Panasonic Home Network System Kx Hn Users Guide

Motion sensor LED indicator
The LED indicator on the motion sensor does not light during normal operation. You can press 
 and
check the LED indicator to confirm the sensor’s status.
OffNo battery powerGreenNo motion detectedRegistration mode (you pressed and held )RedMotion detectedSensor is out of range of the hub, or is not registered to a hub
Note:
R After pressing 
 and confirming the sensor’s status, press  again to turn off the LED
indicator and conserve battery power.
Window/door sensor LED...

Note:
R After pressing 
 and confirming the sensor’s status, press  again to turn off the LED
indicator and conserve battery power.
Glass break sensor LED indicator
The LED indicator on the glass break sensor does not light during normal operation. You can press
 and check the LED indicator to confirm the sensor’s status.
OffNo battery powerGreenNo glass break detectedRegistration mode (you pressed and held )RedGlass break detectedSensor is out of range of the hub, or is not registered to a hub
Note:
R...

Keychain remote LED indicatorOffNormal operation, or no battery power*1Green[Disarm]
 mode selected (you pressed the disarm button), or you pressed
the smart button *2Registration mode (you pressed and held )Green and redLow batteryOrangeSignal is being sent to the hub (you are pressing a button)Red[Arm: Away]
 mode selected (you pressed the arm button) *2Keychain remote is out of range of the hub, or is not registered to a hub
*1 The LED lights for about 2 seconds after a button is pressed, then turns...

Alarm system features (overview)
You can use the system as an alarm system. When the alarm system is triggered, such as when motion
is detected or when a window or door is opened, the system can:
– send a notification to your mobile devices ( “Status notifications”, Page 37)
– call a pre-programmed phone number (such as your mobile phone or work phone) and play a message to alert you to the situation ( “Alert by phone call”, Page 47)
– execute a smart control scenario, such as recording camera images or...

3The sensor makes a detection (a door sensor detects that its door was opened, a motion sensor
detects motion, etc.).
R If the sensor is configured to use entry time, entry time is in effect beginning when the sensor was
triggered. During this time, the system responds as follows.
– The hub sounds an alert (i.e., entry delay alert).
– The system sends a notification to your mobile devices (i.e., entry delay start notification). This feature can be disabled ( “Notification settings”, Page 96).
– The event...

–Glass break sensors:  Enabled
– Indoor camera motion detection features:  Disabled
– Outdoor camera motion detection features:  Enabled
Disarm
Use this mode when alarm system features are not needed.
Water leak sensors are always enabled, even when this mode is selected. All other sensors are disabled
when this mode is selected.
Confirming the current arm mode
The icons displayed near the top of the home screen indicate the current arm mode.
See  “Arm mode icons”, Page 33 for details.
Changing the...

Setting the exit delay alert volume
The hub sounds an alert while the exit delay is counting down. To adjust the volume, tap 
, select the
desired volume, and then tap  [OK]. While adjusting this setting, the alert will sound from the hub so that
you can confirm what the alert sounds like and its volume.
Note:
R This setting is only available when  [Arm Settings (Away)] is selected in step 3, page 46.
Entry delay time and alert volume (available for [Arm: Away] mode and [Arm: At Home] mode)
The entry...

Note:
R In order to use this feature, the hub must be connected to your landline. For information about phone
line connection, refer to the System Setup Guide included with your hub.
Configuring the alert by phone call feature
1 From the  [Home Network]  app home screen, tap  [Settings].
2 Tap  [Arm Settings] .
3 Tap  [Alert by Phone Call] .
4 Turn on the  [Alert by Phone Call]  switch.
5 Tap  [Arm Condition] .
6 Select the desired setting and then tap  [OK].
– [Away/At Home] : Alert by phone call is...

Alarm system PIN
The alarm system PIN is required when using certain devices to change the arm mode or cancel an alert.
You can use the app to change the PIN.
1 From the  [Home Network]  app home screen, tap  [Settings].
2 Tap  [Arm Settings] .
3 Tap  [Change Arm PIN] .
4 Enter the current PIN and then tap  [OK].
R The default PIN is “0000”.
5 Enter the desired PIN and then tap  [OK].
6 Enter the desired PIN again and then tap  [OK].
Note:
R The alarm system PIN is required when using the following...

I want the lights to turn on automatically when I come home.
1 Which device:  Foyer smart plug
2 When:  When the alarm system is armed and the app detects that your mobile device has
reconnected to your wireless router (because you came home)
3 What:  Turn the smart plug on
I want to turn on my bedside lamp if my baby starts crying.
1 Which device:  Master bedroom smart plug
2 When:  The child’s room camera’s sound sensor is triggered between 10:00 PM and 6:00 AM
3 What:  Turn the smart plug on for 2...