Panasonic Kx Tc1851 Operating Instructions Manual

“
41
Advanced Operation
To erase a stored number
Press and hold (CLEAR)in step 6 on page 40.
≥You can exit the programming mode any time by pressing (FUNCTION/EXIT/CH).
Setting the Voice Mail Tone
If your voice mail service sends a voice mail tone after a new message
has been recorded, set to “On”. “Voicemail” and “” will be displayed
when a message has been recorded in your mailbox. You will hear a
series of voice mail tones followed by a dial tone after pressing 
(TALK).
(Contact your service provider...

“Voice Mail Service
42
Listening to Voice Mail Messages
After receiving a voice mail message, “Voicemail” and “” will be
displayed. To listen to your voice mail message(s), follow the steps below.
1
Press (FUNCTION/EXIT/CH).
2
Press (›)or (‹)repeatedly until the arrow
points to “Voicemail dial”.
3
Press FWD/EDIT(fl)(Yeskey).
≥The stored voice mail access number is
displayed (p. 40).
4
Press (TALK).
≥The unit automatically dials the access
number.
5
Follow the pre-recorded instructions.
6
When finished,...

Special Features“
43
Advanced Operation
Automatic Security Code Setting
Each time you place the handset on the base unit, the unit automatically
selects one of more than a million security codes. These codes help
prevent the unauthorized use of your telephone line by another cordless
telephone user.
Handset Locator
You can locate the handset or page the handset user with beep tones
from the base unit.
1
Press (HANDSET\LOCATOR).
≥The IN USE/CHARGE indicator flashes. The handset beeps for 1 minute
and...

44
“Special Features
For Call Waiting Service Users
Press (FLASH/CALL\WAIT)if you hear a call-waiting tone while talking.
≥The first call is put on hold and you can answer the second call.
≥To return to the first caller, press (FLASH/CALL\WAIT)again.
≥If this function does not operate properly, consult your telephone company for
details.
Call Waiting Caller ID Feature
Call Waiting Caller ID Feature allows your
handset to display the second caller’s
information. After you hear a call-waiting tone
while...

45
Advanced Operation
FLASH Button
Pressing (FLASH/CALL\WAIT)allows you to use special features of your
host PBX such as transferring an extension call or accessing special
telephone services (optional) such as call waiting.
Selecting the flash time
The flash time depends on your telephone exchange or host PBX. 
You can select the following flash times: “700, 600, 400, 300, 250, 110,
100 or 90 ms (milliseconds)”. Your phone comes from the factory set to
“700 ms”.
Make sure the handset is in the standby...

46
Wall Mounting
This unit can be mounted on a wall phone plate.
1
Set the handset holder as shown.
2
Connect the AC adaptor.
3
Tuck the telephone line cord inside
the wall mounting adaptor, then
push it in the direction of the arrow.
≥The word “UP” should face upward.
To Power 
Outlet
1229:#.~
 
 
 
 1.
 
 

47
Useful Information2
1
OR
4
Connect the telephone line cord. 
Mount the unit, then slide down.
≥Raise the antenna.
5
To charge the handset
battery:
Place the handset on the
handset holder as shown.
≥The IN USE/CHARGE
indicator lights.
To remove the handset holder
While pressing the arrow (1) and opposite side (2) of the holder, pull out
the handset holder.
1229:#.~
 
 
 
 1.
 
 

48
If “Recharge battery” is displayed and/or “” flashes after being
fully charged, replace the battery with a new Panasonic P-P508 battery.
To order, call the accessories telephone number on page 2.
1
Remove the cover by sliding
while pressing the arrow.
2
Replace the battery and close the
cover.
3
Make sure you charge the new
battery for about 6 hours in order
to display the battery strength
prompt correctly (p. 11).
Attention:
The product you have purchased is powered by a nickel
cadmium battery which...

49
Useful Information
Before Requesting Help“
Problem
“No link to base.
Place on cradle and
try again.” is displayed
and an alarm tone sounds.
The unit does not work.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset does not ring.
The handset display is
blank.
The handset display is still
blank after pressing 
(›),
(‹), BACK(fi)or FWD/EDIT
(fl)
.
Remedy
≥You are too far from the base unit. Move
closer and try again.
≥Place the handset on the base unit and
try again....

50
“Before Requesting Help
Problem
You cannot program items,
such as the dialing mode.
Previously programmed
information is erased.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the unit starts to
ring and stops the program/
search.
The unit does not display
the caller’s name and/or
phone number.
The display goes to the
standby mode while viewing
the Caller List.
When a second call is
received during a
conversation, the unit does
not display the new caller’s...