Panasonic Electronic Board UB-T780 Operating Instructions

2.
Assemble the stand. Notice
•Do not over-tighten the screw ( ). (Doing so can warp the support beams.)
• Assemble the stand so that the locking casters are on the rear side. Operating Instructions (For Basic Operations) 39 1
Installation ManualREAR
FRONT
Assemble with the holes 
toward the front.
Locking caster
side (rear) Locking 
caster side
(rear)   

3.
Pull the fall-prevention extension legs down. Note
•When folding back the fall-prevention extension legs, release the lock as follows ( ,
).
4.
Mount the elite Panaboard.
See "Assembling the elite Panaboard" (For Mounting on a Stand (Sold Separately)  ® page 44).40 Operating Instructions (For Basic Operations)
Installation Manual2
1 1 2 1
1 2  

Assembly Instructions
Preparing for Removing the elite Panaboard from Its Packaging
Open the box, remove the accessory box, and open the plastic cover of the elite Panaboard. Notice
•When handling the screen board, hold it by the edge frame and not the screen board itself.
(Holding the screen board can result in damage.)
• The packing materials in the shipping box are necessary
 for repackaging, so keep them in a safe place. Operating Instructions (For Basic Operations) 41 1
Installation ManualShipping...

Assembling the elite Panaboard
For Wall Mounting
1.
Loosely wrap the power cord with the cable tie,
and plug the power cord into the AC inlet.
•Connect the power cord to the elite Panaboard
before installing on a wall. 2.
Insert the end of the cable tie into the cable tie
fastening hole on the lower frame cover. 3.
Pull the loose end of the cable tie to tighten it,
and install the power cord depending on the
location of the outlet, as illustrated in the
following diagrams.
•When attaching the power cord...

4.
Hang the elite Panaboard on the wall mounting
plates with the screw heads. 5.
Remove the lower frame cover.
Remove the left and right screws, and then remove
the
 lower frame cover from the main unit of the elite
Panaboard. 6.
Remove the 4 latches from the board
attachment by pushing them towards the rear. 7.
Fasten to the wall.
Using the remaining 4 screws, securely fasten the
lower portion of the board attachment to the wall. 8.
Reattach the lower frame cover.
Attach the lower frame cover to the...

•
When mounting on a wall, do not hit or jolt
the elite Panaboard.
• After mounting, gently apply some weight
on the elite Panaboard to make sure that it
is securely fastened to the wall. Note
•After installation is complete, use the
included cable holder to manage the power
cord and USB cable.
9. Wipe the screen board surface.
Gently wipe the screen board surface with a soft,
moist cloth. Notice
•Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in discoloration.)
• Do...

3.
Hang the elite Panaboard on the stand with the
screw heads. 4.
Secure the elite Panaboard to the stand frame
using the two-wing bolts (M5  ´ 12 mm [1
/2 in.] [2
count]) included with the stand. Note
•After installation is complete, use the
included cable holder to manage the power
cord and USB cable. •
When installing the elite Panaboard on the
stand, you can adjust its height to 4 different
levels.
When changing the height, remove the left
and right screws from the back of the elite
Panaboard,
 and...

Confirming the elite Panaboard Operation
After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.
Action Checkpoints
Operation Measure
1 Turn on the power Green LED lights. (Normal operation)
Green LED does not light, or
red LED is blinking. Check the power cord.
See "Assembling the elite
Panaboard" (For Wall Mount-
ing ® page 42, For Mounting
on a Stand (Sold Separately)
® page 44) step 1.
Confirming the Interactive Features
1.Following the...

Repackaging
To repackage the elite Panaboard, perform steps in "Assembling the elite Panaboard" (For Wall Mounting  ®
page 42, For Mounting on a Stand (Sold Separately) ® page 44) in reverse. Package the unit as depicted in
the diagram in "Preparing for Removing the elite Panaboard from Its Packaging " (page 41).Notice
•When handling the screen board, hold it by the frame and not the screen board itself. (Holding the
screen board can result in the damage.) Operating Instructions (For...

© 2007 Panasonic Communications Co., Ltd. All Rights Reserved.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic 
products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where 
they will be accepted on a free of charge basis. Alternatively, in some...