Panasonic Kx Tg2247 Operating Instructions Manual

71
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
•Fasten the telephone line cord to
prevent it from being disconnected.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The IN USE/CHARGE/HOLD indicator
lights.
2
1
Hook
Hole
Hooks
OR 

72
H
You can hang the handset on your belt or pocket using the belt clip.
To attach the belt clip To remove the belt clip
Headset JackThe illustration headset
is a KX-TCA88.
Connecting an optional headset to the handset
Open the headset jack cover, and connect an optional headset to the
headset jack as shown below.
Belt Clip
Plugging an optional headset into the handset allows a hands-free phone
conversation. Please use only a Panasonic KX-TCA88 or KX-TCA90
headset. To order, call the accessories...

73
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery. If “Recharge” is displayed and/or “” flashes after being fully
charged, replace the battery with a new Panasonic...

74
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord 

75
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
“No link to base
Place on cradle and
try again.” is displayed
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The unit does not ring.
The handset display is
blank.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the unit starts to
ring and stops the program/
search.
You cannot make a call with
the handset.
Remedy
•You are too far...

76
Troubleshooting
Problem
The unit does not display the
caller’s name and/or phone
number.
The handset display exits
the Caller List.
When a second call is
received during a
conversation, the unit does
not display the new caller’s
name and/or phone number.
You cannot page the
handset.
You cannot redial by
pressing 
(REDIAL/PAUSE).
You pressed (CALLER!IQ)in
the talk or speakerphone
mode.
Remedy
•You need to subscribe to a Caller ID
service.
•Other telephone equipment may be
interfering with your phone....

77
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
The answering system is on,
but incoming messages are
not recorded.
You cannot listen to the
recorded messages.
“” is displayed and the
ANSWER ON indicator
flashes rapidly, and no new
messages are recorded.
You cannot operate the
answering system with the
base unit.
You cannot operate the
answering system from a
touch tone phone.
FULL
Remedy
•The recording time is set to “Greeting
only”. Select “1 minute”, “2 minutes” or 
“3...

78General
Problem
The unit does not work.
You cannot program items,
such as the dialing mode.
Remedy
•Check the settings (p. 13–17).
•Charge the battery fully (p. 14).
•Clean the charge contacts and charge
again (p. 15).
•Install the battery properly (p. 14).
•Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.
•Re-install the battery and place the
handset on the base unit (p. 73). Try
again.
•Programming is not possible while the
unit is in the talk or...

79
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
Previously programmed
information is erased.
“Recharge” is displayed,
“” flashes or the unit
beeps intermittently.
You charged the battery
fully, but “Recharge” is still
displayed and/or “”
continues to flash.
The IN USE/CHARGE/
HOLD indicator light does
not go out after the battery
has been charged.
If you cannot solve your
problem
After Caller IQ is turned to
off, the unit is unable to turn
it back on and LCD shows 
“Listen &...

80
openLCR Service for Caller IQ Feature
The Caller IQ feature is compatible with service provided by openLCR.
Important:
•If you have any questions regarding the openLCR service, call
openLCR’s customer service department at 1-866-openLCR 
(1-866-673-6527).
•NEITHER KYUSHU MATSUSHITA ELECTRIC CO., LTD. (KME) NOR
MATSUSHITA ELECTRIC CORPORATION OF AMERICA (MECA) IS IN
ANY WAY AFFILIATED WITH, OR RESPONSIBLE FOR THE ACTS OR
OMISSIONS OF, OPENLCR.COM, INC. (OPENLCR). NEITHER KME
NOR MECA NOR ANY OF THEIR...