Panasonic Kx Tg2346 Operating Instructions Manual

							Phone Book
Telephone System
For assistance, please call: 1-800-211-PANA(7262)41
Editing an Item in the Phone Book 
Erasing an Item in the Phone Book 
• To cancel erasing, press No after step 3.
1Press Phone book.
2Press Search.
3Scroll to the desired item by pressing [d] or 
[
B], then press Edit.
• To search for the item by initial, see page 39.
4Edit the name (p. 38), then press [d].
• If you do not need to change the name, press [d] 
then go to step 5.
5Edit the phone number, then press [d].
• If you do not need to change the number, press 
[
d] then go to step 6.
• Each time you press f, a digit is erased. To erase 
all of the digits, press and hold 
f.
6Press Save.
• To continue editing other items, repeat from step 3.
7Press [OFF].
1Press Phone book.
2Press Search.
3Scroll to the desired item by pressing [d] or 
[
B], then press Erase.
• To search for the item by initial, see page 39.
4Press Yes.
• To erase other items, repeat from step 3.
5Press [OFF].
Handset
Jane
345-6789
Erase     Edit
KL
Jane Walke|r
   =Next   Kfd gL
5553456789|
   =Next   PKfdL
Handset
Helen
555-777-8888
Erase     Edit
KL
Erase?
No         Yes
KL
PQQX13987YA.book  41 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							42
Intercom
Intercom calls can be made between the handset and the base unit.
Making Intercom Calls
From 
From 
Using this feature, you can also locate a misplaced handset.
1Press [HOLD/INTERCOM].
• The base unit will ring for 1 minute.
• To stop paging, press [OFF].
2When the paged party answers, start talking.
• You can switch to the speaker by pressing [s]. To 
switch back to the receiver, press [C].
3To disconnect the intercom, press [OFF].
1Press [LOCATOR/INTERCOM].
• The handset will ring for 1 minute.
• To stop paging, press [LOCATOR/INTERCOM].
2When the paged party answers, talk into the MIC.
3To disconnect the intercom, press [LOCATOR/INTERCOM].
During an intercom call:
• If you have difficulty hearing while using the handset speakerphone and base 
unit speaker, decrease the speaker volume by pressing VOLUME [
						

							Intercom
Telephone System
For assistance, please call: 1-800-211-PANA(7262)43
Answering Intercom Calls
When a handset is paged, it rings and the Ringer/Message Alert indicator flashes 
rapidly.
When the base unit is being paged, it rings.
1Press [C], [s] or [HOLD/INTERCOM].
• You can also answer a call by pressing any button 
except [
d], [B] or [OFF].
2To disconnect the intercom, press [OFF].
1Press [LOCATOR/INTERCOM].
2To disconnect the intercom, press [LOCATOR/INTERCOM].
• When the ringer volume is turned off (p. 17, 18), the handset and the base unit 
will ring at the low level for intercom calls.
• You cannot change the ringer tone for intercom calls.
Handset
Call from Base
Base Unit
PQQX13987YA.book  43 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							44
Special Features
Te m p o r a r y  To n e  D i a l i n g
(For Rotary or Pulse Service Users) 
Press [*] (TONE) before entering access numbers which require tone dialing.
• The dialing mode changes to tone. You can enter numbers to access an 
answering service, electronic banking service, etc. When you hang up, the dialing 
mode will return to pulse.
Muting Your Conversation 
During a call, you can mute your phone so the other party cannot listen to you. 
When muting your conversation, you can hear the other party.
Press Mute.
•“Mute” will flash.
•To release the mute, press Mute again.
• If you press [C] or [s] to switch between the receiver 
and speaker, the mute will be released.
For Call Waiting Service Users 
Press [FLASH/CALL WAIT] if you hear a call waiting tone during a conversation.
• The first call is put on hold and you can answer the second call.
• To return to the first caller, press [FLASH/CALL WAIT] again.
• Call Waiting service cannot be used when the first call is put on hold, or the 
Answering System is handling a call.
• If this function does not operate properly, consult your telephone company for 
details.
Call Waiting Caller ID display 
If you subscribe to both Caller ID and Call Waiting with 
Caller ID services (CWID), when a second call is received 
while talking, the second caller’s information will be 
displayed. After you hear a call waiting tone while talking, 
the display shows the caller’s name with the phone number and 
“----Waiting-----”. 
• Contact your telephone company for details about availability in your area, and to 
verify that CWID is activated on your telephone line.
• The caller’s information will only be shown on the display of the handset which is 
on the outside call.
• The second caller’s name will not be announced even if the Talking Caller ID 
feature is on (p. 30).
Handset
Handset
Talk
00-00-30
(VE)      Mute
KL4 0
Handset
BROWN,NANCY
1-555-666-7777
----Waiting-----
PQQX13987YA.book  44 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							Special Features
Telephone System
For assistance, please call: 1-800-211-PANA(7262)45
Using the PAUSE Key
(For PBX Line/Long Distance Calls) 
We recommend you press Pause or P if a pause is 
required for dial with a PBX or to make a long distance call.  
Ex. Line access number [9] (PBX)
[9] N Pause or 
P N 
• Pressing Pause or P once creates a 3.5 second pause. 
This prevents misdialing when you dial after confirming 
the entered number (p. 26) or dial a stored number
(p. 39, 40).
• Pressing Pause or P more than once increases the length of the pause between 
numbers.
FLASH Button 
Pressing [FLASH/CALL WAIT] allows you to use special features of your host PBX 
such as transferring an extension call, or accessing optional telephone services 
such as call waiting. 
• Pressing [FLASH/CALL WAIT] cancels Temporary Tone Dialing mode or the 
mute (p. 44).
Selecting the flash time
The flash time required depends on your telephone exchange or host PBX. 
You can select the following flash times: “700, 600, 400, 300, 250, 110, 100 or 
90 ms (milliseconds)”. The factory preset is “700 ms”.
• If PBX functions do not work correctly, consult your PBX supplier for the correct 
settings.  
1Press [MENU].
2Scroll to “Initial setting” by pressing [d] 
or [
B], then press Select.
3Scroll to “Set tel line” by pressing [d] or 
[
B], then press Select.
4Scroll to “Set flash time” by pressing [d] 
or [
B], then press Select.
5Select the desired time by pressing [d] or [B].
6Press Save, then press [OFF].
Handset
OR Examp
le
9P15556667777|
Clear    PauseKL
9P15551234567|
   =Next   PKfdL
Phone number
Handset
Initial setting
Back  SelectKdBL
Set tel line
Back  SelectKdBL
Set flash time
Back  SelectKdBL
Set flash time
:700ms
Back     Save
KdBL
PQQX13987YA.book  45 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							Special Features
46
Incoming Call Tone   
During an intercom call (p. 42), you can be informed of incoming calls by two tones. 
If this feature is turned on, incoming call tones will be heard for as long as the line is 
ringing. If this feature is set to “2”, incoming call tones will be heard only 2 times. 
If this feature is turned off, no tones will be heard. The factory preset is “2”. 
Using the handset, this feature can be set separately for the handset and base unit.
Handset incoming call tone 
Base unit incoming call tone  1
Press [MENU].
2Scroll to “Ringer setting” by pressing [d] 
or [
B], then press Select.
3Scroll to “Incoming call.” by pressing [d] 
or [
B], then press Select.
4Select “On”, “Off” or “2” by pressing [d] or 
[
B].
5Press Save, then press [OFF].
1Press [MENU].
2Scroll to “Initial setting” by pressing [d] 
or [
B], then press Select.
3Scroll to “Set base unit” by pressing [d] or 
[
B], then press Select.
4Scroll to “Incoming call.” by pressing [d] 
or [
B], then press Select.
5Select “On”, “Off” or “2” by pressing [d] or 
[
B].
6Press Save, then press [OFF].
HandsetBase Unit
Handset
Ringer setting
Back  SelectKdBL
Incoming call.
Back  SelectKdBL
Incoming call
tone :2
Back     Save
KdBL
Handset
Initial setting
Back  SelectKdBL
Set base unit
Back  SelectKdBL
Incoming call.
Back  SelectKdBL
Incoming call
tone :2
Back     Save
KdBL
PQQX13987YA.book  46 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							Special Features
Telephone System
For assistance, please call: 1-800-211-PANA(7262)47
Key Tone 
You can select whether or not the handset keys will sound tones (key tone, 
confirmation tone, error tone). The factory preset is ON. 
Re-registering the Handset 
If “No link to base. Move closer to base, try again.” is displayed 
even when using the handset near the base unit, the handset may have lost 
communication with the base unit. You need to re-register the handset to the base 
unit.
• Make sure the base unit is not being used.
• Have both the handset and base unit nearby during registration. 
• Follow steps 1 and 2 listed below. You have about 1 minute to complete 
them. 
• If the handset beeps 3 times and “Error!!” is displayed, an error occurred. Try 
again from step 1.
• You can stop registration by pressing [OFF] on the handset, and pressing 
[LOCATOR/INTERCOM] on the base unit.
1Press [MENU].
2Scroll to “Initial setting” by pressing [d] 
or [
B], then press Select.
3Scroll to “Key tone” by pressing [d] or [B], 
then press Select.
4Select “Off” or “On” by pressing [d] or [B].
5Press Save, then press [OFF].
1Base unit:Press and hold [LOCATOR/INTERCOM] until a beep sounds.
• The CHARGE indicator flashes.
2Handset:Press and hold [FLASH/CALL 
WA I T] until “Handset 
Registering” is displayed.
• When registration is complete, a beep sounds 
from the handset. 
•Wait for 20 seconds after registration is 
complete while the handset establishes 
communication with the base unit.
Handset
Initial setting
Back  SelectKdBL
Key tone
Back  SelectKdBL
Key tone
:On
Back     Save
KdBL
Handset & Base Unit
Handset
  Registering
Handset [1]
   Registered
PQQX13987YA.book  47 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							48
Automatic Answering Operation
When the unit answers a call, a greeting message is played and the caller’s 
message is recorded.  
Setting the Unit to Answer Calls 
Press [ANSWER ON] to turn on the Answering System.
• The indicator lights and the unit announces “Answer 
set” and current day and time. If “Answer set. Set 
time” is heard, set the date and time (p. 14).  
• The unit will announce the remaining recording 
time if it is less than 3 minutes. 
• When no recording time is available, you will 
need to erase any unnecessary messages before 
new messages can be recorded (p. 53). The unit 
can indicate that memory is full in the following 
ways:
— “ ” will flash on the base unit and the  
ANSWER ON indicator will flash rapidly until 
you erase a message.
— The unit will announce “Memory full” when you 
press [ANSWER ON], [GREETING REC], or 
[MEMO], and after playing back messages or recording a message.
• If you do not want the unit to answer calls, press [ANSWER ON] again to turn off 
the Answering System. The indicator light goes out and “Answer off” is heard.
• You can also turn on the Answering System remotely from an outside phone 
(p. 58).
• If you subscribe to Caller ID (p. 29), Caller ID information automatically adjusts the 
date and time when a call is received, provided you have already set the date and 
time manually (p. 14).
• To turn the Answering System off, press [0] in step 3. “Answer off” is heard. • The total recording time of all messages (greeting, incoming and memo) is 
about 16 minutes. If messages are recorded in noisy rooms, the time may be 
shortened by up to 3 minutes.
• To select the caller’s recording time, see page 22.
• A maximum of 64 messages (including greeting and memo message) can be 
recorded.
1Press [MENU].
2Press Select at “Message play”.
3Press [8] to turn on the Answering System.
•“Answer set” is heard.
4Press [OFF].
Base Unit
[ANSWER ON] and Indicator
FULL
Handset
PQQX13987YA.book  48 ページ  ２００４年２月５日　木曜日　午前９時３分 
						

							For assistance, please call: 1-800-211-PANA(7262)49
Automatic Answering Operation
Answering System
Monitoring Incoming Calls 
While a caller is leaving a message, you can monitor the call through the base unit 
speaker. 
• To increase the speaker volume while monitoring, press VOLUME [>]. 
To decrease the volume, press VOLUME [
						

							50
Listening to Messages
Using the Base Unit 
You can see the total number of recorded messages on the base unit display. If the 
NEW MESSAGE indicator flashes on the base unit, new messages have been 
recorded. 
To play back messages 
Press [MESSAGE].  
• The unit announces the number of new 
messages and only new messages are 
played back.
• When you have no new messages, the unit 
announces “No new messages. All message 
playback” and plays back all messages.
• When you have no messages, the unit 
announces “No messages”.  
• During playback, the display shows the message number.
• At the end of the last message, “End of final message” is heard. The unit will 
announce the remaining recording time if it is less than 3 minutes.
Voice Day/Time Stamp: During playback, the unit will announce the day and 
time when each message was recorded (p. 14).
Base Unit
[MESSAGE] NEW MESSAGE Indicator
PQQX13987YA.book  50 ページ  ２００４年２月５日　木曜日　午前９時３分