Panasonic Dvd Vcr Deck Pv D4763 Operating Instructions

							51
DV D
 Operation
You can enlarge specific portions of a JPEG picture
and select the zoom ratio using the ZOOM button
on the remote during JPEG Playback screen.
Set Zoom size.Press ZOOM repeatedly to change display as
follows.
➡
Press STOP to return to  the MP3/WMA/JPEG MENU.
You can enlarge the center portion of the image to
one of 2 magnifications.
Operation can be done during Rotation (below).
X 1.0 (ORIGINAL)
1st press2nd press 
3rd press
X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)
Use the , ,  and   buttons to move the
position up, down, left and right.
(Position cannot be changed on X1.0
ORIGINAL images.)
JPEG Zoom
JPEG Rotation
(During JPEG Playback.)
Set rotation.Press ANGLE repeatedly to change display
as below.
➡
Press STOP to return to the MP3/WMA/JPEG
MENU. (During JPEG Playback.)
You can rotate a JPEG picture using the ANGLE
button on the remote during JPEG Playback
screen. (The JPEG picture will be rotated 90 °
clockwise.)
 2nd press  3rd press Operation can be done during Zoom (above).
The vertical/horizontal ratio of rotated JPEG
images may vary when they are displayed.
 1st press
 4th press
SETFF/
SLOW+
STOP REW/
SLOW- PLAY
SELECT 
SKIP 
SKIP 
STILL
ACTION
ZOOM
ANGLE
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and
Thomson multimedia.
Windows Media, and the Windows logo are trademarks, or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
WMA is a compression format developed by Microsoft Corporation. It achieves
the same sound quality as MP3 with a file size that is smaller than that of MP3.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4751 
						

							52For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1
DVD Lock (DVD-Video only)
LEVEL 0 : LOCK ALL, Playback of  all DVDs, CDs, Video
CDs, WMA, MP3 and JPEG is prohibited.
(Use to prohibit play of mature theme DVDs not
encoded with rating level.)
LEVEL 1 : mature  theme DVDs
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 : DVDs for general audiences/children can be
played back. (DVDs with mature content
are prohibited.)
LEVEL 8 : NO LIMIT: (Factory preset)
All DVDs can be played back.
You can prevent playback of DVDs of a specific
rating level which may be unsuitable for children.
Some DVDs are encoded with a rating level. If the disc
rating is higher (stricter) than the one you preset,
playback will be prohibited.

After DVD Lock is set and a
blocked DVD is played, this
message will appear.
The message may differ
depending on the disc.
To continue viewing a blocked
program for now,
Press 
 to select “YES” and
SET. Then, enter your 4 digit
secret code (see step 3 left).
When “NO” is selected, blocked
programs cannot be viewed.
DVD Lock Feature
SELECT : 
SET : SET END : D I SPLAY,
YOUR  SELECT I ON  EXCEEDS  THE
PLAYER  S  RAT I NG  L I M I T.
DO  YOU  WANT  TO  CHANGE  THE
LIMIT?
YES
NO
Discs not encoded with rating
level will play even if the jacket
states it is for mature
audiences. For these discs, the
DVD Lock Ratings will not work.
Caution
4
Press  
to select rating level, and
press SET
to select “LOCKED” or
“UNLOCKED.”
A 4-digit code must be entered to view a blocked
program or change rating settings.
Press ACTION*
to display DVD MAIN MENU.
Press 
to select “PARENTAL LOCK,”
and
press 
SET to display.
2
1)Press NUMBER keys
to enter your secret code.
2) Enter same secret code
again for confirmation.
3)Press 
SET to display.
Step 2) not necessary when
changing rating or secret
code.
Take care that you are not
observed entering the
secret code.To Make CorrectionsPress  repeatedly to
move the cursor.
Press 
NUMBER keys to
make the correction.
Change your secret codeYou will need your current code.
Do steps 1 ~ 2 left.
Enter current secret code.
Press 
CLEAR to clear the code.
Do step 4 to enter new code.
DO NOT forget your secret code.
Note
3
DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
ST I L L   MODE : AUTO
TV  MODE : 4:3  Letterbox
PARENTAL LOCK   : LEVEL 8
*Important:If a remote control button does not work when
pressed, press the DVD button on the remote
and try the button again.
Ready Checklist
DECK is in DVD mode, press DVD.
ENTER  : 0 - 9 
END       : ACT I ON
ENTER  4-D I G I T   CODE----  
PROGRAM  RATING  EXCEEDED

2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4752 
						

							53
Disc Languages (DVD only)
To select and set the language of the audio
soundtrack, subtitles, or title/DVD menus for all discs
to be played.
“AUDIO” selections(Factory preset: English)To select the audio soundtrack language.English/Spanish/French/Japanese
Original: Original disc language
OTHER ✱✱✱✱: Other language selection*
1
“SUBTITLE” selections(Factory preset: AUTO)To select the subtitle language.AUTO:Same language selected
for “AUDIO”
If language set for “AUDIO” is used in
playback, subtitles will not appear.
If another language is used during
playback, the subtitles will appear
in the language selected at “AUDIO”
setup.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*
1
“MENUS” selections(factory preset: English)
To select the language used in title
menus or DVD menus.
English/Spanish/French/JapaneseOTHER ✱✱✱✱: Other language selection*1
To enter OTHER ✱✱✱✱
      
 code
number,
Press NUMBER keys (Please refer to
language codes on page 60).
To make corrections, press 
repeatedly to delete language code
number, and correct.
Settings for DVD Operation
1
2
Once initial settings are done, they
remain in memory (even after power off)
until changed. This means DECK will
operate under the same conditions
(especially DVDs) each time.
DISC LANGUAGES (See below)All languages offered on the disc can be set.
If the language not offered is set, the original disc
language will be selected.
AUDIO OUTPUT (See p. 54.)You can set the audio output that comes from the
digital audio output terminal.
STILL MODE (See p. 57.)To select “FIELD” (Field still) or “FRAME” (Frame
still) to prevent jitter or make small text or fine
patterns clearly visible in a still picture. When
“AUTO” is set “FIELD” or “FRAME” is selected
automatically.
TV MODE (See p. 57.)To select whether the video material for a wide-
screen will be played back in the Pan & Scan style,
Letterbox style or 16 : 9 style.
3
Press 
to select
“DISC LANGUAGES,”
and
press 
SETto display screen. Press 
ACTION
to display DVD MAIN MENU.
Press 
to select an item, and
press 
SET.
DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
ST I L L   MODE : AUTOTV  MODE : 4:3  LetterboxPARENTAL LOCK :LEVEL 8
DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
ST I L L   MODE : AUTOTV  MODE : 4:3  LetterboxPARENTAL LOCK :LEVEL 8
Press 
to select an item, and
press 
SET repeatedly
for desired language.
(Please refer right.)4
D I SC  LANGUAGES
SELECT :  
SET : SET
END : ACT I ONAUD I O : E n g l i s hSUBT I TLE : AUTO
MENUS : English
5
Press ACTION to redisplay DVD MAIN
MENU and go to step 2 to setup another
item.
Or, press 
ACTION twice to exit.*1If the selected language is not offered,
the original disc language is selected.
Ready Checklist
DECK is in DVD mode, press DVD.
DV D
 Operation
SET NUMBER
keys
CLEAR
ACTION
SELECT 
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4753 
						

							54For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Make settings according to amplifier
connected to optical audio output as shown
in above table.
*1 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or DTS
decoder, be sure to select “PCM”.
If “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.
*2 When a DTS decoder is connected, please
select “Bitstream” in “dts”.
Audio Output
Select the digital output to be output from the optical
digital audio output connector of DECK.
  
 “LPCM (DVD)” selectionsOFF:Linear PCM of less than 48 kHz/16 bit is
output. When playing DVDs recorded in linear
PCM of over 48 kHz/20 bit, no digital audio is
output. (Factory preset)
PCM:When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or more, digital audio
converted to 44.1 kHz/16 bit or 48 kHz/16 bit is
output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
  
 “Dolby Digital” selections
Bitstream:Dolby Digital bitstream (1 ch - 5.1 ch) is
output. (Factory preset)
PCM:When you have connected a amplifier that
doesn’t have a built-in Dolby Digital decoder.
  
 “dts” selectionsBitstream:DTS bitstream is output. (Factor y preset)
PCM:When you have connected a amplifier that
doesn’t have a built-in DTS decoder.
  
 “DRC (Dynamic Range Compression)”
selections
OFF:Normal audio range is selected. (Factory preset)
ON:For dynamic sound even at low volume, this is
useful for late-night listening. [Dolby Digital
DVDs only].
  
 SPEAKER SETUP
➡ See pages 55, 56, 57.
Press to select an item,
and
press 
SETrepeatedly for
output. (See below.)
Press 
to select
“AUDIO OUTPUT,”
and
press 
SETto display screen.
1
Settings for DVD Operation (continued)
3 2
4
Recommended setting
LPCM
(DVD)
PCM
PCM
PCMDolby
Digital
PCM*
1
Bitstream
BitstreamDTS
PCM*
1
PCM
Bitstream
No amplifier is connected
AV amplifier (with digital
audio input connector)
without Dolby Digital/DTS
decoder
AV amplifier including
Dolby Digital decoder
AV amplifier including
Dolby Digital/DTS decoder
*2
   Type of amplifier
   to be connected
DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
ST I L L   MODE : AUTO
TV  MODE : 4:3  Letterbox
PARENTAL LOCK :LEVEL 8
AUD I O  OUTPUT
SELECT :  
SET : SET
END : ACT I ONLPCM(DVD) : OFF
Dolby  Digital : Bitstream
dts : Bitstream
DRC : OFF
SPEAKER  SETUP
Press ACTION to redisplay DVD MAIN
MENU and go to step 2 to setup another
item.
Or, press 
ACTION twice to exit. Press 
ACTION*
to display DVD MAIN MENU.
Ready Checklist
DECK is in DVD mode, press DVD.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4754 
						

							55
*Important:If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
AUD I O  OUTPUT
SELECT :  
SET : SET
END : ACT I ONLPCM(DVD) : OFF
Dolby  Digital : Bitstream
dts : Bitstream
DRC : OFF
SPEAKER  SETUP
SPEAKER  SETUP
Speaker Size Setup
1
Speaker frequency properties and the existence of speakers is set.
Press 
to select “SPEAKER SIZE,” and press SET
to display SPEAKER SIZE screen.
Press  
to select an item, and press SET
repeatedly. (See below table.)
3 2
DV D
 Operation
SET ACTION
SELECT 
SPEAKER  SETUP
SELECT :  
SET : SET
END : ACT I ONSPEAKER  OUTPUT : MULTI-CHANNELSPEAKER  OUTPUT : MULTI-CHANNELSPEAKER  SIZE
OUTPUT  BALANCE
DELAY  TIME
Menu item
FRONT
CENTER
SURROUND
SUBWOOFERRemarkSetting
LARGE(factory preset)
SMALL
LARGE(factory preset)
SMALL
NONE
LARGE(factory preset)
SMALL
NONE
ON(factory preset)
OFFWhen the front speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the front speakers (R/L) does not support low-frequency reproduction.
When the surround speakers (R/L) supports low-frequency (under 100 Hz) reproduction.Select when the surround speakers (R/L) does not support low-frequency reproduction.
When the center speaker supports low-frequency (under 100 Hz) reproduction.
Select when the center speaker does not support low-frequency reproduction.
If there is no center speaker.
If there is no surround speaker.
If there is no subwoofer speaker. If there is a subwoofer.
SPEAKER  SIZE
SELECT :  
SET : SET
END : ACT I ONFRONTFRONT: LARGE: LARGECENTER : LARGE
SURROUND : LARGE
SUBWOOFER : ON
Press ACTION four times to exit.
Speaker Output Setup
1
Press to select “SPEAKER
SETUP,” and
press 
SET to display
SPEAKER SETUP
screen.
2
Set the number of speakers connected to the receiver
(amplifier, decoder.) (See pp. 14, 15.)
Do steps 1~3 on page 54.
Press 
to select “SPEAKER
OUTPUT,”
and
press 
SET repeatedly.
(See below.)
  
SPEAKER OUTPUT
MULTI-CHANNEL: (Factory preset)
Use this setting when 3 or more speakers are
connected. In this case, it is necessary to set
[SPEAKER SIZE], [OUTPUT BALANCE], and
[DELAY TIME].
2-CHANNEL:
When 2 speakers are connected, it is not
necessary to set [SPEAKER SIZE], [OUTPUT
BALANCE], and [DELAY TIME] (these setting
menu are not displayed.)
4Press ACTION three times to exit.
3
** If SUBWOOFER is set to “OFF,”
the front speakers are set to
“LARGE” automatically.
Do steps 1~2 of “Speaker Output Setup” above.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4755 
						

							56For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Output Balance Setup
1
Adjust the volume level output from the speakers. To adjust, play a disc or set the “TEST SIGNAL”
(p.57) to ON. Then adjust while confir ming the volume. (Even if “OFF” or NONE is set in “SPEAKER
SIZE,” the speaker OUTPUT BALANCE can still be set.)
2
Settings for DVD Operation (continued)
Delay Time Setup
1
To enjoy 5.1 CH sound, it is ideal to place all
speakers, except the subwoofer, in a circular
arrangement. (See  p. 57.)
If this is not possible, setting Delay Time gives the
sound output a delayed effect which gives you the
illusion of the ideal listening position. (See right.)
2
3
Press ACTION three times to exit.Press 
to select “OUTPUT BALANCE,” and press SET
to display OUTPUT BALANCE screen.
Press  
to select an item, and press SET repeatedly.
(See below table.)
Press 
to select “DELAY TIME,” and press SETto display DELAY TIME screen.
Press  
to select an item, and press SETrepeatedly. (See below.)
OUTPUT  BALANCE
SELECT :  
SET : SET
END : ACT I ONCENTERCENTER: 0dB: 0dBSURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB
TEST SIGNAL : OFF
Menu item
SURROUNDCENTERRemarkSetting
0ms    1ms    2ms    3ms    4ms    5ms
0ms(Factory preset) Setting a delay effect.
0ms    5ms    10ms    15ms    20ms
DistanceSettingB1
Approx. 50 cm (1   feet) 1
/2 
Approx. 100 cm (3 feet)1.3 ms
2.6 ms
3.9 ms
5.3 ms Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)
C1DistanceSetting
Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet)5.3 ms
10.6 ms
15.9 ms
Approx. 600 cm (18 feet)
B1 Center speaker
C1 Surround speaker 
,    : Delay time as 0ms
(Factory prest)

,   < : Find the distance B1, C1 in the
table (below) and change to
the recommended setting. [See  p.57.]
3Press ACTION four times to exit.
Menu item
SUBWOOFER SURROUND(L)
SURROUND(R)
CENTERRemarkSetting
-6dB
 ~ +6dB
0dB(factory preset)Adjust so that the center speaker volume is virtually the same 
level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(R) volume is virtually 
the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(L) volume is virtually 
the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the subwoofer speaker volume is optimum.
However, because no test sound will come from the 
subwoofer, play a disc to confirm, then adjust.
TEST SIGNAL : Switch test signal used for OUTPUT BALANCE setting to “OFF” or “FRONT(L)”....
➡ See page 57.
Do steps 1~2 of “Speaker Output Setup” on page 55.
Do steps 1~2 of “Speaker Output
Setup” on page 55.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4756 
						

							57
Press  to select “TV
MODE,” and press SETrepeatedly for
mode.
(See below.)2
4:3 Pan & Scan (Factor y preset) :
Wide-screen video data is played in
Pan & Scan style (left and right of screen
is trimmed.)
Video data not formatted in Pan & Scan
will play in letterbox style.
4:3 Letterbox :
Wide-screen video data is played in
Letterbox style (top and bottom of screen
has black margin).
16:9 :
Set “16:9” when using Wide-screen TV.
Press ACTIONto exit this mode.3
*Important:If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
[Letterbox]
TV Mode
Example
DV D
 Operation
[Pan & Scan (Factory preset)]
Test Signal Setup
1
This feature assists in the setting of
OUTPUT BALANCE. Starting with (L) front
speaker, a test sound is output in clockwise
order. While the test signal is output, adjust
the output of the center speaker and
Surround speaker (R/L).
(See “OUTPUT BALANCE.” P. 56.)
Press to select “TEST
SIGNAL,” and
press 
SET.
(See below.)
3Press ACTION four times to exit.
2
No sound will come from the subwoofer.
Adjust as desired when playing a disc.
While the TEST SIGNAL is output, if the
setting change in the OUTPUT BALANCE (p.
56) is under 2 seconds, the output will switch
to the next speaker. The speaker name from
which the TEST SIGNAL is currently being
output is displayed.
(Example; TEST SIGNAL : CENTER)
OUTPUT  BALANCE
SELECT :  
SET : SET
END : ACT I ONCENTER : 0dB
SURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB
TEST SIGNAL
TEST SIGNAL: OFF: OFF
Still Mode
1
Press to select “STILL MODE,”
and
press 
SET repeatedly
for mode. (See below.)
2
AUTO :“FIELD” (Field still) or “FRAME” (Frame still) is
automatically selected during the still mode.
(Factory preset)
FIELD:“FIELD” (Field still) is always selected.
This setting will reduce jitter when compared
with “AU TO” on some discs.
FRAME:“FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly
when compared with “AU T O” on some discs.
TV Mode
1
Set the screen display style for wide-screen video
material playback. Set to reduce jitter in a displayed still picture or a motion
picture.
3Press ACTION
to exit this mode.
DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
STITILLLL  MODE  MODE: AUTO: AUTOTV  MODE : 4 : 3   L e t t e r b o xPARENTAL LOCK :LEVEL 8
Press ACTIONto display DVD MAIN MENU.
Press 
ACTIONto display DVD MAIN MENU.
CENTERFRONT(R)
SUBWOOFER FRONT(L)
Listening
position
SURROUND(R)
SURROUND(L)
B1
C1
FRONT(L) CENTER FRONT(R) OFF
SURROUND(L) SURROUND(R)2sec 2sec
2sec
2sec 2sec

DVD  MA I N  MENU
SELECT :  
SET : SET
END : ACT I OND I SC  LANGUAGES
AUD I O  OUTPUT
ST I L L   MODE : AUTO
TV  MODE : 4 : 3   L e t t e r b o x
PARENTAL LOCK :LEVEL 8
Do steps 1~2 of “Output
Balance Setup” on page 56.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4757 
						

							58For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
TIMER REC
SELECT :         SET : SET
EXIT : ACT I ON PAGE : SKIP+/-
SINGLE
SLIDE
1
/3
SD Card
JPEG Playback
Still image data (JPEG) made with a digital camera, digital video camera, or PC can be played back
using an SD Memory Card/MultiMediaCard.
Compatible Card : An SD Memory Card and MultiMediaCard can be used in this DECK.
Displayable Image Formats : DCF format 1.1 compliant
Baseline JPEG format Y Cb Cr (compressed format)
(Sampling ratios  4:4:4, 4:2:0, 4:2:2, 4:1:1)
(80 x 60 ~ 5120 x 3840 pixels)
Exif2.1 image data contained in [IMEXPORT] folder used for data
transfer bitween the equipment with SD Memory Card.
JPEG files altered and saved on a PC as “grayscale” format cannot be displayed.
Some parts of an image may not be displayed or the image may be displayed on a
smaller scale depending on the size of the image.
Notes
1Insert the SD Card.
SD MENU is displayed
automatically. If SD
MENU is not displayed,
reinsert the SD Card. 
or
Press ACTION.
Press 
to select “SD CARD
PLAYBACK.”
Press SET
 to display.
During Timer REC, the above menu
is not displayed. To display the SD
Menu, reinsert the SD Card.
Note
SELECT :              EXIT          : ACTION    SET:SET
                MENU
SET  UP  VCR
SET  CLOCK
SET  UP  CHANNEL
SD  CARD  PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S  OUTPUT  CH:3
2
“SD” appears when in SD mode.
Multi Function DisplayINDEX AREA
This area is used to
display the files stored
within the SD Card.
Return to VCR Mode,
➡Press ACTION.
SD MENU DISPLAY

SINGLE PLAY
A single image, selected from the index area, can be enlarged and played back. Also, functions,
such as zoom, rotation and applying image information can be performed.
➡See “SINGLE PLAY mode” on page 59.
SLIDE SHOW
A slide show presentation can be composed, including various image transition effects and
transition speeds.
➡See “SLIDE SHOW mode” on page 59.
SINGLE PLAYSLIDE SHOW
DISPLAY
PAGE No.
Up to 1000 files can be
displayed.
Note
“SD” blinks while data is being read.
Note
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4758 
						

							59
DV D
 OperationDV D
 Operation
SINGLE PLAY mode
1
Press  to select
“SINGLE,” and press SET.
Press 
  to move
cursor to desired file in
INDEX AREA.
(Press SKIP +/
- to display
next/previous page of 9
thumbnail files),
Press SET to display file in
large size.
Press SKIP+
➡ next image.
Press SKIP-
➡ previous image.
ZOOM (Enlarge Image)Image can be displayed 2 or 4 times normal size.➡ Press ZOOM repeatedly.
ROTATEImage can be rotated clockwise in 90° increments.➡ Press ANGLE repeatedly.
Start Slide-show  ➡ Press PLAY. (See below.)
Display file information screen  ➡ Press DISPLAY.
Do steps 1 - 2 on p. 58.
2Press ACTION
to exit this mode.
SELECT  :                SET : SET
END         : ACT I ON PAGE : SKIP+/-
SINGLE
1/3
SLIDE SHOW mode
1
Do steps 1 - 2 on p. 58.
Press  to select
“SLIDE,” and press SET.
Press 
  to move
cursor to desired file in
INDEX AREA.
(Press SKIP +/
- to display
next/previous page of 9
thumbnail files).
Press SET to display
SLIDE MENU.
Press 
 to select an
item (see right), and press
SET repeatedly to set.
2
START SLIDE SHOW.
3
Press ACTION
to exit this mode.
PAUSE
Press PAUSE. ➡ Press PLAY to relese.
Press SET to return SLIDE MENU (above). SLIDE MENU
SELECT :                         SET : SET
END : ACT I ON
START
SPEED : FAST  2S
TRANSITION :   NORMAL
...
Once selected, image is displayed
  in about 3 sec. (“” appears while
  data is read. DO NOT remove SD
  Card during data reading.)
Deck buttons are inoperative.
Use remote control.
If cursor is at top of the INDEX
AREA, pressing “
” selects previous
page. If cursor is at bottom of the
INDEX AREA, pressing “
” selects
  next page.
If Rotate is operated while Zoom (X2
or X4) is displayed, the unit will revert
to X1 (ORIGINAL) magnification.
Notes
X 1.0 (ORIGINAL)
1st press2nd press 
3rd press
X 2 (ZOOM 1) X 4 (ZOOM 2)
F I LE : 12345
DATA : 05/16/2003
SIZE : 500KBYTE
PIXEL : 640✕480
ZOOM : NORMAL
ROTATE : 0.
NEXT : SKIP+
ZOOM : ZOOM
SLIDE : PLAYPREV : SKIP-
ROTATE: ANGLE
END : ACTION
File information screen
[START]
Starts slide show.
[SPEED]
FAST:
Image transition every
2 seconds.
MEDIUM:
Image transition every
5 seconds.
SLOW:
Image transition every
10 seconds.
[Transition]
NORMAL:
Image transition one by one.
WIPE:
Image transition from top to bottom.
SPLIT:
Image transition beginning at the center
and splitting to the left and right.
BLIND:
Image transition in a series of band-like
shapes that resemble window blinds.
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4759 
						

							60For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Language Code List
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or
“MENUS” (see p. 53).
   Code Language
7079Faroese
7082French
7089Frisian
7165Irish
7168Scots Gaelic
7176Galician
7178Guarani
7185Gujarati
7265Hausa
7273Hindi
7282Croatian
7285Hungarian
7289Armenian
7365Interlingua
7378Indonesian
7383Icelandic
7384Italian
7387Hebrew
7465Japanese
7473Yiddish
7487Javanese
7565Georgian
7575Kazakh
7576Greenlandic
7577Cambodian
7578Kannada
7579Korean
7583Kashmiri
7585Kurdish
7589Kirghiz
7665Latin
   CodeLanguage
7678Lingala
7679Laothian
7684Lithuanian
7686
Latvian, Lettish
7771Malagasy
7773Maori
7775Macedonian
7776Malayalam
7778Mongolian
7779Moldavian
7782Marathi
7783Malay
7784Maltese
7789Burmese
7865Nauru
7869Nepali
7876Dutch
7879Norwegian
7982Oriya
8065Panjabi
8076Polish
8083
Pashto, Pushto
8084Portuguese
8185Quechua
8277
Rhaeto-Romance
8279Romanian
8285Russian
8365Sanskrit
8368Sindhi
8372
Serbo-Croatian
8373Singhalese
   Code Language
8375Slovak
8376Slovenian
8377Samoan
8378Shona
8379Somali
8381Albanian
8382Serbian
8385Sundanese
8386Swedish
8387Swahili
8465Tamil
8469Telugu
8471Tajik
8472Thai
8473Tigrinya
8475Turkmen
8476Tagalog
8479Tonga
8482Turkish
8484Tatar
8487Twi
8575Ukrainian
8582Urdu
8590Uzbek
8673Vietnamese
8679Volapük
8779Wolof
8872Xhosa
8979Yoruba
9072Chinese
9085Zulu
   Code Language
6565Afar
6566Abkhazian
6570Afrikaans
6577Ameharic
6582Arabic
6583Assamese
6588Aymara
6590Azerbaijani
6665Bashkir
6669Byelorussian
6671Bulgarian
6672Bihari
6678
Bengali; Bangla
6679Tibetan
6682Breton
6765Catalan
6779Corsican
6783Czech
6789Welsh
6865Danish
6869German
6890Bhutani
6976Greek
6978English
6979Esperanto
6983Spanish
6984Estonian
6985Basque
7065Persian
7073Finnish
7074Fiji
2 D4763S P36-60 (030512 –§”ÔÏX2nd).p65 2003/05/14, 13:4760