Panasonic Kx T206e Installation Manual

							11
System Connection Diagram
P
a
n
a
s
o
n
i
cPanasonicA
U
T
O
 
S
C
A
NAUTO SCAN10CH10CH
P
a
n
a
s
o
n
i
cPanasonic
PanasonicPanasonicELECTRONICMODULARSWITCHINGSYSTEM
2 CO Lines
Doorphone KX-T30865
Doorphone
6 Extensions
(one pair)
(two pair)(two pair)
(two pair)
(one pair) (one pair)KX-T7130
KX-T7050 Single Line Telephone
Cordless Phone
Telephone Answering
Machine with FacsimileKX-T7020to CO1 and CO2
Door Opener 
						

							12
CO Line Connection
Wire SpecificationThe wire specifications are as follows:
WireSolid wire
Diameter of conductorø 0.4 – ø 0.65mm
Diameter with coatingø 0.66 – ø 1.05mm
ConnectionUse a 4-pin plug (included) to connect CO lines.
A single plug is able to connect two CO lines.  Use twisted pair cable.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert the wires all the way into the plug.
GROUND
SYSTEM
EXTN.
5
EXTN.
3
EXTN.
1
CO 2
CO 1
EXTN.
6
EXTN.
4
EXTN.
2
DPH
DOOR
OPENER
A
A B
B
CO 2
CO 1CO 2
CO 1
To Modular Jacks from
the Central Office
A
B
CO 2
A
BCO 1
CO 2
CO 1
Note
•You can use cable holders to fix the wires. 
						

							13
Extension Connection
Wire SpecificationThe wire specifications are as follows:
WireSolid wire
Diameter of conductorø 0.4 – ø 0.65 mm
Diameter with coatingø 0.66 – ø 1.05 mm
ConnectionUse a 4-pin plug (included) to connect extension lines.
There are 6 plugs to connect extensions to EXTN. 1 through EXTN. 6
jacks.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert the wires all the way into the plug.
H
A
B
L
A
B
For a proprietary telephone
For single line telephones
GROUND
SYSTEM
EXTN.
5
EXTN.
3
EXTN.
1
CO 2
CO 1
EXTN.
6
EXTN.
4
EXTN.
2
DPH
H
B A
L
EXTN.
1
DOOR
OPENER
To extensions
Notes
•A facsimile must be connected to EXTN.6 jack if an optional DISA/FAX Detect card (KX-
T20691) is installed.  See page 16 to install the card.  System programming is also required.
The “#12 Fax Connection” program should be assigned as “ENABLE”.  See page 25.  The
“#24 Call Incoming Mode Selection” program should be assigned as “DISA”.  See page 28.
•The EXTN.1 through EXTN.6 jacks correspond to extension numbers 21 through 26 respec-
tively.
•You can use cable holders to fix the wires. 
						

							14 Any single line telephone can be connected in parallel with a proprietary telephone.
ELECTRONICMODULARSWITCHINGSYSTEMP
O
W
E
R
Paralleled Telephone Connection
Notes
• The following features are not available for SLT connected in parallel:
Call Splitting
External Feature Access
Conference
4-conductor wiring cord
Connect pins “H”, “A”,
“B”, and “L”.2-conductor wiring cord
Connect pins “A” and “B”.
Master
socket Secondary
socket 
						

							15
Installation of Optional Card and Unit
Doorphone (KX-T30865) Connection
2-conductor wiring cord
KX-T30865
Notes
•The doorphone adaptor is not required for KX-T206.
•To avoid howling, you must assign all extensions as “DISABLE” in the “#06/#76 Doorphone
Assignment (Day/Night)” program when you do not connect a doorphone.
•If howling occurs while using the doorphone feature, check the wiring.
•You can use cable holders to fix the wires.
Door Opener Connection
A user-supplied door opener can be connected to the system.
GROUND
EXTN.
5
EXTN.
3
EXTN.
1
CO 2
CO 1
EXTN.
6
EXTN.
4
EXTN.
2
DPH
DOOR
OPENER
SYSTEM
3. Wind and fix the cables of the door opener
round the upper cable holder. 1. Loosen the screws. 2. Insert the wires coming from the door
opener into holes and tighten the screws.
DOOR
OPENER
Notes
•For wiring, it is recommended to use UL1015 twisted wire or the equivalent.
•The wire should be between 1.2 and 2.4 mm in diameter including the coating.
GROUND
SYSTEM
EXTN.
5
EXTN.
3
EXTN.
1
CO 2
CO 1
EXTN.
6
EXTN.
4
EXTN.
2
DPH
B A
P
a
n
a
s
o
n
i
cPanasonic
DPH
DOOR
OPENER
D=1.2–2.4 mm
GROUND
EXTN.
5
EXTN.
3
EXTN.
1
CO 2
CO 1
EXTN.
6
EXTN.
4
EXTN.
2
DPH
DOOR
OPENER
SYSTEM
To the door opener
•Set the door opener paired with the doorphone. 
						

							16
DISA Card (KX-T20691) Connection
1. Disconnect the AC cord from the system.
2. Loosen the screws and remove the cover.3. Attach the DISA card to the marked connectors.
4. Replace the cover and secure the screws.
5. Connect the AC cord again.
CO2
CO 1
DOOR
PHONE
GROUND
EXTN.
5
EXTN.
3
EXTN
1E
X
T
N
.
6
E
X
T
N
.
4
E
X
T
N
.
2
D
P
H
P
O
W
E
R
ELECTRONIC MODULAR SWITCHING SYSTEM
The DISA feature allows an outside caller to have direct access to intercom calls.  System pro-
gramming is required.  See “#10 OGM Recording” on page 24 and “#24 Call Incoming Mode
Selection” on page 28.
Keep the following conditions in mind:
•When a caller enters the second digit of an extension number (1 through 6) during the mes-
sage, he/she can reach the extension directly.
•If the call is not received, the assigned extensions will ring.  See “#04/#74 CO1 Ringing
Assignment (Day/Night), “#05/#75 CO2 Ringing Assignment (Day/Night)” on page 22 and
“#60 DISA Ringing Time” on page 29.
•If the caller enters 0, the assigned extensions can receive his/her call.  See “#04/#74 CO1
Ringing Assignment  (Day/Night), “#05/#75 CO2 Ringing Assignment (Day/Night)” on page
22.
•If the caller enters 7, 8 or 9, or enters nothing, extension 21 will receive his/her call.
•Any calls from a rotary phone will be received by extension 21.
Installation of Optional Card and Unit 
						

							17
Installation of Lightning Protectors
Overview
A lightning protector is a device to be installed on a CO line to prevent a dangerous surge from
entering the building and damaging equipment.
A dangerous surge can occur if a telephone line comes in contact with a power line.  Trouble due
to lightning surges have been showing a steady increase with the development of electronic
equipment.
In many countries, there are regulations requiring the installation of a lightning protector.
A lightning strike to a telephone cable which is 10 m above ground can be as high as 200,000
volts.
This system should be installed with lightning protectors.
In addition, grounding (connection to earth ground) is very important for the protection of the
system.
Installation
CO CO CO
EXTN
EXTN
Frame
Earth EXTN
SLT PT
EarthMain
Distribution 
FrameMain Unit
Earth Terminal
Lightning
Protectors 
						

							18
Installation of an Earth Rod
Notice
If you install an extension outside of the main building, the following precautions are recom-
mended:
(1) Install the extension wire underground.
(2) Use a conduit to protect the wire.
Note
•The lightning protector for an extension is different from that for CO.
(1) Installation location of the earth rod ...... Near the protector
(2) Check obstructions ................................ None
(3) Composition of the earth rod ................. Metal
(4) Depth of the earth rod ............................ More than 50 cm
(5) Size of the earth wire ............................. Thickness is greater
than 1.6 mm
Notes
•The above figures are recommendations only.
•The length of earth rod and the required depth depend on the
composition of the soil.
Installation of Lightning Protectors
Outside
EarthSLT
PT
EXTNEXTN
EXTN EXTNCO CO COProtectors
(Another Building) (Main Building)
Main
Distribution 
FrameMain
UnitLightning
Protector
TEL TEL
Lightning
Protector
Main
Unit
(Underground)
Earth Rod Earth WireCO 
						

							19
Power Failure Transfer
In the event of a power failure, CO2 is connected to extension 22 automatically.
Note
•The system programmed data is protected by the factory provided lithium battery.
Starting the System
Plug the AC power cord into the system and an AC outlet.
•The power indicator of the system will light. 
						

							20
General Programming Instructions
Default SettingThis system has a default factory setting.  If any of the program-
ming needs to be changed, you can change the setting by system
programming.
Required Telephone SetYou can use any of the following telephones for system program-
ming:
• Proprietary Telephone (PT): KX-T7130, KX-T7020, KX-T7050
• Single Line Telephone (SLT): tone type
All telephones (except KX-T7130) do not have display panels, so
you cannot check the setting you have made.  Therefore, please use
KX-T7130 to check the programming.
Extensions Used forSystem programming can only be performed from extension 21.
Programming
To Check theUse KX-T7130.  When you check the assignment, set the
Programmed DataMEMORY switch on PT to “PROGRAM”.
Enter “#” and the program address.
You cannot check programs #60, #62, #63, #65, #67, #84 and #85,
as they are not displayed on the display panel.
Before ProgrammingTo enter the system programming mode:
After ProgrammingTo exit the system programming mode:
662020[Off-hook]
6620[Off-hook]
6