Panasonic Home Network Systrem Oudoor Camera Kx Hnc600w Installation Guide

							5Attach the safety wire to the wall.
R Place the ring of the safety wire ( A)
on the wall.
R Place the washer ( B) on top of the
ring of the safety wire.
R Tighten the screw ( C) for the safety
wire on top of the washer.
Note:
R Attach the safety wire while it is bent.
R Attach the safety wire high on the wall
so that the camera does not strike
anyone in the event the camera
detaches from the wall.
R Do not hang from the camera or stand.
6 Connect the DC cable to the AC adaptor.
R Pull the DC cable indoors, and connect
the DC cable plug ( A) to the AC
adaptor plug ( B).
R Connect the AC adaptor ( C) to the
power outlet.
 Outdoors Indoors
Note:
R Use only the supplied Panasonic AC
adaptor PNLV236.
R Be sure to connect the DC cable plug
and AC adaptor plug indoors.
Note about power connections
AC adaptor connection
R The AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel
warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become
disconnected.
Power failure
R The camera will not work during a power
failure.
For assistance, please visit www.panasonic.com/support21
Setup1
2
3 1 2 3
2 1
12  
						

							Testing the motion
detection range
After you have installed the  [Home Network]
app on your mobile device, you can use your
mobile device to test the performance of the
camera’s motion detection features.
For details about these operations, refer to the
User’s Guide (page 26).
1 Start the  [Home Network]  app and
display live images from the camera.
2 Move to an area within the camera’s
viewable area.
3 While moving near the camera, use your
mobile device to observe where you are
in the viewable area when the camera’s
motion detection features are triggered.
R When the motion detection features
are triggered, the camera’s LED
indicator lights in red for about 3
seconds.
4 Note the areas of the viewable area
where movement is detected, and make
adjustments as necessary.
Note:
R You can adjust the area detectable by the
visual sensor. For more information, refer to
the User’s Guide (page 26).
R You can adjust the area detectable by the
infrared sensor. See “Adjusting the infrared
sensor range”, page 22.
Testing the microphone
To test the microphone, speak loudly and
clearly into the microphone while a mobile
device user is viewing live images from the
camera.
Adjusting the infrared
sensor range
If there are objects that you do not want the
infrared sensor to detect, you can adjust the
detectable area by attaching sensor range
caps.
Sensor range cap types and
detectable area
In addition to the standard cap (already
attached to the camera), there are 4 cap types
(cap 1-4). Each cap blocks different areas of
the sensor range and can be attached at
45-degree increments. Refer to the following
and attach the proper cap at the proper angle.
R The detectable areas shown here are an
approximation for when the  [IR Sensor]
setting is set to  [Normal]. For more
information, refer to the User’s Guide
(page 26).
R The detectable area rotates according to
the sensor range cap angle.
22For assistance, please visit www.panasonic.com/support
Appendix 
						

							Situation and cap
typesApproximate detection range (view when looking from above)  *120 °C (68 °F)0 °C (32 °F)30 °C (86 °F)When you want
both sides of the
camera to be
detectable
Standard cap
(attached to the camera)
 5 m (16.4 feet) 6 m (19.7 feet) 4 m (13.1 feet)
When you want one
side to be
undetectable
Cap 1
Cap 2
Cap 3
(Example) Cap 1
 5 m (16.4 feet)
(Example) Cap 1
 6 m (19.7 feet)
(Example) Cap 1
 4 m (13.1 feet)
(Example) Cap 3
 5 m (16.4 feet)
(Example) Cap 3
 6 m (19.7 feet)
(Example) Cap 3
 4 m (13.1 feet)
When you want
both sides to be
undetectable
Cap 4(Example) Cap 4
 5 m (16.4 feet)
(Example) Cap 4
 6 m (19.7 feet)
(Example) Cap 4
 4 m (13.1 feet)
*1 Varies by ambient temperature at the camera installation location. Numeric values are
approximate. Detectable area is indicated by .
For assistance, please visit www.panasonic.com/support23
Appendix 1 1 2 2 3 3    1 1 2 2 3 3 1 1 2 2 3 3  1 1 2 2 3 3   
						

							About the attachment angle of the sensor range cap
Example 1
When there is an object on the right side of the viewable area that you do not want to be
detected (such as trees):
Attach one of caps 1-3 as shown in the example (
) according to the area you do not want to be
detected.
Example 2
When there is an object on the top left of the viewable area that you do not want to be
detected (cars in a street, etc.):
Attach one of caps 1-3 as shown in the example (
) according to the area you do not want to be
detected.
Example 1Example 224For assistance, please visit www.panasonic.com/support
Appendix1 2  1 2   
						

							Replacing sensor range caps
1 Remove the attached standard cap.
2Remove the desired sensor range cap from one of the 4 types ( A) and attach it to the
sensor ( B).
R When attaching, rotate the tab (
) on the cap toward the top or at a 45-degree angle
according to the type of cap or direction, and attach the cap on the camera, shown in the
following illustration.
For assistance, please visit www.panasonic.com/support25
Appendix 1 1
2
1  
						

							Features available when
using the [Home Network]
app
Some of the camera’s features that are
available when using the  [Home Network]
app are listed below. For more information,
refer to the User’s Guide (page 26).
– Security system
You can use the app to arm and disarm the
security system, confirm the current status
of the sensor, and view a log of previous
security events.
– Live camera monitoring
You can view live images from the camera,
even while away from home.
– Listen and talk
You can use your mobile device to talk and
listen to anyone within range of the
camera’s microphone and speaker.
– Sensor integration
You can configure the camera’s sensor
features to trigger other system events,
such as camera recording *1
, turning on an
electric device (such as a lamp), etc.
(Appropriate device required.)
*1 A commercially-available microSD card must be inserted into the hub in
order to record images.
– Notification
You can configure the camera to send a
notification to the  [Home Network] app
when the camera detect motion.Accessing  the  User’s  Guide
The User’s Guide is a collection of online
documentation that helps you get the most out
of the  [Home Network]  app.
1 iPhone ®
/iPad ®
Tap 
 in the app’s home screen.
Android™ devices
Tap 
 or press your mobile device’s
menu button in the app’s home screen.
2 Tap [User’s Guide] .
Note:
R You can also access the User’s Guide at
the web page listed below.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
26For assistance, please visit www.panasonic.com/support
Appendix    
						

							Specifications
R Standards
DECT 6.0 (Digital Enhanced Cordless
Telecommunications 6.0)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
120 V AC, 60 Hz
R Power consumption
Standby: 1.4 W
During operation:
1.5 W (when the LED lights are not lit)
2.3 W (when the LED lights are lit)
R Operating conditions
-20 °C – 50 °C (-4 °F – 122°F)
up to 90% relative humidity
(non-condensing)
R Transmitting range
Approx. 50 m (160 feet) indoors
Approx. 300 m (1,000 feet) outdoors
R Image sensor
0.3 megapixel CMOS
R Minimum illuminance required
0 lx *1
R Focal length
Fixed (0.4 m (1.3 feet) – infinity)
R Angular field of view (camera angle)
Horizontal: approx. 70°
Vertical: approx. 50°
R Motion detection method
Pyroelectric infrared sensor (PIR sensor)
and visual sensor
R PIR sensor detection range (when the
surrounding temperature is approx.
25 °C (77 °F))
Horizontal: approx. 70°
Vertical: approx. 20°
Detection range: approx. 5 m
R Visual sensor detection range
Horizontal: approx. 70°
Vertical: approx. 50°
R IP rating
IP55 *2
R Adjustable mounting angles
Horizontal: ±90°
Vertical: facing forward - facing down
approx. 60°
(adjustable when mounting)
R Dimensions
Approx. 75 mm  ´ 75 mm  ´ 173 mm (2
15/16 inches  ´ 2 15/16 inches  ´ 6 13/16
inches)
R Mass (weight)
Approx. 305  g (0.67 lb)
*1 The IR-LED will be lighted at the low illuminance conditions.
*2 Water resistance is only assured if the camera is installed correctly according to
the instructions in the Installation Guide,
and appropriate water protection
measures are taken. Do not install the
camera in areas directly exposed to water
or rain.For assistance, please visit www.panasonic.com/support27
Appendix 
						

							FCC and other information
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this phone.
CAUTION:
Any changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate this device.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/ TV technician for help.
Some cordless telephones operate at
frequencies that may cause interference to
nearby TVs and VCRs. To minimize or
prevent such interference, the base of the
cordless telephone should not be placed near
or on top of a TV or VCR. If interference is
experienced, move the cordless telephone
further away from the TV or VCR. This will
often reduce or eliminate interference.
FCC RF Exposure Warning:
R This product complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
R To comply with FCC RF exposure
requirements, the device must be installed
and operated 20 cm (8 inches) or more
between the product and all person’s body.
R This product may not be collocated or
operated in conjunction with any other
antenna or transmitter.
R For body-worn operation, the handset must
be used only with a non-metallic accessory.
Use of other accessories may not ensure
compliance with FCC RF exposure
requirements.
Notice:
R FCC ID can be found on the rear of the unit.28For assistance, please visit www.panasonic.com/support
Appendix 
						

							Customer services
For assistance, please visit www.panasonic.com/support29
AppendixCustomer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate your nearest 
Dealer or Service Center; purchase Parts and Accessories; or make Customer 
Service and Literature requests by visiting our Web Site at:
www.panasonic.com/support
or, contact us via the web at: 
www.panasonic.com/contactinfo
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
For hearing or speech impaired TTY users, TTY: 1-866-605-1277 Purchase Parts, Accessories and Owner’s Manual online for all 
Panasonic Products by visiting our Web Site at:
www.pstc.panasonic.com
or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-237-9080 (Fax Only) 
(Monday - Friday 9 am to 9 pm, EST.)
Panasonic National Parts Center
20421 84th Avenue S., Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express.)
Accessory Purchases (United States and Puerto Rico)
You may also contact us directly at: 1-800-211-PANA (1-800-211-7262),
Monday - Friday 9 am to 9 pm; Saturday - Sunday 10 am to 7 pm, EST.  
						

							Warranty (For United States and Puerto Rico)
30For assistance, please visit www.panasonic.com/support
AppendixLimited Warranty Coverage
Labor
One (1) Year Parts
One (1) Year
Online Repair Request
To submit a new repair request and for quick repair status visit our Web Site at
www.panasonic.com/repair
PROOF OF PURCHASE.
Panasonic Home Network System Products
Limited Warranty
Mail-In Service--Online
If your product does not work properly because of a defect in materials or workmanship, 
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length 
of the period indicated on the chart below, which starts with the date of original purchase 
(“Limited Warranty period”), at its option either (a) repair your product with new or 
refurbished parts, or  (b) replace it with a new or a refurbished equivalent value product, or 
(c) refund your purchase price. The decision to repair, replace or refund will be made by 
the warrantor.
During the “Labor” Limited Warranty period there will be no charge for labor. During the 
“Parts” Limited Warranty period, there will be no charge for parts. You must mail-in your 
product prepaid during the Limited Warranty period. This Limited Warranty excludes both 
parts and labor for batteries, antennas, and cosmetic parts (cabinet). This Limited 
Warranty only applies to products purchased and serviced in the United States or Puerto 
Rico. This Limited Warranty is extended only to the original purchaser and only covers 
products purchased as new. Home Network System Products
microSD card (Included model only)       90 days              N/A
When shipping the unit carefully pack in a padded shipping carton, include all 
accessories, and send it prepaid. Include a letter detailing the complaint, a return 
address and provide a day time phone number where you can be reached. P.O. Boxes 
are not acceptable. Keep the tracking number for your records. A copy of valid 
registered receipt is required under the 1 year parts and labor Limited Warranty.
For Limited Warranty service for headsets if a headset is included with this 
product please follow instructions above.
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE 
PURCHASER WILL BE REQUIRED TO FURNISH A SALES 
RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, 
AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE 
CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH