Panasonic Hdc Sd10 Operating Instructions

							21VQT2H52
∫Charging/Recording time
≥ Temperature: 25 oC (77oF)/humidity: 60%
* The battery pack holder kit VW-VH04 (optional) is necessary.
≥ These times are approximations.
≥ The indicated charging time is for when the battery has been discharged completely. Charging 
time and recordable time vary depending on the usage conditions such as high/low 
temperature.
≥The actual recordable time refers to the recordable time when repeatedly starting/stopping recording, 
turning the unit on/off, moving the zoom lever etc.
≥ The batteries heat up after use or c harging. This is not a malfunction.
Charging and recording time
HDC-SD10
Battery model number
[Voltage/Capacity 
(minimum)]Charging timeMaximum continuously  recordable timeActual recordable  time
Supplied battery/
VW-VBG070 (optional) [7.2 V/725 mAh] 1h35min
1h20min 50min
VW-VBG130 (optional)
[7.2 V/1250 mAh] 2h35min
2h15min 1h25min
VW-VBG260 (optional)*
[7.2 V/2500 mAh] 4h40min
4h25min 2h45min
VW-VBG6 (optional)*
[7.2 V/5400 mAh] 9h25min
10h55min 6h45min
HDC-TM10/HDC-TM15
Battery model number
[Voltage/Capacity  (minimum)]Charging timeMaximum continuously 
recordable timeActual recordable  time
Supplied battery/
VW-VBG070 (optional) [7.2 V/725 mAh] 1h35min
1h20min 50min
VW-VBG130 (optional)
[7.2 V/1250 mAh] 2h35min
2h15min 1h25min
VW-VBG260 (optional)*
[7.2 V/2500 mAh] 4h40min
4h20min 2h40min
VW-VBG6 (optional)*
[7.2 V/5400 mAh] 9h25min
10h45min 6h40min
HDCSD10_TM10_TM15P-VQT2H52_eng.book  21 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							22VQT2H52
Battery capacity indication
≥The display changes as the battery capacity reduces.  ####
If there is less than 3 minutes remaining, then   will become red. If the battery discharges, 
then ( ) will flash.
≥ The remaining battery capacity is displayed when  using the Panasonic battery that you can use for 
this unit. It may take time to display the remaining battery capacity. The actual time can vary 
depending on your actual use.
≥ The maximum amount of remaining battery capacity able to be indicated is 9 hours 59 minutes. If 
the actual remaining time exceeds 9 hours 59 mi nutes, the indication will stay green and will not 
change until the remaining time falls below 9 hours 59 minutes.
≥ When changing modes, the time indication will turn off momentarily in order to recalculate the 
remaining battery capacity time.
≥ When using the AC adaptor or batteries made by ot her companies, the remaining battery capacity 
will not be shown.
HDCSD10_TM10_TM15P-VQT2H52_eng.book  22 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							23VQT2H52
Important:
While the DC cable is connected to the AC adaptor, the battery will not charge.
≥Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do 
not use the AC cable from other equipment with this unit.
A DC output terminal
1Connect the AC cable to the AC adaptor and the AC outlet.
2Connect the DC cable to the AC adaptor.
3Insert the DC cable.
≥Always use the supplied AC adaptor or a  genuine Panasonic AC adaptor (VW-AD21PP; optional).
≥ When removing the AC adaptor, be sure to hold down the power button until the status indicator goes 
off. Then remove the AC adaptor.
Connecting to the AC outlet
 
HDCSD10_TM10_TM15P-VQT2H52_eng.book  23 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							24VQT2H52
Preparation
Setup
2
Preparation of SD cards
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for motion picture 
recording.
* The SD Speed Class Rating is the speed standard for successive writes.
Product numbers correct as of July 2009. These may be subject to change.
≥4 GB or more Memory Cards that do not have 
the SDHC logo are not based on SD Memory 
Card Specifications. ≥
When the write-protect 
switch  A on SD card is 
locked, no recording, 
deletion or editing will be 
possible on the card.
≥ Keep the Memory Card out 
of reach of children to prevent swallowing.
This unit (an SDHC compatible device) is co
mpatible with both SD Memory Cards and SDHC 
Memory Cards. When using an SDHC Memory Card on another device, confirm that the device 
supports the SDHC Memory Card.
Cards that you can use with this unit
Card typeCapacityMotion picture recording
The following models of Panasonic SD cards can 
be used.Still picture 
recording
SD Memory  Card 8MB
16 MB Cannot be used. Can be 
used.
32 MB
64 MB
128 MB
256 MB
512 MB Cannot be guaranteed in operation.
The recording may suddenly stop during motion 
picture recording depending on the SD card you 
use. (
l127)
1 GB RP-SDV01G
2GB
RP-SDV02G, RP-SDM02G, RP-SDW02G, RP-SDP02G
SDHC 
Memory 
Card 4GB
RP-SDV04G, RP-SDM04G, RP-SDW04G, RP-SDP04G
6 GB RP-SDM06G
8 GB RP-SDV08G, RP-SDW08G, RP-SDP08G
12 GB RP-SDM12G, RP-SDP12G
16 GB RP-SDV16G, RP-SDW16G, RP-SDP16G
32 GB RP-SDV32G, RP-SDW32G
32
HDCSD10_TM10_TM15P-VQT2H52_eng.book  24 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							25VQT2H52
Caution:
When the SD card is removed while the access lamp is lit, this unit may malfunction or the data 
recorded on the SD card may be lost.
1Open the SD card cover by 
sliding the OPEN lever B.
≥While sliding the lever, push up on the SD card 
cover to open.
2Insert/remove the SD card.
≥Face the terminal side  C in the direction 
shown in the illustration and press it straight in 
as far as it will go.
≥ Press the center of the SD card and then pull it 
straight out.
3Return the SD card cover to its 
original position and press down 
to close.
≥Securely close it until it clicks.
≥Do not touch the terminals on the back of the SD card.
≥Do not apply strong shocks, bend, or drop the SD card.≥Electrical noise, static electricity or the failure 
of this unit or the SD card may damage or 
erase the data stored on the SD card.
≥ When the card access lamp is lit, do not:
jRemove the SD card
j Turn the unit off
j Insert and remove the USB cable
j Expose the unit to vibrations or shock
Performing the above while the lamp is on may 
result in damage to data/SD card or this unit. ≥
Do not expose the terminals of the SD card to 
water, garbage or dust.
≥ Do not place SD cards in the following areas:
jIn direct sunlight.
j In very dusty or humid areas.
j Near a heater.
j
Locations susceptible to significant difference 
in temperature (condensation can occur).
j Where static electricity or electromagnetic 
waves occur.
≥ To protect SD cards, return them to their cases 
when you are not using them.
Inserting/removing an SD card
When using an SD card not from Panasonic, or one  previously used on other equipment, for the first 
time on this unit, format the SD card. ( l89) When the SD card is formatted, all of the recorded data 
is deleted. Once the data is deleted, it cannot be restored. Copy valuable data onto a PC, DVD disc 
etc. before proceeding with the formatting. ( l96, 107)



Access lamp [ACCESS]  A≥When this unit is accessing the SD card or 
built-in memory, the access lamp lights up.


HDCSD10_TM10_TM15P-VQT2H52_eng.book  25 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							26VQT2H52
Preparation
Setup
3
Turning the unit on/off
You can turn the power on and off using the power button or by opening and closing the LCD monitor.
Press the power button to turn on the power.
AThe status indicator lights.
Power is turned on when the LCD monitor is opened,  and power is turned off when it is closed.
During normal use, opening and closing of the LCD monitor can be conveniently used to turn 
the power on/off.
∫ To turn on the power
A The status indicator lights.
∫To turn off the power
B The status indicator goes off.
In the following cases, opening the LCD monitor does not turn on the power. Press the power button to 
turn on the power. jWhen the unit is purchased
j When you have turned off the power using the power button
Turning the power on and off with the power button
To turn off the power
Hold down the power button until the status 
indicator goes off.
Turning the power on and off with the LCD monitor

When not using the unit, turn off the power using the power button.
HDCSD10_TM10_TM15P-VQT2H52_eng.book  26 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							27VQT2H52
Preparation
Setup
4
Selecting a mode
Change the mode to recording or playback.
Operate the mode switch to change the mode to   or  .
Recording mode (l42, 46)
Playback mode ( l70, 77)
HDCSD10_TM10_TM15P-VQT2H52_eng.book  27 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							28VQT2H52
Preparation
Setup
5
How to use the touch screen
You can operate by directly touching the LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with your fingers.
∫Touch
Touch and release the touch screen to select 
icon or picture.
≥Touch the center of the icon.
≥ Touching the touch screen will not operate 
while you are touching another part of the 
touch screen.
∫ About the Stylus pen
The stylus pen (supplied) can be stored on the 
unit as shown when it is not being used. Remove 
the stylus pen from the unit when it is to be used.
≥Only use the supplied stylus pen.
≥ Do not tuck the stylus pen with the LCD 
monitor.
∫ About the operation icons
///:
These icons are used to switch the menu and 
thumbnail display page, for item selection 
and setting etc.
:
Touch to return to the previous screen such 
as when setting menus
≥ Wipe the LCD monitor with a soft cloth, such 
as eye glass cleaner, when it gets dirty with 
finger prints etc.
≥ Do not touch on the LCD monitor with hard 
pointed tips, such as ball point pens.
≥ Do not touch the LCD monitor with your finger 
nails, or rub or press with strong force.
≥ It may become hard to see or hard to 
recognize the touch when the LCD protection 
sheet is affixed.
≥ Perform the touch screen calibration when the 
touch is not recognized or wrong location is 
recognized. ( l37)
HDCSD10_TM10_TM15P-VQT2H52_eng.book  28 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							29VQT2H52
Preparation
Setup
6
Using the menu screen
AIt is recommended to hold the LCD monitor with your thumb and index finger when pressing the 
buttons on the LCD monitor.
1Press the MENU button.
2Touch the top menu A.
3Touch the submenu  B.
≥Next (previous) page can be displayed by 
touching / .
≥ Information display setting is completed when 
 is surrounded by yellow after touching it.
4Touch the desired item to enter 
the setting.
5Touch [EXIT] or press the MENU 
button to exit the menu setting.
∫ About   information display 
setting
An explanation or setting confirmation message 
of the submenu or item being touched gets 
displayed in step 3 and 4.
Touch the   to cancel the information display 
setting.
HDCSD10_TM10_TM15P-VQT2H52_eng.book  29 ページ  ２００９年７月６日　月曜日　午後１時４６分 
						

							30VQT2H52
You can select the language on the screen display and the menu screen.
1Press the MENU button, then touch [SETUP] # [LANGUAGE].
2Touch [English].
Part of the menu will not be used depending on the used functions. ( l124)
Recording mode
*1 It is not displayed when the Intelligent auto mode is on.
*2 These menus are only for  /.
*3 / When the [MEDIA SELECT] is set to [SD CARD].
*4 / It will be displayed only when the [MEDIA SELECT] is set to [Built-in 
Memory].
Language selection
Menu list
RECORD SETUP
[SCENE MODE] (l 56)
[ZOOM MODE] (l 49)
[GUIDE LINES]
*1(l 57)
[REC MODE] ( l44)
[DIGITAL CINEMA]
*1(l 57)
[RELAY REC]
*4(l 58)
[FADE] ( l54)
[FADE COLOR] (l 54)
[AGS] (l 58)
[AUTO SLOW SHTR]
*1(l 59)
[FACE FRAMING] (l 59)
[BACKLIGHT COMPENS.] ( l54)
[INTELLIGENT CONTRAST]
*1(l 54)
[SOFT SKIN MODE]
*1(l 54)
[TELE MACRO] (l 54)
[MAGICPIX]
*1(l 54)
[Digital Cinema Color]
*1(l 60)
[SHOOTING GUIDE] ( l45)
[WIND CUT]
*1(l 60)
[ZOOM MIC]
*1(l 60)
[MIC LEVEL]
*1(l 61)
[PICTURE ADJUST]
*1(l 69)
[MF ASSIST]
*1(l 69)
HDCSD10_TM10_TM15P-VQT2H52_eng.book  30 ページ  ２００９年７月６日　月曜日　午後１時４６分