Panasonic Hdc Sdt750 Operating Instructions

21VQT3B18
∫Charging/Recording time
≥Temperature: 25 oC (77 oF)/humidity: 60%RH 
* The battery pack holder kit VW-VH04 (optional) is necessary.
≥ These times are approximations.
≥ The indicated charging time is for when the battery has been discharged completely. 
Charging time and recordable time vary depending on the usage conditions such as 
high/low temperature.
≥ Recordable time of 3D recording mode is the same.
(During 3D recording mode, 1080/60p recording mode cannot be used.)
≥The actual...

22VQT3B18
Important:
While the DC cable is connected to the AC adaptor, the battery will not charge.
≥Do not use the AC cable with any other equipment as it is designed only for this unit. 
Also, do not use the AC cable from other equipment with this unit.
1Connect the AC cable to the AC adaptor and the AC outlet.
2Connect the DC cable to the AC adaptor.
3Connect the DC cable to the DC input terminal [DC IN].
≥When removing the AC adaptor, be sure to hold down the power button until the status 
indicator...

23VQT3B18
Preparation
Setup
2
Recording to a card
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for 
motion picture recording.
* The SD Speed Class Rating is the speed standard for successive writes.
≥4 GB or more Memory Cards that do not 
have the SDHC logo or 48 GB or more 
Memory Cards that do not have the SDXC 
logo are not based on SD Memory Card 
Specifications. ≥When the write-protect 
switch A on SD card is 
locked, no recording, 
deletion or editing will 
be possible...

24VQT3B18
Caution:
Check that the access lamp has gone off.
1Open the LCD monitor.
2Open the SD card/terminal 
cover and insert (remove) the 
SD card into (from) the card 
slot.
≥Face the label side  B in the direction 
shown in the illustration and press it 
straight in as far as it will go.
≥ Press the center of the SD card and then 
pull it straight out.
3Securely close the SD card/
terminal cover.
≥Securely close it until it clicks.
≥Do not touch the terminals on the back of 
the SD card.
≥ Do not...

25VQT3B18
Preparation
Setup
3
Turning the unit on/off
You can turn the unit on and off using the power button, the LCD monitor or the viewfinder.
Press the power button to turn on the unit.
AThe status indicator lights on.
Opening the LCD monitor or extending the viewfinder turns on the unit. Closing the LCD 
monitor/viewfinder turns off the unit.
During general use, you may find it convenient to turn the unit on/off using the LCD 
monitor or viewfinder.
∫ To turn on the unit
A The status indicator...

26VQT3B18
Preparation
Setup
4
Selecting a mode
Change the mode to recording or playback.
Operate the mode dial to change the mode to  ,   or  .
Motion Picture Recording Mode (l31)
Still Picture Recording Mode ( l33)
Playback Mode ( l37, 90)
≥Align with the status indicator  A.
HDC-SDT750&TMT750-P-VQT3B18_mst.book  26 ページ  ２０１０年８月２０日　金曜日　午後３時５３分 

27VQT3B18
Preparation
Setup
5
Adjusting LCD monitor/
viewfinder
You can operate by directly touching the 
LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) 
for detailed operation or if it is hard to 
operate with your fingers.
∫Touch
Touch and release the touch screen to select 
icon or picture.
≥Touch the center of the icon.
≥ Touching the touch screen will not operate 
while you are touching another part of the 
touch screen.
∫ Drag
Move your finger while...

28VQT3B18
∫Adjusting the field of view
It adjusts the field of view to show the 
images on the viewfinder clearly.
Adjust the focus by rotating the 
eyepiece corrector dial.
≥Extend the viewfinder and close the LCD 
monitor to turn on the viewfinder.
¬ Change the mode to   or  .
Extend the viewfinder and rotate the 
LCD monitor towards the lens side.
≥LCD monitor and viewfinder are turned on 
during the face-to-face recording when the 
viewfinder is extended.
≥
The image is horizontally flipped as if you...

29VQT3B18
Preparation
Setup
6
Setting date and time
When the unit is turned on for the first time, a message asking you to set the date and time 
will appear.
Select [YES] and perform steps 2 to 3 below to set the date and time.
¬Change the mode to   or  .
1Select the menu.
2Touch the date or time to be 
set, then set the desired value 
using / .
A Displaying the World time setting 
(l 42):
[HOME]/ [DESTINATION]
≥ The year can be set between 2000 and 
2039.
≥ The 12-hour system is used to display the...

30VQT3B18
Basic
Recording/
Playback
1
Before recording
∫Basic camera positioning
1 Hold the unit with both hands.
2 Put your hand through the grip belt.
3 It is convenient to use the Sub-recording Start/Stop button  A when holding the unit at 
waist level.
≥ When recording, make sure your footing is stable and there is no danger of colliding with 
another person or object.
≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is 
backlit, it will become dark in the...