Panasonic Kx Utg Getting Started Manual

Getting Started
SIP Phone
Model No.  KX-UTG200 
KX-UTG300
Thank you for purchasing this Panasonic product.  Please read this manual carefully before using this product and save this manual for future use. 
Note• In this manual, most illustrations shown are based on the KX-UTG200.
Outline   This manual briefly describes basic information about the installation of the unit.
Related Documentation
Operating Instructions Describes information about the installation and operation of the unit.  
Administrator...

Other Information/For Your Safety
2
Other Information
Open Source Software NoticeParts of this product use open source software. For details about the open source 
software, see the Operating Instructions.
Trademarks• Plantronics is a trademark or registered trademark of Plantronics, Inc.
•  Jabra is a registered trademark of GN Netcom A/S.
•  The Bluetooth
® word mark and logos are registered trademarks owned by 
the Bluetooth SIG, Inc. and any use of such marks by Panasonic System 
Communications...

For Your Safety
3
WARNIN G
General Safety
Do not disassemble this unit. Dangerous electrical shock could result. 
The unit must only be disassembled and repaired by qualified service 
technicians.
Never attempt to insert wires, pins, etc. into the vents or other holes of 
this unit.
To prevent possible fire or electric shock, do not expose this unit to rain or 
moisture.
Do not splash water on the AC adaptor or the power cord, nor get them 
wet. Doing so can result in fire, electric shock, or injury. If...

For Your Safety
4
If damage to the unit exposes any internal parts, immediately disconnect 
the cable or cord. If the power is supplied from the network to the SIP 
Phone [Power-over-Ethernet], disconnect the Ethernet cables. Otherwise, 
disconnect the AC adaptor cord. Then return this unit to an authorized 
service center.
This handset earpiece is magnetized and may retain small ferrous 
objects.
The use of excessive sound volume through earphones, headphones, or 
headsets may cause hearing loss....

For Your Safety
5
Placement
Care should be taken so that objects do not fall onto, and liquids are not 
spilled into, the unit. Do not subject this unit to excessive smoke, dust, 
moisture, mechanical vibration, shock, or direct sunlight.
Do not place heavy objects on top of this unit.
Place this unit on a flat surface.
Allow 10 cm (3 15/16 in) clearance around the unit for proper ventilation.
Wall Mounting
Make sure that the wall that the unit will be attached to is strong enough 
to support the unit....

For Your Safety/Important Safety Instructions
6
Wipe the unit with a soft cloth. Do not clean the unit with abrasive 
powders or with chemical agents such as benzine or thinner.
The handset hook poses a choking hazard. Keep the handset hook out of 
reach of children.
When left unused for a long period of time, disconnect the unit from 
the AC outlet. When the unit receives power from a PoE power supply, 
disconnect the Ethernet cables.
When the unit is mounted on a wall, make sure the cables are securely...

Accessory Information
7
Accessory Information
Included Accessories*1
Handset (1)Handset Cord (1)
[Part No.] 95.1204T00[Part No.]371.00447.005
Stand (1)Ethernet cable (1)
[Part No.]467.00209.005[Part No.]371.00473.005
*1 For extra orders for the accessories, call toll-free: 1-800-332-5368. 
Note• The illustrations may differ from the appearance of the actual product.
Optional Accessories
AC Adaptor• DSA-42D-48 2 480063 (P/N: 381.00398.005)
Wall Mount Kit• 
Add-on key module• KX-UTA336
KX-A433
DSA-48PFA-48...

Location of Controls
8
Location of Controls
Front View
For KX-UTG200:
AB
C D
E F G H I JK L M NO P Q R
C
For KX-UTG300:
4
11
D
F G H IJ KL MN O P Q RA
B  

Location of Controls
9
A	
Handset Hook
Keeps the handset stable when the unit is mounted on a wall. 
B	 LCD (Liquid Crystal Display)
KX-UTG200 is equipped with a 3.5-inch color LCD and LCD backlight.
KX-UTG300 is equipped with a 5.0-inch color LCD touch screen and LCD 
backlight.
C	 Flexible Buttons/Flexible Button Lamps (KX-UTG200 only)
Used to make or receive calls, or perform the feature that has been assigned 
to the button. The flexible button lamp shows the status of each flexible 
button.
D...

Installation and Setup
10Q	
REDIAL
Used to redial the last dialed number.
R	 HOLD
Used to put a call on hold.
Right Side View (for KX-UTG300)
A
B
A	 Add-on Key Module Slot Cover
Remove the Add-on key module slot cover when connecting an Add-on key 
module to the unit.
B	 USB Port
Connect a USB headset or other USB device.