Panasonic Kx Tg2257 Operating Instructions Manual

71
Answering System
For assistance, please call: 1-800-211-PANA(7262)
ERASING A
SPECIFIC
MESSAGE
(During playback)
ERASING ALL
MESSAGES
ANSWERING
SYSTEM OFF
(0)
•The current message is erased.
•A short beep will sound and the next
message will be played.
•All recorded messages are erased.
•A long beep sounds and “No messages” is
heard.
•The unit hangs up and will not answer
calls until turned on again.
Turning on the answering system
Call your unit and wait for 15 rings.
•The unit will answer and the...

72
Remote Operation with the Handset
Voice menu
If no commands are entered after you press
(FLASH/CALL!WAIT/PLAYBACK), the unit will start the following voice
menu.
“Press 4 to play back new messages. Press 5 to play back all messages.”
•You can enter direct commands even if the voice menu has started.
You can operate your answering system
with the handset. 
The announcements and recorded
messages can only be heard with the
handset.
Summary of remote operation
Press (FLASH/CALL!WAIT/PLAYBACK).
•The...

73
Answering System
Direct commands
For assistance, please call: 1-800-211-PANA(7262)
NEW MESSAGE
PLAYBACK
ALL MESSAGE
PLAYBACK
REPEAT 
(During playback)
SKIP
(During playback)
CHANGING
PLAYBACK
SPEED
(During playback)
STOP
ERASING A
SPECIFIC
MESSAGE
(During playback)
ERASING ALL
MESSAGES
ANSWERING
SYSTEM OFF
ANSWERING
SYSTEM ON(4)
(5)
(1)
(2)
(9)
(*) (4)
(*) (5)•Only new messages are played back.
•All messages are played back.
•The current message is repeated.
•If you press within 5 seconds of
playback,...

74
Wall Mounting
This unit can be mounted on a wall phone plate.
2
Connect the AC adaptor.
3
Tuck the telephone line cord inside
the wall mounting adaptor, then
push it in the direction of the arrow.
•The word “UP” should face upward.
1
Push the hook and turn it around.
Turn the hook until a click is heard.
To Power
Outlet 

75
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
•Fasten the telephone line cord to
prevent it from being disconnected.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The IN USE/CHARGE indicator lights.
2
1
Hook
Hole
Hooks
OR 

76
H
You can hang the handset on your belt or pocket using the belt clip.
To attach the belt clip To remove the belt clip
Headset JackThe illustration headset
is a KX-TCA88.
Connecting an optional headset to the handset
Open the headset jack cover, and connect an optional headset to the
headset jack as shown below.
Belt Clip
Plugging an optional headset into the handset allows a hands-free phone
conversation. Please use only a Panasonic KX-TCA88 or KX-TCA90
headset. To order, call the accessories...

77
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery. If “Recharge” is displayed and/or “ ” flashes after being fully
charged, replace the battery with a new Panasonic...

78
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord 

79
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
“No link to base
Place on cradle and
try again.” is displayed
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset and/or the base
unit does not ring.
The handset display is
blank.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the unit starts to
ring and stops the program/
search.
You cannot make a call with
the handset....

80
Troubleshooting
Problem
The unit does not display the
caller’s name and/or phone
number.
The handset display exits
the Caller List.
When a second call is
received during a
conversation, the unit does
not display the new caller’s
name and/or phone number.
You cannot page the
handset.
You cannot redial by
pressing 
(REDIAL/PAUSE).
You pressed (CALLER!IQ)in
the talk or speakerphone
mode.
Remedy
•You need to subscribe to a Caller ID
service.
•Other telephone equipment may be
interfering with your phone....