Panasonic Hdc Sd40 Owners Maual Manual

							21VQT3J95
Charging the battery
Important:
≥Use the supplied AC adaptor. Do not use the AC adaptor of another device.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit. 
Also, do not use the AC cable from other equipment with this unit.
≥ The battery can also be charged using a battery charger (VW-BC10PP; optional).
≥ The battery will not be charged if the unit is turned on.
≥ It is recommended to charge the battery in a temperature between 10  oC to 30  oC 
(50  oF to 86  oF). (The battery temperature should also be the same.)
A DC input terminal
≥ Insert the plugs as far as they will go.
1Connect the AC adaptor to the DC input terminal.
2Connect the AC cable to the AC adaptor, then the AC outlet.≥The status indicator will flash red at an interv al of 2 seconds, indicating that charging has 
begun.
It will turn off when the charging is completed.
∫ Connecting to the AC outlet
If you turn on the unit while connecting with the AC adaptor, you can use the unit with power 
supplied from the outlet.
≥If the status indicator flashes at a particularly fast or slow rate, refer to page 111.
≥ We recommend using Panasonic batteries ( l12, 22, 120).
≥ If you use other batteries, we cannot guarantee the quality of this product.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period 
of time with doors and windows closed.
When this unit is purchased, the battery is not charged. Charge the battery fully 
before using this unit for the first time.

HDC-SD40&TM40P_PC_VQT3J95_mst.book  21 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							22VQT3J95
Charging and recording time
∫Charging/Recording time
≥Temperature: 25 oC (77 oF)/humidity: 60%RH (When using AC adaptor) 
≥ These times are approximations.
≥ The indicated charging time is for when the battery has been discharged completely. 
Charging time and recordable time vary depending on the usage conditions such as 
high/low temperature.
≥The actual recordable time refers to the recordable time when repeatedly starting/stopping 
recording, turning the unit on/off, moving the zoom lever etc.
≥ The batteries heat up after use or charging. This is not a malfunction.
HDC-SD40
Battery model number
[Voltage/Capacity  (minimum)]Charging timeRecording modeMaximum 
continuous 
recordable timeActual 
recordable  time
Supplied battery/
VW-VBK180 (optional) [3.6 V/1790 mAh] 2h25min[HA], [HG], 
[HX] 2h15min 1h10min
[iFrame] 2h 40min 1h25min
VW-VBK360 (optional) [3.6 V/3580 mAh] 4h20min[HA], [HG] 4h30min 2h20min
[HX] 4h35min 2h20min
[iFrame] 5h20min 2h45min
HDC-TM40/HDC-TM41
Battery model number [Voltage/Capacity  (minimum)]Charging timeRecording modeMaximum 
continuous 
recordable timeActual 
recordable  time
Supplied battery/
VW-VBK180 (optional) [3.6 V/1790 mAh] 2h25min[HA], [HG], 
[HX] 2h15min 1h10min
[iFrame] 2h 40min 1h25min
VW-VBK360 (optional) [3.6 V/3580 mAh] 4h20min[HA], [HG] 4h30min 2h20min
[HX] 4h35min 2h20min
[iFrame] 5h20min 2h45min
HDC-SD40&TM40P_PC_VQT3J95_mst.book  22 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							23VQT3J95
Battery capacity indication≥The display changes as the battery capacity reduces. 
####
If there is less than 3 minutes remaining, then   will become red. If the battery 
discharges, then   will flash.
≥ The remaining battery capacity is displayed when using the Panasonic battery that you 
can use for this unit. The actual time can vary depending on your actual use.
≥ When using the AC adaptor or batteries made by other companies, the remaining 
battery capacity will not be shown.
HDC-SD40&TM40P_PC_VQT3J95_mst.book  23 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							24VQT3J95
The unit can record still pictures or motion pictures to an SD card or built-in memory. To 
record to an SD card, read the following.
Cards that you can use with this unit
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for 
motion picture recording.
* SD Speed Class Rating is the speed standard regarding continuous writing. 
Check via the label on the card, etc.
≥Please confirm the latest information abo ut SD Memory Cards/SDHC Memory Cards/
SDXC Memory Cards that can be used for motion picture recording on the following 
website.
http://panasonic.jp/support/global/cs/e_cam
(This website is in English only.)
≥ 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory 
Cards that do not have the SDXC logo are not based on SD Memory Card Specifications.
≥ Memory cards that exceed 64 GB cannot be used.
≥ When the write-protect switch  A on SD card is locked, no recording, 
deletion or editing will be possible on the card.
≥ Keep the Memory Card out of reach of children to prevent swallowing.
Preparation
Recording to a card
This unit (an SDXC compatible device) is  compatible with SD Memory Cards, SDHC 
Memory Cards and SDXC Memory Cards.  When using an SDHC memory card/SDXC 
memory card with other equipment, check the equipment is compatible with these 
memory cards.
Card typeCapacityMotion picture recordingStill picture  recording
SD 
Memory Card 8 MB/16 MB/32 MB Cannot be used.
Cannot be 
guaranteed in 
operation.
64 MB/128 MB/
256 MB Cannot be guaranteed in 
operation.
512MB/1GB/2GB
Can be used. Can be used.
SDHC 
Memory Card 4GB/6GB/8GB/
12 GB/16 GB/24 GB/32 GB
SDXC 
Memory Card 48 GB/64 GB
e.g.:
32
HDC-SD40&TM40P_PC_VQT3J95_mst.book  24 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							25VQT3J95
Inserting/removing an SD card
Caution:
Check that the access lamp has gone off.
1Open the LCD monitor.
2Open the SD card cover and 
insert (remove) the SD card 
into (from) the card slot B.
≥Face the label side  C in the direction 
shown in the illustration and press it 
straight in as far as it will go.
≥ Press the center of the SD card and then 
pull it straight out.
3Securely close the SD card 
cover.
≥Securely close it until it clicks.
≥Do not touch the terminals on the back of 
the SD card.
≥ Do not apply strong shocks, bend, or drop 
the SD card.
≥ Electrical noise, static electricity or the 
failure of this unit or the SD card may 
damage or erase the data stored on the 
SD card.
≥ When the card access lamp is lit, do not:
jRemove the SD card
j Turn the unit off
j Insert and remove the USB cable
j Expose the unit to vibrations or shock
Performing the above while the lamp is on 
may result in damage to data/SD card or 
this unit. ≥
Do not expose the terminals of the SD 
card to water, dirt or dust.
≥ Do not place SD cards in the following 
areas:
jIn direct sunlight
j In very dusty or humid areas
j Near a heater
j Locations susceptible to significant 
difference in temperature (condensation 
can occur.)
j Where static electricity or 
electromagnetic waves occur
≥ To protect SD cards, return them to their 
cases when you are not using them.
≥ About disposing of or giving away the SD 
card. ( l111 )
When using an SD card not from Panasonic, 
or one previously used on other equipment, 
for the first time on this unit, format the SD card. ( l44) When the SD card is formatted, all 
of the recorded data is deleted. Once the data is deleted, it cannot be restored.


Access lamp [ACCESS]  A
≥When this unit is accessing the SD 
card or built-in memory, the access 
lamp lights up.
HDC-SD40&TM40P_PC_VQT3J95_mst.book  25 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							26VQT3J95
You can turn the unit on and off using the power button or by opening and closing the LCD 
monitor.
Turning the unit on and off with the power button
Press the power button to turn on the unit.
AThe status indicator lights on.
Turning the unit on and off with the LCD monitor
Unit is turned on when the LCD monitor is opened, and unit is turned off when it is closed.
During normal use, opening and closing of the LCD monitor can be conveniently used 
to turn the unit on/off.
∫To turn on the unit
A The status indicator lights on.
∫To turn off the unit
B The status indicator goes off.
≥ The unit will not turn off while recording motion  pictures even if the LCD monitor is closed.
≥ In the following cases, opening the LCD monitor does not turn on the unit. Press the power 
button to turn on the unit.
jWhen the unit is  originally purchased
j When you have turned off the unit using the power button
Preparation
Turning the unit on/off
A clicking sound is heard when the unit is shaken.
≥This is the sound of the lens moving and is not a defect.
This sound will no longer be heard when the unit is turned on and change the mode to 
.
To turn off the unitHold down the power button until the 
status indicator goes off.

HDC-SD40&TM40P_PC_VQT3J95_mst.book  26 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							27VQT3J95
Change the mode to recording or playback.
Operate the mode switch to change the mode to   or  .
Preparation
Selecting a mode
Recording Mode (l31)
Playback Mode ( l36, 63)
HDC-SD40&TM40P_PC_VQT3J95_mst.book  27 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							28VQT3J95
When the unit is turned on for the first time, a message asking you to set the date and time 
will appear.
Select [YES] and perform steps 2 to 3 below to set the date and time.
¬Change the mode to  .
1Select the menu. ( l39)
2Select the date or time using  2/1 and set the desired value using 
3/ 4.
A Displaying the World time setting 
(l 40):
[HOME]/ [DESTINATION]
≥ The year can be set between 2000 and 
2039.
≥ The 12-hour system is used to display the 
time.
3Press the ENTER button.≥A message prompting for World time setting may be displayed. Perform the World time 
setting by pressing the ENTER button. ( l40)
≥ Press the MENU button to complete the setting.
≥The date and time function is driven by a built-in lithium battery.
≥ When this unit is purchased, the clock is set. If the time display becomes [- -], the built-in 
lithium battery needs to be charged. To recharge the built-in lithium battery, connect the AC 
adaptor or attach the battery to this unit. Leave the unit as it is for approx. 24 hours and the 
battery will maintain the date and time for approx. 4 months. (The battery is still being 
recharged even if the unit is off.)
Preparation
Setting date and time
: [SETUP] #  [CLOCK SET]
HDC-SD40&TM40P_PC_VQT3J95_mst.book  28 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							29VQT3J95
∫Basic camera positioning
1 Hold the unit with both hands.
2 Put your hand through the grip belt.
≥ When recording, make sure your footing is stable and there is no danger of colliding with 
another person or object.
≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is 
backlit, it will become dark in the recording.
≥ Keep your arms near your body and separate your legs for better balance.
≥ Do not cover the microphones with your hand etc.
∫ Basic motion picture recording
≥The unit should normally be held steady when recording.
≥ If you move the unit when recording, do so slowly, maintaining a constant speed.
≥ The zoom operation is useful for recording subjects you cannot get close to, but overuse of 
zoom in and zoom out can make the resulting motion picture less enjoyable to watch.
∫ Recording yourself
Rotate the LCD monitor towards the lens side.
≥ The image is horizontally flipped as if you see a mirror 
image. (However the image recorded is the same as a 
normal recording.)
≥ Only some indications will appear on the screen. When 
 appears, return the direction of the LCD monitor to 
normal position and check the warning/alarm indication. 
( l 101)
Basic
Before recording
HDC-SD40&TM40P_PC_VQT3J95_mst.book  29 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分 
						

							30VQT3J95
The card and built-in memory can be selected separately to record motion pictures or still 
pictures.
1Change the mode to .
2Select the menu. ( l39)
3Select the media for recording the motion pictures and the media for 
recording the still pictures using  3/4/ 2/1, and press the ENTER 
button.
≥ The media is selected separately to motion pictures or still pictures is highlighted in yellow.
≥ Select   and press the ENTER button to return to the previous screen.
4Press the MENU button to complete the settings.
Basic
Selecting a media to record 
[HDC-TM40/HDC-TM41]
: [MEDIA SELECT]
A[VIDEO/SD CARD]
B [VIDEO/Built-inMemory]
C [PICTURE/SD CARD]
D [PICTURE/Built-inMemory]

 
HDC-SD40&TM40P_PC_VQT3J95_mst.book  30 ページ  ２０１１年１月２０日　木曜日　午前１１時４９分