet cable)To an EHS 
Optional AC adaptor
AC adaptor
Clamp
HandsetHeadset
To a handset jack   (handset)
To a headset
CAUTIONOptional AC Adaptor• Use the following AC adaptor: –DSA-42D-48 2 480063 (P/N: 381.00398.005)• The AC adaptor is used as the main disconnect device. Ensure that  the AC outlet is installed near the unit and is easily accessible.When connecting a headset• Ensure that the headset cord has slack and is not pulled tight during use to prevent damage to the connectors.• Cords used to connect devices to the EHS jack or headset jack must be less than 3 m (9.8 ft) in length.Notice• The following headsets can be used with this unit. (Not all operations with the headsets can be guaranteed.) –EHS headsets/USB headsets (KX-UTG300 only) Selected Plantronics®-brand headsetsSelected Jabra®-brand headsets 
DSA-48PFA-48 2 480063 (P/N: 381.00511.005)  
						

							Installation and Setup
13
 
– Bluetooth
® headsets (KX-UTG300 only)
For up-to-date information about headsets that have been tested 
with this unit, refer to the following web site:
http://www.panasonic.com/sip
When connecting the Ethernet cable
• Connect the Ethernet cable as shown in the following illustration.
• 
Ethernet cableEthernet cable
Incorrect Correct
60 mm 
(2 3
/8 \fn) or less
Use the included Ethernet cable.
When connecting to a switching hub
• If PoE is available, an AC adaptor is not needed. An AC adaptor must 
be used when the KX-UTA336 Add-on key module is installed to the 
KX-UTG300.
•  This unit complies with the PoE Class 2 standard.
When connecting a PC
•  Only a PC can be connected to the PC port. Other SIP phones, or 
network devices such as routers or switching hubs, cannot be connected.
• The PC port does not support PoE for connected devices.
When connecting cables and the AC adaptor
• Ensure that the Ethernet cable and the AC adaptor cord are clamped 
to prevent damage to the connectors.
When registering a Bluetooth headset (KX-UTG300 only)
• One Bluetooth headset can be registered to this unit. For details, see 
the Operating Instructions.  
						

							Installation and Setup
14
Installing the KX-UTA336 (KX-UTG300 only) 
The optional KX-UTA336 allows 36 additional flexible buttons 
(3 pages of 12) to be used with the KX-UTG300. These 
flexible buttons are used to make calls or receive calls, or 
perform a feature that has been assigned to the button. A 
maximum of 2 KX-UTA336 Add-on key modules can be con-
nected to the KX-UTG300.
Notice • An AC adaptor must be used to supply power when the KX-UTA336 Add-on 
key module is installed to the KX-UTG300.
1. Remove any devices or cords connected to the USB port.2. Remove the Add-on key module slot cover ( A).
A  
						

							Installation and Setup
15
3. Connect the KX-UTA336 (A) to the KX-UTG300 (B) by inserting the connec-
tor (C) into the Add-on key module slot ( D).
A
C
B
D
 4. Secure the KX-UTA336 to the KX-UTG300 by inserting the 2 screws supplied 
with the KX-UTA336 into the rear of the KX-UTG300.  
						

							© Panasonic System Communications Company of North America 2016
540.00938.015**C540.00938.015