Panasonic Kx Tg6591 Operating Instructions Manual

Voice mail service
V
oice mail is an automatic answering
service offered by your service provider/
telephone company. After you subscribe
to this service, your service provider/
telephone company’s voice mail system
answers calls for you when you are
unavailable to answer the phone or
when your line is busy. Messages are
recorded by your service provider/
telephone company, not your telephone.
Please contact your service provider/
telephone company for details of this
service.
Important:
R To use the...

Turning VM tone detection on/off
T
he default setting is  “On ”.
1 MMENU N#332
2 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N Listening to voice mail
m

essages
The unit lets you know that you have
new voice mail messages in the
following ways:
– “New Voice Mail ” is displayed on
the handset if message indication
service is available.
– The message indicator on the handset flashes slowly if the message
alert feature is turned on (“Message
alert”, page 40).
1 MVM N
or
M MENU N#330
R The...

Intercom
I
ntercom calls can be made:
– between handsets
– between a handset and the base unit
Note:
R If you receive an outside call while
talking on the intercom, you hear 2
tones.
– To answer the call with the
handset, press  MOFF N, then press 
M N
.
–

To answer the call with the base unit, press  MSP-PHONE N 2 times.
R When paging unit(s), the paged
unit(s) beeps for 1 minute. Making an intercom call
Handset
1 MM

ENUN a  M INT N
2 Mb N: Select the desired unit.  a
M SELECT N
R To stop paging,...

To establish a conference call:
M
M
ENU N a  M b N:  “Conference ”
a  M SELECT N
R To leave the conference, press
MOFF N. The other 2 parties can
continue the conversation.
R To put the outside call on hold: 
MMENU N a  M b N:  “Hold ” a
M SELECT N
To resume the conference: 
M MENU N a  M b N:  “Conference ”
a  M SELECT NBase unit
1 D

uring an outside call, press
M INTERCOM N.
R All registered handsets beep for 1
minute.
2 Wait for the paged party to answer.
RIf paged party does not answer,
press...

Wall mounting
N
ote:
R Make sure that the wall and the fixing
method are strong enough to support
the weight of the unit. Base unit
1
L

ead the AC adaptor cord and
telephone line cord through the hole
in the wall mounting adaptor in the
direction of the arrow. 2
T
uck the telephone line cord inside
the wall mounting adaptor ( A).
Connect the AC adaptor cord and
telephone line cord ( B). 3
I
nsert the hooks on the wall
mounting adaptor into holes   and
 on the base unit.
4
A
djust the adaptor to hold the...

5
Mount the unit on a wall then slide
down to secure in place. To remove the wall mounting adaptor
W

hile pushing down the release levers
( A ), remove the adaptor ( B). Charger
D

rive the screws (not supplied) into the
wall. 46
For assistance, please visit http://www.panasonic.com/helpUseful Information83 mm 
(31/4 inches)
or
102 mm 
(4 inches)
83 mm
(31/4 inches)102 mm
(4 inches)1
21
2 B
AA 25.4 mm
(1 inch)
Screws
Hooks  

Error messages
Display message Cause/solution
Base no power
o
r
No link. Re-connect
base AC adaptor. R
The handset has lost communication with the
base unit. Move closer to the base unit and try
again.
R Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.
R The handset’s registration may have been
canceled. Re-register the handset (page 31).
Busy RT
he called unit is in use.
ROther units are in use and the system is busy.
Try again later.
R The handset you are using...

Troubleshooting
I
f you still have difficulties after following the instructions in this section, disconnect
the base unit’s AC adaptor, then reconnect the base unit’s AC adaptor. Remove the
batteries from the handset, and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn
o
 n even after installing
charged batteries. R
Place the handset on the base unit or charger to
turn on the handset.
The unit does not work. RM
ake sure the batteries are...

Problem Cause/solution
I cannot register a handset
t o a base unit. R
The maximum number of handsets (6) is already
registered to the base unit. Cancel unused
handset registrations from the base unit (page 31). Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
B
attery charge is low. Fully charge the batteries
(page 10).
I fully charged the batteries,
b
 ut
–  still flashes,
–  is displayed, or
–

the operating time seems to be shorter. R
C
lean the battery ends ( ,  ) and the...

Problem Cause/solution
I cannot make long
d istance calls. R
Make sure that you have long distance service. Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d
 isplayed. R
You must subscribe to Caller ID service. Contact
your service provider/telephone company for
details.
R If your unit is connected to any additional
telephone equipment such as a Caller ID box or
cordless telephone line jack, plug the unit directly
into the wall jack.
R If you use a DSL/ADSL service, we...