Panasonic Home Network System Digital Cordless Handset Kx Hnh100 Operating Instructions

Answering system
T
he answering system can answer and record
calls for you when you are unavailable to
answer the phone.
You can also set the unit to play a greeting
message but not to record caller messages by
selecting  “Greeting only ” as the recording
time setting (page 36).
Important:
R Make sure the unit’s date and time setting
is correct. The time setting of the system is
configured with the date and time of the
mobile device registerd to the hub. For
more information, refer to the System Setup...

unit plays a pre-recorded greeting asking
c
allers to leave a message.
– If the message recording time (page 36) is set to  “Greeting only ”, callers’
messages are not recorded and the unit
plays a different pre-recorded greeting
message asking callers to call again. Resetting to a pre-recorded greeting
m

essage
If you want to use a pre-recorded greeting
message once you record your own greeting
message, your own recorded greeting
message is erased.
1 MMENU N#304
2 MYES N a  M OFF N Playing back the...

R
During fast-forwarding, the handset makes
a continuous beeping sound.
Fast-forwarding speed may vary depending
on the recorded message.
R Even if you press and hold  ME N when the
end of this message is played, the next
message is played at normal speed. Calling back (Caller ID subscribers
o

nly)
1 Press  MPAUSE N during playback.
2 Mb N:  “Call back ” a  M SELECT N
n Editing the number before calling back
1 Press  MPAUSE N during playback.
2 Mb N:  “Edit & Call ” a  M SELECT N
3 Press  MEDIT N...

2
Mb N:  “ N otification to ” a  M SELECT N
3 MMENU N a  M b N:  “Edit ” a  M SELECT N
4 Edit the name if necessary (16 characters
max.).  a M OK N
5 Edit the phone number if necessary (24
digits max.).  a M OK N a  M SELECT N a
M OFF N Erasing the set phone number
1
MM

ENUN#338
2 Mb N:  “ Notification to ” a  M SELECT N
3 MMENU N a  M b N:  “Erase ” a  M SELECT N
4 Mb N:  “Yes ” a  M SELECT N a  M OFF N
R The new message alert setting is
turned off. Activating/inactivating the remote
a

ccess code to...

Using the answering system
r emotely
1 Dial your phone number from a
touch-tone phone.
2 After the greeting message starts, enter
your remote access code.
3 Follow the voice guidance prompts as
necessary or control the unit using
remote commands (page 35).
4 When finished, hang up. Voice guidance
n
W

hen the English voice guidance is
selected
During remote operation, the unit’s voice
guidance starts and prompts you to press
1  to perform a specific operation, or press
2  to listen to more available...

Number of rings before the unit
a nswers a call
You can change the number of times the
phone rings  “Ring count ” before the unit
answers calls. You can select 2 to 7 rings, or
“ Toll saver ”.
The default setting is  “4 rings ”.
“ Toll saver ”: The unit’s answering system
answers at the end of the 2nd ring when new
messages have been recorded, or at the end
of the 5th ring when there are no new
messages. If you call your phone from outside
to listen to new messages (page 35), you
know that there are no...

Home Network System
i ntegration
If you have other devices registered to the
hub, such as cameras, sensors, and smart
plugs, you can use the handset as an
integrated part of the Home Network System.
Specifically, you can use the handset to:
– arm and disarm the system’s security features (page 37).
– receive notifications when the sensors are triggered.
– display the status of each sensor (page 38).
– turn smart plugs on and off (page 39). Security features
Y
 ou can use the handset to arm and disarm
the...

2
Enter the password.  a M OK N
Note:
R By pressing  MDISARM N, you can disarm the
security system and stop the alert. See
“Arming and disarming the system”,
page 37. Displaying sensor status
T
 he status of each sensor device is shown on
the handset.
1 MMENU N#801
2 Mb N: Select  “All locations ” or the
area in which the desired sensor devices
belong to.  a M SELECT N
3 Mb N: Select the desired sensor.
R Press  MREFRESH N to refresh the
displayed information. Talking notification feature
T
 his feature...

5
MOFF NSmart plug features
S

mart plugs (KX-HNA101) allow you to use
the handset to turn electric devices on and off.
Smart plugs also feature an overcurrent
sensor that automatically shuts off the electric
device if an overcurrent is detected. Turning smart plug on and off
T
 here are 3 ways to turn smart plugs on and
off.
– All smart plugs can be turned on or off at once.
– All smart plugs in a selected area can be turned on or off at once.
– Individual smart plugs can be turned on or off.
Turning...

Accessing t
he User’s Guide
The User’s Guide is a collection of online
documentation that helps you get the most out
of the Home Network app.
1 iPhone ®
/iPad ®
Tap   in the app’s home screen.
A

ndroid™ devices
Tap   or press your mobile device’s
m

enu button in the app’s home screen.
2 Tap [User’s Guide] .
Note:
R You can also access the User’s Guide at
the web page listed below. www.panasonic.net/pcc/support/tel/
h

omenetwork/manual/
40 For assistance, please visit www.panasonic.com/supportHome...