Panasonic Electronic Board Ub 5838 Operating Instructions

Assembling the unit41
Installation
■Assembly
1
Assemble the wall-mounting fixture or optional stand.
•If you are using a wall-mounting fixture, refer to “Wall-Mounting Construction” on page 48.
• If you are using a stand, refer to “Optional Stand Assembly (UE-608035)” on page 53.
2
Remove the joints and the shipping box.
•UB-5838C has 12 joints.
• UB-5338C has 8 joints.
* This is a diagram of the UB-5338C. UB-5838C has cushioning materials on the upper and lower sides of the center of the unit.
Note
•...

Assembling the unit
42
3
Collapse the carton box.
4
Remove the protective plastic bag and lay down 
the unit onto the shipping box with the screen 
film surface facing downward.
Note
• Make sure that the cushioning material and 
other packing materials do not strike the 
screen film. (Contact may damage the screen 
film.)
• When using the stand, advance to step 10.
[Wall-mounting]
5
Remove the four rivets.
Note
•To remove the rivets, turn them 
counterclockwise with a screwdriver. (The 
fixed part of the...

Assembling the unit43
Installation
7
After unscrew the 4 screws from the lower 
center frame cover, remove it.
8
Fasten the wall-mounting clasps of the unit 
securely to the wall with the 4 appropriate wall-
mounting hardware.
Note
•The 4 wall-mounting hardware are not 
included with the electronic board. Please 
purchase M6-size screws appropriate for your 
wall.
9
Attach the lower frame cover removed in step 7.
• Advance to “Electronic Board Operations Check” on 
page 45.
[Optional Stand]
10
Attach the...

Assembling the unit
44
11
Stand the unit up.
12
Attach the rivets (included in the stand) to the 
holes in the stand that are not already in use.
• normal height: 2 places
• higher than normal height: 4 places
13
Attach the clamp to the stand.
•Attach the 3 clamp for the power cord to the 
upper side of the stand, on the control box 
side.
UB5838C-PJQXC0259ZA_mst.book  44 ページ  ２００９年５月２６日　火曜日　午後２時５９分 

45
Installation
Electronic Board Operations Check
■Before Operation Check
1
Wipe the screen film surface.
•Soak a soft cloth with water, wring well, and 
wipe the screen film surface.
Note
• Do not wipe the screen film surface with paint 
thinner, benzene, or cleaners that contain 
abrasives. Doing so may cause discoloration.
• Do not wipe the screen film surface with a dry 
cloth. Doing so may create static electricity.
2
Attach the power cord.
•Securely fit the supplied power cord in the AC 
inlet of...

Electronic Board Operations Check
46
■ Operation Check Procedure
After assembling the unit and setting the time, perform the procedures presented in the following table to make sure 
it functions properly.
StepPoints to Check
ConditionSolutions
1Turn the power switch on. The standby message is displayed 
after the initial message is 
displayed. (Normal operation)
Display does not appear. Check the power cord. (See step 2 on page 45.)
An error code appears on the 
display. Contact the store or dealer from...

47
Installation
Repacking
Perform Assembly Steps 2 through 13 on pages 41 - 44 in reverse to repack the unit and accessories. Use the joints 
to fasten the shipping box.
Note
•When handling the screen unit, grasp the side cover on either side of screen. Do not grasp the screen film surface, 
as this may scratch it.
UB5838C-PJQXC0259ZA_mst.book  47 ページ  ２００９年５月２６日　火曜日　午後２時５９分 

48
Wall-Mounting Construction
■Checking the Wall
When mounting on a wall, consult with your building’s owner, caretaker or construction manager to determine if the 
wall strength is sufficient to install this unit. For safety, install this unit only after thoroughly understanding the type of  
walls, the appropriate types of screws and the construction method (page 51).
Note
• Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting 
fixture screws to metal...

Wall-Mounting Construction49
Installation
■Installing the Wall-Mounting Fixtures
1
Ensure that the wall is strong enough to support the unit.
For UB-5838C: 1,373 N [140 k gf (309 lbf)]
For UB-5338C: 1,275 N [130 k gf (287 lbf)]
2
Using the measuring tape and level, mark the 8 locations to insert the screws.
Note
• Note the difference in the hole position for UB-5838C and UB-5338C.
• Make sure that the position of the holes are level and perpendicular to each other (i.e., the unit will not be 
crooked).
•...

Wall-Mounting Construction
50
4
Install the wall-mounting  fixtures using the 4 screws.
• 2 screws are used for each wall-mounting plate.
The remaining 4 screws are used after installing the unit on the wall.
Note
• Screws (8 count) are not included with the product. Please purchase screws with a size of M6, appropriate 
for your type of wall.
• Tighten the wall-mounting hardware so that it will not become loose.
• When drilling the holes and installing the wall-mounting fixtures, follow the procedure in...