Panasonic Hd Convertible Camera Aw He870n Operating Instructions

							- 31 -
Connection of the Indoor Pan-tilt Head AW-PH400 (continued)
When an SDI card (AW-HHD870) has been installed
  Use a coaxial cable to connect the SDI OUT connector on the SDI card and the SDI IN conne\
ctor on the AW-PH400.
  Use a coaxial cable to connect the SDI connector on the AW-PH400 to the SDI input connector on the color monitor.
  HD (1080i or 720p) analog component signals cannot be output from the \
AW-PH400.
Note
 AW-IF400 Switch settings (when the AW-RP555/AW-RP655 is used)
SW1 SW2 SET UP
1 2 3 (Tilt range) 4
OFF OFF ON OFF ON
(300 deg.) OFF
(190 deg.) OFF
System configuration (Connections) 
						

							- 32 -
System configuration (Connections)
Connection of the Indoor Pan-tilt Head AW-PH400 (continued)
*: The HD component signal cannot be output. 
Motorized zoom lens
Camera cable 
supplied with 
AW-PH400
Coaxial cable
(to SDI 
connector)
Indoor Pan-tilt 
Head
AW-PH400 HD/SD-SDI
Composite 
signal
Monitor
Protocol Converter
AW-IF400
Pan/Tilt Control 
Panel
AW-RP400
Remote 
Operation Panel
AW-CB400
Multi-Function 
Controller
AW-RP655
Multi Hybrid 
Control Panel
AW-RP555
Pan-tilt head/camera control signals
10BASE-T 
straight cable
AC Adapter
AW-PS510A
Monitor
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A
AC power cable 
supplied with 
AW-PH400
To the 
LENS I/F (1) 
connector
Iris control 
cableWhen an SDI card (AW-HHD870) has been installed
Monitor
Y
Pr
Pb
SD 
component 
signal* 
						

							- 33 -
System configuration (Connections)
Connection of the Indoor Pan-tilt Head AW-PH405
  Turn off the power of all the equipment before proceeding with the connections.
  Connect the AC power cable provided with the AW-PH405 to the AW-PH405 indoor pan-tilt head.
  Use 10BASE-T straight cables to connect the RP connectors on the pan-tilt heads with the CONTROL OUT TO PAN/TILT 
HEAD (1 to 5) connectors on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel. 
The maximum extension distance is 3281 ft. (1000 m) when using UTP category 5 cables or their equivalent.
   Connect the CONTROL OUT TO PAN/TILT HEAD terminals (P1 to P5) of the AW-RP400 and the CONTROLLER terminal of 
the protocol converter AW-IF400 using a 10BASE-T straight cable when using the AW-RP400 pan/tilt control panel.
The maximum extension distance is 1640 ft. (500 m) when using UTP category 5 cables or their equivalent.
   Connect the PAN/TILT HEAD terminal of the protocol converter AW-IF400 and the RP terminal of the AW-PH405 with a 
10BASE-T straight cable.
The maximum extension distance is 3281 ft. (1000 m) when using UTP category 5 cables or their equivalent.
  Use the camera cable provided with the pan-tilt head to connect the AW-PH405 to the unit.
   Connect the iris control cable of the motorized zoom lens to the IRIS connector on the camera, and connect the zoom/focus 
cable to the LENS I/F (1) connector on the pan-tilt head. 
						

							- 34 -
Connection of the Indoor Pan-tilt Head AW-PH405 (continued)
When an SDI card (AW-HHD870) has been installed
  Use a coaxial cable to connect the SDI OUT connector on the SDI card and the SDI IN conne\
ctor on the AW-PH405.
  Use a coaxial cable to connect the SDI connector on the AW-PH405 to the SDI input connector on the color monitor.
   When transmitting HD (1080i or 720p) analog component signals, the switch inside the AW-PH405 main unit must be set 
to the HD position (the operation of the cable compensation circuit is not involved). Consult your dealer.
Note
 AW-IF400 Switch settings (when the AW-RP400 is used)
SW1 SW2 SET UP
1234
OFF ON OFF ON OFF OFF
System configuration (Connections) 
						

							- 35 -
System configuration (Connections)
Connection of the Indoor Pan-tilt Head AW-PH405 (continued)
Motorized zoom lens
Coaxial cable
(to SDI connector)
Camera cable 
supplied with 
AW-PH405
Indoor 
Pan-tilt Head
AW-PH405HD/SD-SDI
Coaxial cable
Monitor
AC power cable 
supplied with 
AW-PH405
Protocol 
Converter
AW-IF400
Pan/Tilt 
Control 
Panel
AW-RP400
Remote 
Operation Panel
AW-CB400 Multi-Function Controller
AW-RP655
Multi Hybrid 
Control Panel
AW-RP555Pan-tilt head/camera 
control signals
10BASE-T straight cable
AC Adapter
AW-PS510AMonitor
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A Iris control 
cable
When an SDI card (AW-HHD870) has been installed
Zoom/focus 
control 
cable
To the 
LENS I/F (1) 
connector
HD/SD 
component 
signal
Monitor
Y
Pr
Pb
Composite 
signal
Coaxial cable 
						

							- 36 -
System configuration (Connections)
Connection of the Outdoor Pan-tilt Head AW-PH650
  Turn off the power of all the equipment before proceeding with the connections.
  Connect the AC adapter provided with the AW-PH650 to the AW-PH650 outdoor pan-tilt head.
  Use 10BASE-T straight cables to connect the RP connectors on the pan-tilt heads with the CONTROL OUT TO PAN/TILT 
HEAD (1 to 5) connectors on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel. 
The maximum extension distance is 3281 ft. (1000 m) when using UTP category 5 cables or their equivalent.
   Connect the CONTROL OUT TO PAN/TILT HEAD terminals (P1 to P5) of the AW-RP400 and the CONTROLLER terminal of 
the protocol converter AW-IF400 using a 10BASE-T straight cable when using the AW-RP400 pan/tilt control panel.
The maximum extension distance is 1640 ft. (500 m) when using UTP category 5 cables or their equivalent.
   Connect the PAN/TILT HEAD terminal of the protocol converter AW-IF400 and the RP terminal of the AW-PH650 with a 
10BASE-T straight cable.
The maximum extension distance is 3281 ft. (1000 m) when using UTP category 5 cables or their equivalent.
  Use the camera cable provided with the pan-tilt head to connect the AW-PH650 to the unit.
   Connect the iris control cable of the motorized zoom lens to the IRIS connector on the camera, and connect the zoom/focus 
cable to the LENS I/F (1) connector on the pan-tilt head. 
						

							- 37 -
Connection of the Outdoor Pan-tilt Head AW-PH650 (continued)
When an SDI card (AW-HHD870) has been installed
   Use a coaxial cable to connect the SDI OUT connector on the SDI card and the SDI IN conne\
ctor on the AW-PH650 main 
unit.
   Use a coaxial cable to connect the coaxial connector (SDI OUT) on the AW-PH650 to the SDI input connector on the color 
monitor.
   When transmitting HD (1080i or 720p) analog component signals, set SW2 and SW3 on the COMP circuit board to the 
HD position. The cable compensation circuit will not be activated even if SW1 is set to ON at this time so use this switch 
at the OFF setting.
  For the connections inside the housing and other details, refer to the operating instructions of the AW-PH650.
Notes
 AW-IF400 Switch settings (when the AW-RP400 is used)
SW1 SW2 SET UP
1234
OFF ON OFF ON OFF OFF
System configuration (Connections) 
						

							- 38 -
System configuration (Connections)
Connection of the Outdoor Pan-tilt Head AW-PH650 (continued)
G/L input
To be locally purchased
Pr
Outdoor 
Pan-tilt 
Head
AW-PH650HD/SD-SDI
HD/SD 
component 
signal
Monitor
D-SUB
15 pin
RJ-45 relay 
adapter
Protocol 
Converter
AW-IF400
Pan/Tilt 
Control 
Panel
AW-RP400
Remote 
Operation 
Panel
AW-CB400 Multi-Function Controller
AW-RP655
Multi Hybrid 
Control Panel
AW-RP555Pan-tilt head/camera 
control signals
10BASE-T straight cable
AC Adapter
AW-PS510AMonitor
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A
AC Adapter
AW-PS510A
Pb Y
MULTISDI
OUTPOWER
When an SDI card (AW-HHD870) has been installed
Monitor
Composite 
signal
VIDEO OUT 
						

							- 39 -
How to operate the system
Control exercised from the Remote Operation Panel AW-CB400
When using the AW-CB400, its switches and dials function as shown in the figure below.
For switching the GAIN/PED display and controller 
setting menu display.
For details on the camera’s functions, open the camera’s 
menu and select the settings.
These are the OPTION switches, and each switch makes 
it possible to operate one of the items listed below.
(The items are set on the controller setting menu.)
A: MENU  B: ENTER
C: UP  D: DOWN


For capturing the camera statuses, and synchronizing 
the data. Flashes while data is being synchronized. *1
For switching between CAM or BAR.
For adjusting the iris when IRIS is 
set to MANUAL. *4
For switching WHITE BAL ATW, A or B.
(The selected button lights.) *2
This lights when the ZOOM/FOCUS operations are 
performed using the OPTION switch or when “FAST” 
has been selected as the status of the IRIS dial 
reaction speed.
For switching DTL ON and OFF.
The LOW/HIGH selection can be made on the 
LCD menu when turned ON.
For selecting GAIN 0dB, L, M, H or AGC.
(The selected button lights.) *2
The L/M/H buttons can be set in increments of 1 dB 
between 0 dB and 18 dB on the LCD of the CB400. *3, *11
Furthermore, the MAX GAIN setting of the AGC can be 
performed from the LCD of the CB400.
For adjusting the TOTAL PEDESTAL. 
(150 to +150) *4
For switching IRIS AUTO, MANU and LOCK.
For switching the SCENE file (User/Halogen/
Fluorescent/Outdoor). (The selected button lights.)
Lights when the OPERATE switch is turned ON.
Flashes when an alarm (Fan Error) is received 
from the camera. *5
The camera can be operated 
when this switch is turned ON.
For executing AWB.
This button lights without the AWB function being 
activated when the white balance mode of the main unit 
is set to ATW, PRESET 3200K, or PRESET 5600K, or 
when the Color Bar is displayed. *6
For executing ABB. *6, *7
For adjusting R/B GAIN. (–150 to +150) *4, *8
For adjusting R/B PED. (–150 to +150) *4, *9
For selecting the cameras and pan-tilt head 
systems to be operated. 
						

							- 40 -
Control exercised from the Remote Operation Panel AW-CB400 (continued)
 *1 :  SCENE FILE, CAM/BAR, and DETAIL OFF/LOW/HIGH of each SCENE, as well as the GAINUP, AGC MAX GAIN, W/B MODE, R/B 
GAIN and T/R/B PED statuses are synchronized.
Statuses are also acquired from the camera when the SCENE is switched or when the CAMERA MENU is turned OFF (including 
switching from MENU ENABLE to DISABLE).
 *2 :   When PRESET 3200K or PRESET 5600K is selected in the camera menu, everything turns off when the camera menu is turned 
OFF.
  *3 : Everything turns off after setting 0 dB, GAIN assigned by L/M/H, or anything other than AGC on the camera’s OSD menu.
 *4 :   The R/B GAIN, R/B PED, PED, and IRIS dials are used to switch variable speeds between “Fast” and “Slow” respectively.
At the same time that the IRIS dial is pushed down, the speed at which the ZOOM/FOCUS operations are performed using the 
OPTION switch is switched between “FAST” and “SLOW”.
 *5 :   Flashing stops when communication is disconnected because the OPERATE switch has been turned OFF, CAMERA SELECT has 
been switched, the communication cable has been disconnected, etc.
 *6 :   The lamp of the ABB or AWB switch flashes while automatic white balance or automatic black balance is being executed, 
respectively. When ABB or AWB is completed successfully, the corresponding lamp goes off; when it is not completed 
successfully, it lights up.
  *7 : The switch lights without ABB being executed when the Color Bar is being displayed.
 *8 :   The R/B GAIN is cleared to zero when AWB is completed successfully.
The R/B GAIN function is not activated when the W/B mode is ATW, PRESET 3200K, or PRESET 5600K.
 *9 :   The R/B PEDESTAL is cleared to zero when ABB is completed successfully.
The R/B PED function is not activated when the W/B mode is PRESET 3200K, or PRESET 5600K.
 *10 :   The ZOOM/FOCUS operation using the OPTION switch becomes possible when the SDI card is installed without using the pan-tilt 
head.
 *11 :   In GAIN adjustment mode, the range of –6 dB to –1 dB cannot be adjusted. When a setting outside of 0 dB to 18 dB is desired, 
this can be specified in the camera menu’s gain setting (Gain).
How to operate the system