Panasonic Electronic Board Ub-8325 Operating Instructions

91
Installation
Repacking
Perform Assembly Steps 2 through 4 on pages 86 - 88 in reverse to repack the electronic board and accessories. 
Use the joints to fasten the shipping box.
•Do not touch the screen film surface, as this may damage it.
Manuals, CD-ROM, 
Eraser cloth (for Electronic Eraser)
Markers for Interactive
Batteries (6 pcs)Pen holder (2 pcs)
Electronic Eraser Eraser
USB cable Power cordMarkers
Joints
JointsElectronic board
Thermal transfer film
[Contents of Accessory Box] Shipping box...

92
Assembling the Optional Stand (KX-BP065)
■Accessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present 
before beginning installation
.
*1The accessory wrench is required to fasten or loosen the screws  ,  ; please store it carefully for future use.
*2These are used for other models.
●
Before assembly, be sure to lock the casters.
No.Part nameIllustrationQ’tyNo.Part nameIllustrationQ’ty
Stand base 2 Wing bolt
M5 x 12 mm (
15/32”)6
Pipe...

Assembling the Optional Stand (KX-BP065)
93
Installation
■Assembly
1Assembling the stand
■Assembling the fall-prevention extension legs
The fall-prevention extension legs increase the safety of the electronic board.
•Install and always set the fall-prevention legs when using the stand.
•When tightening the screw  , hold the nut   with pliers.
Note
•When folding back the fall-prevention extension legs, release the lock as follows.
■Inserting the covers  to the pipes 
Fall-prevention extension legs•Caster...

Assembling the Optional Stand (KX-BP065)
94
■Assembling the stand
Note
*1 Do not tighten the screw   too much. This may deform the pipes.
Assemble with the holes 
toward the front.
           
Locking
casters side
(rear)Pull the fall-prevention extension legs 
down (fall-prevention extension legs 
will be fixed by the lock pin.)
1 1
1
2
Locking casters side
(rear) 

Assembling the Optional Stand (KX-BP065)
95
Installation
2Attach the fixtures   with the four wing-bolts.
3Assemble and install the electronic board.
Refer to step 3 on page 87. 

96
Optional Wall-mounting Kit (KX-B063)
Before attempting installation of this wall-mounting kit, we strongly recommend consulting with the building manager, 
engineer, or architect. The installer needs to know the type of construction used for the wall intended for this 
installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and depends on 
the nature of wall construction. Installation should not occur until this consultation takes place.
•Do not attach...

Optional Wall-mounting Kit (KX-B063)
97
Installation
■Wall-mounting procedure
1Confirm that the wall is strong enough to support the weight of the electronic board.
The wall must be capable of supporting at least 
1,005 N [103 kgf (227 lbs.)] for UB-8325.
2Tape the Wall-mounting template on the wall.
•Do not use the template included in the wall-mounting kit (KX-B063), but rather the one included with the 
electronic board (UB-8325).
•When taping the template on the wall, make sure it is level.
31) Drill...

Optional Wall-mounting Kit (KX-B063)
98
■Attaching the wall-mounting fixtures
The electronic board must be mounted with the method most suited to the material of the wall.
Three methods are presented here.
(Other options may be available in your area.)
●
Attaching to metal or concrete walls
Stud plugs (sold in stores) are needed.
Drill eight holes in the wall.
For the correct hole size, refer 
to the instructions for the 
particular stud plugs used.
Insert each bolt through a hole 
in the wall-mounting...

Optional Wall-mounting Kit (KX-B063)
99
Installation
●Attaching to plasterboard walls
Split-wing toggles (sold in stores) are needed.
●
Attaching to wooden walls
Use wood screws (sold in stores).
Insert each bolt through a hole 
in the wall-mounting fixture and 
into the hole in the wall beneath 
so that the arms of the split-
wing toggle are horizontal. For 
the correct hole size, refer to the 
instructions for the particular 
split-wing toggles used.
After the arms expand, pull the 
wall-mounting...

© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.
Printed in Malaysia
PJQXC0073ZA-F  F1205B0 Panasonic Digital Document Company,
Unit of Panasonic Corporation of North America
Two Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Panasonic Business Systems U.K.
A Division of Panasonic U.K. Ltd.
Willoughby Road, Bracknell, Berkshire, RG12 8FP
Panasonic Marketing Europe GmbH
Hagenauer Strasse 43
65203 Wiesbaden, Germany
Matsushita...