Panasonic Eyfla4 Operating Instructions Manual

- 11 -  

) Other• B i t   a n d   s o c k e t   c o n d i t i o n :   M a t e r i a l , 
amount of play, etc.
•  U s e   o f   a   u n i v e r s a l   j o i n t   o r   s o c k e t 
adapter
•  U s e r :   M a n n e r   i n   w h i c h   t h e   t o o l   i s 
applied  to  the  bolt,  strength  with  which the  tool  is  held,  manner  in  which  the tool’s switch is engaged
•  Condition of object being tightened: Ma-
terial, seating surface finish
Setting the tool to configuration mode
1.  Turn...

- 1 - 

• You  can  select  from  30  torque  clutch settings (1 to 30).
•  Use  figures  from  the  Tightening  Torque 
Chart  to  guide  your  selection  of  torque clutch setting. (See the following tighten-ing torque chart)
.  Press  the  OK  button  to  accept  the  select
-ed torque clutch setting. 
•  The  control  panel  will  stop  flashing  and 
light up.
CAUTION:
• You  must  press  the  OK  button  in  order 
for the selected setting to take effect.
•  Be  sure  to  verify  the...

- 13 -  

Snug point detection level guidelines
DisplaySnug point detection levelApplications (reference)
L1Low (Use for work characterized by low loads before the snug point is reached.)• 
Tightening  bolts  in  materials  that  are easily cracked or deformed, etc.
L
High (Use for work characterized by high loads before the snug point is reached.) • 
Tightening  bolts  in  materials  with  mis
-aligned holes, etc.
•  Tightening self-tapping screws, etc.
 
Display
Battery indication lamp
3.  Press...

- 14 - 

Radio  signal  range  limitation  function on/off  setting  (EYFLA4AR,  EYFLA5AR, EYFLA5QR, EYFLA6PR)
1. Set the tool to configuration mode.
  (See page 11.)
.  Press the format button.
•  The control panel will begin flashing.
Display: The letter “F” flashes on and off.Battery  indication  lamp:  The  upper  and lower bars of the battery flash on and off.
 
Display
Battery indication lamp
3.  Press the format button again. 
•  Radio  signal  range  limitation  function 
on/off setting...

- 15 -  

Checking tool circuits
1. Press the torque level button. 
•  Control panel display
Display: The torque set display lights up. Battery  indication  lamp:  The  middle  and lower bars of the battery flash on and off.
DisplayTool circuit
H6EYFLA4
H7EYFLA5
H8EYFLA6
H9EYFMA1
NOTE:
• If you engage the switch while a setting 
is being displayed, the control panel will revert  to  the  torque  clutch  setting  dis-play. 
CAUTION:
• The  torque  set  display  is  not  intended 
to  be  used  to...

- 16 - 

[Battery Pack]
For Appropriate Use of Bat­
tery Pack
Li­ion Battery Pack
• For optimum battery life, store the Li-ion bat-tery pack following use without charging it.
• When  charging  the  battery  pack,  confirm that  the  terminals  on  the  battery  charger are  free  of  foreign  substances  such  as  dust and  water  etc.  Clean  the  terminals  before charging the battery pack if any foreign sub-stances are found on the terminals.   The  life  of  the  battery  pack  terminals  may  be...

- 17 -  

VII.  ACCESSORIES
Charger
• EY0L80
•  EY0L81
Battery pack
• EYFB30
•  EYFB40
Remote control
• EYFA30
Protector for tool
• EYFA01-A (Blue)
•  EYFA01-Y (Yellow)
•  EYFA01-H (Gray)
•  EYFA01-G (Green)
Protector for battery
• EYFA0-H
•  EYFA04-H
Assembly Qualifier
• EYFRZ01
•  EYFR0
Federal  Communications  Commission  Interference 
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits...

- 18 - 

VIII. SPECIFICATIONS
MAIN UNIT
ModelEYFLA4EYFLA5EYFLA6EYFMA1
AARAARQQRP,JPR,JRP,J
Motor10.8 V DC14.4 V DC
Chuck sizeSingle-ended9 – 9.5 mm
(3/64" – 3/8")9 – 9.5 mm
(3/64" 
– 3/8")
□9.5 mm(3/8")□
1.7 mm 
(1/")□ 1.7 mm (1/")
Double-ended 1 mm (15/3")
1 mm
(15/3")
No load speedStage134 – 89 – 30·F
0 – 9500 – 13000 – 14500 – 1550
0 – 300
134 – 30·F
0 – 13000 – 14500 – 1550
0 – 3000 – 300
0...

- 19 -  

Remote control (not included with shipment)
ModelEYFA30
Battery voltage3 V DC
Dimensions54 mm (-1/8") × 86 mm (3-3/8") × 10 mm (13/3")
Weight (with battery) Approximately 9 g (0.6 lbs)
Assembly Qualifier (not included with shipment)
ModelEYFRZ01EYFR0
RatingSee the rating plate on the bottom of the Assembly Qualifier.
Dimensions359 mm (14-1/8") × 30 mm (9-1/16") 
× 89 mm (3-1/") 10 mm (4-3/4") × 60 mm (10-1/4") 
× 70 mm...

- 0 - 

I. CONSIGNES  DE  SECU­
RITE GENERALES
 AVERTISSEMENT!  Veuillez  lire tou­tes les instructions.
Si les instructions détaillées ci-dessous ne sont pas observées, cela peut entraîner une électro-cution, un incendie et/ou des blessures graves. Le terme “outil mécanique” utilisé dans tous les avertissements ci-dessous se réfère aux outils mécaniques opérés par cordons d'alimentation et par batterie (sans fil).
CONSERVEZ  CES  INSTRUC­
TIONS
Sécurité de la zone de travail
1) Gardez  la...