Panasonic KX P7110 User Manual

 
Upgrade Options
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
5 
2 
Slide the option cover and remove it. 
3 
Remove the two screws, then remove the metal plate.
# $
Downloaded From ManualsPrinter.com Manuals 

 
Upgrade Options
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
6 
4 
Connect the optional board to the following connector as illustrated
below. 
5 
Install the metal plate in the printer. 
6 
Fasten the metal plate with the two screws removed earlier.
CN1
Upgrade kit
CN2RAM board
#
$
Downloaded From ManualsPrinter.com Manuals 

 
Upgrade Options
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
7 
7 
Install the option cover. 
8 
Plug in the power cord and reconnect any cables to the back of the
printer.
Downloaded From ManualsPrinter.com Manuals 

 
Upgrade Options
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
8 
If you install the RAM board, set the printer driver for the printer’s installed memory (see
“Setting the Device Options” below).
If you install the Upgrade Kit (for PostScript), install the printer driver for PostScript and set it.
To install the printer driver for PostScript in Windows or Macintosh, refer to the Setup Guide.
To set the printer driver in Windows, see  “Setting the Printer Driver for...

 
Upgrade Options
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
9 
n 
Setting the Printer Driver for PostScript in Windows 
It is possible to set the printer by using the printer properties window. It can be displayed from
Windows (see below) or from an application. To display the printer properties window from an
application, select the Panasonic KX-P7105 PS or Panasonic KX-P7110 PS printer in the print
window and click Properties.
When setting the printer by using the...

 
Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
10 
Periodic cleaning of the printer is recommended. The frequency of cleaning is dependent
upon the environment in which the printer is used.
You should clean the printer:
• at least once a month.
• when you replace the toner cartridge.
• when print quality has deteriorated. 
CAUTION 
• Do not use benzene, thinner, aerosol cleaners, or any abrasive powder. 
1 
Turn the power OFF. 
2 
Clean all the covers...

 
Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
11 
3 
While rotating the pick up roller, wipe it with a soft cloth that has been
moistened with a mild commercial cleaner. 
4 
Open the front cover. 
5 
Lift the drum unit up (  
# 
 ) and slide it out of the printer (  
$ 
 ). 
•To avoid possible toner spillage, it is recommended to place the drum unit on a
newspaper or drop cloth.
Pick up roller
#
$
#
Downloaded From ManualsPrinter.com Manuals 

 
Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
12
SAFETY CAUTION 
• It is very hot inside the printer; to avoid personal injury, do not touch the components
illustrated below. 
CAUTION 
• To prevent any damage to the drum unit, observe the following precautions.
— Do not touch the black drum surface illustrated below. 
— Do not expose the drum unit to light for more than 5 minutes.
— Do not expose the drum unit to direct sunlight.
— Do not keep the drum...

 
Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.
 
13
6Wipe rollers (A) and (B), and paper chute with a soft cloth that has been
moistened with a mild commercial cleaner.
•Be sure to remove the paper dust.
NOTE
• Front rollers (A) can be rotated half. Inner rollers (B) can be rotated to the direction of the
arrow. Be sure not to damage the sheets in front of the inner rollers (B).
7Turn the sponge up and carefully wipe the laser unit cover glass with a
dry...

Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.14
8Carefully wipe the corona wire of the drum unit by sliding a dry cotton
swab from end to end a few times.
9Firmly insert the drum unit in the slot of the printer ( # ) [insert the side
pins of the drum unit into the groove (label  )]. Push down ( $ ). 
10Close the front cover and replace the media tray into the printer.
corona wire
$
$
#
Side pin
Downloaded From ManualsPrinter.com Manuals