Panasonic High Definition Plasma Display Th 103vx200 Operating Instructions

21
Basic Controls
Remote Control Transmitter
Standby (ON / OFF) button
The Plasma Display must fi rst be plugged 
into the wall outlet and turned on at the power 
switch (see page 17).
Press this button to turn the Plasma Display 
On, from Standby mode. Press it again to turn 
the Plasma Display Off to Standby mode.
AUTO SETUP button
Automatically adjusts the position/ size of 
the screen. (see page 29)
COMPO. button
Press to select Component or RGB 
input. (see page 19)
PC button 
Press to select PC...

ENTER/ 
Right side surface
22
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its ma\
ximum size, including wide screen cinema format 
picture.Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 64). 
The aspect mode changes each time the ENTER button is pressed.
[For 3D images]
The aspect is fi xed as “FULL” and you cannot switch.
[from the unit] Note: 
Be aware that if you put the display in a...

23
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes corresponding\
 to the 3D effect by wearing the 
3D Eyewear (supplied).
This display supports “Frame Sequential*
1”, “Side by Side*2” and “Top and Bottom*3” 3D formats.
*1:  The 3D format that the images for the left and right eyes are recorded w\
ith the high de fi nition quality and alternately played back*
2,  *
3: Other available 3D formats
3D Eyewear set
3D Eyewear Specialised band
Nose pad A Nose pad B 3D Eyewear case...

24
Replacing the battery■
     When the battery is running low, the indicator lamp  fl ashes 5 times on turning the 3D Eyewear on. In this case, early 
battery replacement is recommended.
    • 
 Dispose of the old batteries as non-burnable rubbish, or in line with th\
e waste disposal regulations in your local area.
   Loosen the screw and remove the battery cover using the supplied screwdr\
iver
Screwdriver (supplied)
Battery cover
   Replace the battery
•  Use the speci fi ed type of battery...

25
To view the 3D images
Viewing 3D images
To view the contents of the Frame Sequential format (ex. 3D-compatible B\
lu-ray Disc, etc.) with 3D effect
Connect the 3D-compatible player via an HDMI cable (see page 14) and p\
layback the contents.
•  Use fully wired HDMI compliant cable.
•   For the settings of the player, read the manual of the player.
•   If you use the non 3D-compatible player, the images will be displayed without 3D effect.
To view the contents of 3D formats other than Frame Sequential...

26
Troubleshooting for 3D Eyewear 
Table of images that can be seen for each 3D Picture 
Format and the source image format
Symptoms Checks
Cannot see 3D images •  Has the 3D Eyewear been switched On?
•   Ensure that “3D EYEWEAR” in “3D SETTINGS” is set to “ON”\
. (see 
page 47)
•   Some 3D image signals may not be automatically recognized as 3D 
images. Set “3D INPUT FORMAT” in “3D SETTINGS” to match the 
picture format. (see page 47)
•   Check that there are no obstacles between the infrared sensors...

27
On-Screen Menu Displays
Remote Control Unit
1Display the menu screen. Press
MENU  Press several times.
Each time the MENU button is pressed, the 
menu screen will switch. Normal Viewing PICTURE
SOUND POS. /SIZE
SET UP
2Select the menu.
SET UP
POS. /SIZE
SOUND
OPTIONS
PICTURE
MONITOR
MEMORY SAVE
MEMORY LOAD MEMORY EDIT
PICTURE MENU
PICTURE
NORMALIZE
0
BRIGHTNESS
ADVANCED SETTINGS 0
WARM
SHARPNESS
COLOR TEMP
2  Access
1  Select
3Select the item.
Select
ENTER/  Press.
 Select.
PICTURE MENU
250
PICTURE...

28
Adjusting POS. /SIZE
1Display the menu screen.
2Select “POS. /SIZE”.
SET UP
POS. /SIZE
SOUND PICTURE
2  access
1  select
3Select the item and set.
2   adjust
1   select
1:1 PIXEL MODE H-POS
0 0 0
H-SIZE
AUTO SETUP
NORMALIZE
V-POS 0
V-SIZE
0
DOT CLOCK
0
0
CLOCK PHASE
CLAMP POSITIONOFF
UNDER SCAN OFF
4Exit the menu.
Notes:
•  Adjustment details are memorized separately for different input signal formats. (Adjustments for component signals are  memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p,...

29
Adjusting POS. /SIZE
● AUTO SETUPH-POS/V-POS, H-SIZE/V-SIZE, DOT CLOCK and CLOCK PHASE are automatically adjusted when 
the RGB or PC signal is received.
This setting is enabled under the following conditions:
•  When “COMPONENT/RGB-IN SELECT” or “YUV/RGB-IN SELECT” in the\
 “SET UP” menu (see 
page 44) is set to “RGB”, this setting is enabled.
•  When the signal is not PC format, this setting is enabled only if “OV\
ER SCAN” (see page 30)  is “OFF” or “1:1 PIXEL MODE” (see page 30) is “ON”, and...

30
Adjusting POS. /SIZE
● 1:1 PIXEL MODEAdjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
•  Select ON when you would like to replay 1920 × 1080 input signal.
•  Applicable input signal;
  1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50\
p · 60p, 1250 (1080) / 50i
•  Select OFF when  fl ickering is shown around the image.
•  H-SIZE and V-SIZE cannot be adjusted when ON is selected.
 OFF ON
●  CLAMP POSITION(During Component and RGB input signal)
Adjusts the clamp position...