Panasonic Hybrid Control Panel Aw Rp501 Operating Instructions

-9-
@6Lens Iris Control [IRIS, LEVEL]
When IRIS AUTO/MANU Switch @5is in the MANU
position, the iris can be controlled over the range from
the closed position to the fully open position using this
control.  Turning it clockwise opens the iris and turning
it counterclockwise closes the iris.
If the camera is preset to AUTO IRIS ADJ ON when
IRIS AUTO/MANU Switch @5is in the AUTO position,
this control may be used for fine adjustment of ALC
focus level.  For details, refer to the Operating
Instructions for...

-10-
#0Defroster Switch [DEF, ON/OFF]
If this switch is connected to a pan/tilt head with a
built-in defroster function, it switches on and off the
defroster.
#1Wiper Switch [WIP, ON/OFF]
If this switch is connected to a pan/tilt head with a
built-in wiper function, it switches on and off the wiper.
#2Heater/Fan Switch [H/F, ON/OFF]
If this switch is connected to a pan/tilt head with a
built-in heater or fan function, it switches on and off the
heater or fan.
#3Lens Extender Switch [EXT, ON/OFF]
If this...

-11-
#8Pan/tilt Lever [PAN/TILT, UP/DOWN/LEFT/RIGHT]
Controls the head’s pan/tilt operation at varying
speed depending on the angle of the lever.  The
pan/tilt head turns up when the lever is moved
toward UP, or down when it is moved toward DOWN,
provided that TILT REVERSE Switch %4is in the NOR
position.  The pan/tilt head moves in the opposite
direction if the TILT REVERSE Switch %4is in the REV
position.  The pan/tilt head turns leftward when the
lever is moved toward LEFT, or rightward when it is...

-12-
n REAR PANEL
TALLY
HOT DC12V IN
AUX  CONTROL  IN
VIDEO  IN OUT G/L  OUTVIDEO OUT 1 VIDEO OUT 2
CONTROL CONTROL  OUTPAN/TILT CAMERA
TO CAMERA PAN/TILT HEADG / L  IN
S-VIDEO OUT
#9TALLY Input Terminal [TALLY] 
(2-pin Terminal Board)
Connect it to the tally connector on a special effect
generator (SEG) or a video switcher, for example.
When [HOT] terminal falls to ground level, TALLY
Indicator @2and the tally indicator on the Pan/tilt Head
(AW-PH300) light red.
$012V DC Input Connector [DC 12V IN] (DC...

-13-
   1      +5V
   2      ZOOM
   3      FOCUS
   4      TILT
   5      PAN
   6      GND
   7      SPEED
   8      IRISGround    
GND
1
2 3
4 6
7
Ground58
Example of auxillary 
control circuit
Note: Make sure that the lens and pan/tilt head stop 
at the center point of the zoom, focus, pan and tilt controls 
(or at the lever reset position if the controls have a lever reset function).
 Iris control Zoom 
controlPan 
control Tilt 
control Focus 
control
SPEED switch
100W
10KW
10KW
10KW
10KW6.8KW
20KW...

-14-
$77Video Output Connectors 
[VIDEO OUT 1, VIDEO OUT 2] (BNC Connector)
Video signals adjusted by the cable compensation cir-
cuit according to the cable length from the rotary head
to the control panel are output.  There are two output
connectors to be connected to a monitor, special
effect generator (SEG), VCR, or other video input
devices with coaxial cables.
$8Genlock Input Connectors 
[G/L IN] (BNC Connector)
Black burst signals are input to  one of the two connec-
tors in operating the camera...

-15-
nFront Panel
SPEED.SW
CHANGELOW  HIGH
ZOOM
REVERSENOR   REV
ZOOM/FOUCUS
EXCHANGEOFF    ON
FOUCUS
REVERSENOR   REV
TILT
REVERSENOR   REV
PA N
REVERSENOR   REV
%00Speed Switch Changing Switch 
[SPEED SW CHANGE, LOW/HIGH]
Changes the polarity of SPEED Switch @9.  If ZOOM
lever #6, FOCUS Lever #7, or PAN/TILT Lever #8is
moved while keeping SPEED Switch @9depressed, the
corresponding operation takes place at low speed,
provided that SPEED SW CHANGE Switch %0is in the
LOW position.  If one of these levers...

-16-
%2Zoom/Focus Exchange Switch 
(ZOOM/FOCUS EXCHANGE, ON/OFF]
ZOOM Lever #6and FOCUS Lever #7exchange their
function between them when this switch is set to the
ON position.  Unless this exchange is needed, keep
the switch in the OFF position.
With ZOOM/FOCUS EXCHANGE Switch %2in the ON
position, the operations shown on the panel do not
agree with the indications on the panel.  In this case,
paste the supplied seal on the panel.
%3Focus Reverse Switch 
[FOCUS REVERSE, NOR/REV]
Changes the operating...

-17-
pan/tilt head is properly set, the pan/tilt head will
pan or tilt in the opposite direction and the pan/tilt
head operation limiters will not be properly stored
in the memory.  For details on the setting of this
switch, refer to 
INSTALLATION OF PAN/TILT HEAD
at page 18 or the Operating Instructions for the
Pan/tilt Head. 

-18-
• Install the pan/tilt head after carefully reading the
Operating Instructions for Pan/tilt Head.
• Have four hex bolts (M6 x 4) ready for mounting the
pan/title head.  Select bolts of a length appropriate to
the material and structure of the mounting base and the
overall weight applied to it.  Fasten the bolts securely
with plain washers, spring washers, and hex nuts.  If
the bolts are not securely tightened, the pan/tilt head
might fall to cause injuries or accidents.  In case of sus-
pending the...