Panasonic Hd Integrated Camera Aw He2 Operating Instructions

11VQT4N15
Detaching and Attaching the Rear Cover
Turn the rear cover in the direction of the arrow and detach it.
1Align the mark 2 on the camera body with the mark A on the rear 
cover and insert it.
≥ Attach the rear cover with the internal stereo microphones  B facing up, and the bundling 
band eyelet  c facing down (the cover cannot be attached in the reverse order).
2Attach the rear cover by turning it in the direction of the arrow.
≥Align the middle ring portion and the mark  D on the rear cover....

12VQT4N15
Detaching and Attaching the Middle Ring Portion
Detach the middle ring portion when connecting the AC adaptor or when installing the middle 
ring portion upside down by suspending the camera from the ceiling.
≥ Detach the rear cover ( l11)
1While sliding the RELEASE lever, turn the middle ring portion in the 
direction of the arrow.
2Pull the middle ring portion out from the camera body.
1Insert the middle ring portion in the camera body.≥Insert the middle ring portion from the opposite side of...

13VQT4N15
2Turn the middle ring portion in the direction of the arrow to attach 
the middle ring portion to the camera body.
≥Turn it until there is a clicking noise and it locks into place.
∫ For ceiling-suspended installation
Mount the middle ring portion to the camera body while moving it up/down or rotating it.
1Insert the middle ring portion in the camera body.
≥Check which portions of the camera body are the top and bottom by looking at the 
positions of the internal stereo microphones  A.
≥ Insert...

14VQT4N15
Installation Instructions
Information for Your Safety
WARNING:
To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in 
accordance with the installation instructions.
WARNING:
Installation should only be performed by qualified installation personnel.
Improper installation may result in the entire apparatus falling down and causing injury.
AW-HE2PPJPJYEEJEJY_PDF_mst.book  14 ページ  ２０１２年１０月２３日　火曜日　午後５時４３分 

15VQT4N15
To installation personnel
Read the “Installation Instructions” thoroughly and then perform the operation correctly and 
safely.
Also, always read the “Information for Your Safety” (l14) of this manual as they contain 
important information.
After the installation, give the “Operating Instructions ” to the customer to save for 
future use.
Ensure that the installation work complies with the technical standards governing 
electrical equipment.
This unit is for indoor use only.
It cannot be used...

16VQT4N15
Do not install or use the unit in the following kinds of locations.
≥On walls (where the unit would be installed sideways)
≥ In locations (including places such as under  the eaves of a building) where the unit would 
be directly exposed to rain or water
≥ In locations such as kitchens where there are high concentrations of steam and grease
≥ In outdoor locations or hot places where the temperature will exceed 40 oC (104 °F)
≥ In cold locations where the temperature will drop below 0 oC (32...

17VQT4N15
≥Secure the AC adaptor firmly so that there will be no chance that it will fall off or fall down.
Secure it using a strength which can withstand the mass (approx. 0.1 kg (0.22 lb.)) of the 
AC adaptor.
Install the accessory AC adaptor near the main power outlet, and position it in such a 
way that its power plug can be plugged into and unplugged from the outlet easily.
When connecting the AC adaptor to a power outlet on the ceiling or on any other surface 
where dust may collect, wipe off the...

18VQT4N15
Be absolutely sure to read through the “Information for Your Safety” (l14) and “Installation 
precautions” ( l15 to 17).
Connect and install in the following order:
1) Checking the installation location
2) Preparing the power source
3) Connecting the cables
4) Ceiling-suspended Installation/Standing Installation/Mount to a Tripod
Checking the installation location
Refer to the illustration, and determine where the unit is to be installed and in which direction 
it should be mounted.
≥ Ensure...

19VQT4N15
Preparing the power source
Connect the AC cable to the AC adaptor and the socket.
≥The camera can also be used by connecting a USB cable. ( l9)
Connecting the cables
1Detach the rear cover and the middle ring portion. ( l11, 12)
≥Use the supplied AC adaptor. Do not use the AC adaptor of another device.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit. 
Also, do not use the AC cable from other equipment with this unit.
≥ Concerning the socket used on the...

20VQT4N15
2Pass each cable through the rear cover and the middle ring portion 
and connect them to the rear of the camera body.
≥Pass cables from the side with the middle ring portion groove ( A).
ABM3 screw (supplied)
Tightening torque: 0.882 N·m (9 kgf·cm)
C Flat washer (for M3 screw, supplied)
D Drop-prevention wire (supplied)
E AC adaptor (supplied)
F LAN cable ( l9)
G HDMI cable (optional)
H USB cable (optional)
≥ Connect this when supplying  power from the USB cable.
≥ Insert with the mark   on the...