Panasonic DP 3530 User Manual

							71
Function
■ General Settings
Screen
No.
15 Fold Position (A3/LDR)●-4.0 - +4.0 mm 0.0 mm
16 Fold Position (B4)●-4.0 - +4.0 mm 0.0 mm
17 Fold Position (A4/LTR-R)●-4.0 - +4.0 mm 0.0 mm
19 Language Sel. Priority Selects the display message language. Off
●Off, On
20 Date Time Setting Sets date time registered.
●Month, Day, Year, Time
21 Weekly Timer Sets the weekly On/Off timer.
22 DHCP Default Sets the DHCP.∗
Ye s
●No, Yes
23 TCP/IP Address Sets user IP address.∗
●3 digits x 4
24 TCP/IP Subnet Mask Sets the subnet mask.∗
●3 digits x 4
25 TCP/IP Default Gateway Sets the gateway address.∗
●3 digits x 4
26 DNS Server Address Sets the DNS server.∗
No
●No, Yes
27 Hard Disk Initialize Selects the HDD format/deletion. Format (Stop)
●Format, Deletion∗∗∗

For Format : No, Yes
For Deletion: Stop, Medium, High

For Medium/High: No, Yes
When elimination is executed, it differs
depending upon the data accumulation
quantity inside the hard disk, but until
operation of elimination completes, with
Medium maximum of 2 hours, maximum of 3
hours are required with High. Because at that
time, as for the knitting machine it cannot use,
when executing knitting machine talent,
please consider use frequency.
28 Hard Disk Error Check Selects the hard disk error check.∗∗
●Stop, Start Modes FunctionInitial
Setting
04/10
06/10
NOTE●The Key Operator ID Code is required before any changes can be made to items on this
page.
∗When Functions No. 22 to 26 are set, cycle the power by turning the Power Switch on the
Left side of the machine OFF and ON.
∗∗Not required in copying mode, but needed when installing options with advanced functions
(See page 81).
∗∗∗When functions No. 24 to 27 and No. 33 to 36 and 42 are set, cycle the power by turning the
Power Switch on the Left Side of the machine OFF and ON. 05/10
Downloaded From ManualsPrinter.com Manuals 
						

							72
Function
For Key Operator
■ General Settings
Screen
No.
30 Sleep/Shutdown Select Selects the Sleep/Shutdown mode. Sleep
●Sleep, Shutdown
31  Print General Settings Sets the print of general function.
●Stop, Start
32  Corona Wire Cleaning Sets the corona wire cleaning.
●Off, On
33  MAC Address Indicates the MAC address.
34  Address Book Group ID Inputs group ID for address book. 0
●0 ~ 99
35  Tandem User Parameter Inputs parameter of user machine.
36  Community Name (1) Selects to change the SNMP of Community
Name (1).∗
●Enables read only.
37  Community Name (2) Selects to change the SNMP of Community
Name (2).∗
●Enables read/write.
38  Device Name Inputs the device name when necessary.∗
(For Status Monitor/EtherTalk Machine Name)
39  Device Location Inputs the device location when necessary.∗
(For Status Monitor)
40  Daylight Time Sets the daylight time. No
●No, Yes
41  Routing Menu Function Selects the Document Distribution function∗∗
.No
●No, Yes
42  Doc. Dist. Server Name Inputs the Document Distribution System
routing server name.
43  Doc. Dist. Server IP Inputs the Document Distribution System 0.  0.  0.  0.
routing server IP address.
●3 digits x 4 Modes FunctionInitial
Setting
07/10
09/10 08/10
NOTE∗When Functions No. 36 to 39 are set, cycle the power by turning the Power Switch on the Left
side of the machine OFF and ON.
∗∗When the optional Document Distribution System (DA-WR10) is installed.
Downloaded From ManualsPrinter.com Manuals 
						

							73
Function
■ Copier Settings
Screen
No.
00 Paper Size Priority Selects paper size priority LETTER
●LEDGER, LEGAL, LETTER, LETTER-R,
INVOICE, A3, B4, A4, A4-R, B5, B5-R, A5,
8 x 13, 8.5 x 13
01 Original Mode Default Selects original setting T/P
●Text, T/P (Text/Photo), Photo
02 Text Contrast Selects contrast for Text mode 4
●1 ~ 7
03 T/P Contrast Selects contrast for Text/Photo mode 4
●1 ~ 7
04 Photo Contrast Selects contrast for Photo mode 4
●1 ~ 7 Modes FunctionInitial
Setting
01/05
NOTE●The Key Operator ID Code is required before any changes can be made to items on this page.
■ General Settings
Screen
No.Modes FunctionInitial
Setting
45 Special Paper Tray 3 Sets the Paper Tray for special paper None
(ex: colored).
●None, Tray 1, Tray 2, Tray 3, Tray 4, LCT,
Bypass
46 Special Paper Tray 4 Sets the Paper Tray for special paper None
(ex: colored).
●None, Tray 1, Tray 2, Tray 3, Tray 4, LCT,
Bypass
47 Special Paper Tray 5 Sets the Paper Tray for special paper None
(ex: colored).
●None, Tray 1, Tray 2, Tray 3, Tray 4, LCT,
Bypass
48 Data Deletion Of HD Selects the deletion level of hard disk data in Basic
every copy/print job.
●Basic, Medium, High
When the optional hard disk unit is installed,
every copy/print job data is automatically
deleted after each job is completed.
Select one of the 3 available Data deletion
security levels (Basic, Medium and High).
For higher security select Medium and High,
however, the deletion time increases with the
increase in security level, and may take
longer to erase the data. 10/10
Downloaded From ManualsPrinter.com Manuals 
						

							74
Function
For Key Operator
■ Copier Settings
Screen
No.
06 Interleaving Default Selects OHP interleaving paper Blank
●Blank, Copy
07 Page Insertion Default Selects page insertion Blank
●Blank, Copy
08 Cover Mode Default Selects cover paper F, Blank
●F, Blank, F, Copy
FB, Blank, FB, Copy
(F: Front, FB: Front + Back)
09 Job Build And SADF Mode Enables or disables the use of SADF function. Yes
●No, Yes
10 Maximum Copy Setting Determines whether to limit number of copies 0
(0-99). (No limit)
12 M1, Size Inputs a size in job memory 1 for frequently 70 x 160 mm
used size. (X)   (Y)
●X: 5~432/Y: 5~297 mm
(See page 63)
13 M2, Size Inputs a size in job memory 2 for frequently 95 x 220 mm
used size. (X)   (Y)
●X: 5~432/Y: 5~297 mm
(See page 63)
16 Memory Overflow Warning Selects the task to perform when memory Print
overflow occurs
●Print, Cancel
17  Toner Save Mode (T) Selects the toner save in Text mode. None
●None, Level 1, Level 2∗
18 Toner Save Mode (T/P) Selects the toner save in Photo/Text mode. None
●None, Level 1, Level 2∗
19 Toner Save Mode (P) Selects the toner save in Photo mode. None
●None, Level 1, Level 2∗
20 Add New Tandem Desti. Inputs a new destination to split the copy job
21 Edit Tandem Destination Edits the split copy job destination
22 Delete Tandem Desti. Deletes the split copy job destination
23 Copier Settings Print Prints the copier settings
●Stop, Start Modes FunctionInitial
Setting
04/05
05/05
NOTE●The Key Operator ID Code is required before any changes can be made to items on this page.
∗“Level 1 or 2” setting consumes less Toner than “None” setting, however, the copy quality will
diminish slightly.
Toner saving is based on the Panasonic 6 % density Test Chart (N910653):
Level 1: Uses approximately 10 % less Toner than None setting.
Level 2: Uses approximately 20 % less Toner than None setting. 03/05 02/05
Downloaded From ManualsPrinter.com Manuals 
						

							75
Function
■ Printer Settings
Screen
No.
00 Job Completion Time Sets the job completion time setting. 180
●1~ 999 sec.
01 Page Protection Compress automatically then printout. Off
●Off, On
02 Error Page Print Sets the error page printout. Off
●Off, On
03 Spool Function Sets the spool function. On
●Off, On
04 Text Print Prints text page only. On
●Off, On
05 PS Configuration Print Prints the PS status page. Start
●Stop, Start
06 Printer Settings Print Prints the printer status.
●Stop, Start
07 Font List Print (PCL) Prints the PCL font list.∗
Start
●Stop, Start
08 Font List Print (PS) Prints the PS font list.∗
Start
●Stop, Start
09 Mailbox Data Holding Sets the automatic holding period of mailbox 7 days
data.∗
●Infinity, 1 day, 2 days, 3 days, 4 days, 6 days,
7 days
10 Delete Mailbox Data Deletes the mailbox data.∗
Before
●All, Before
11 Print Queue Delete Sets the delete authorization for the print queue. Key op.
●Free, Key op. (operator)
12 AppleTalk Zone Name Inputs an AppleTalk Zone name.∗∗
●Maximum 32 characters
13 NetWare Sets the NetWare Operating System. On
●Off, On (When using IPX/SPX protocol of
Novell NetWare) Modes FunctionInitial
Setting
01/03
02/03
03/03
NOTE●The Key Operator ID Code is required before any changes can be made to items on this
page.
∗Functions No. 07 to 10 are available when the following options are installed.
Function No. 07: Printer Controller Module (DA-PC602)
Function No. 08: Multi Page Description language Controller Module (DA-MC600)
Functions No. 09 and 10: Hard Disk Drive (DA-HD60)
∗∗When Function No. 12 is set, cycle the power by turning the Power Switch on the Left Side of
the machine OFF and ON.
Downloaded From ManualsPrinter.com Manuals 
						

							76
Function
Examples
■ Changing the Auto Contrast Setting
You can select whether to automatically adjust the copying density for Text and Photo originals.
030
Scroll to
02/05
■ Changing the Paper Size
The Paper Trays are designed to accommodate Invoice, Letter, Letter-R, Legal and Ledger Size paper.
030
Paper Tray
Paper Size
■ Weekly Timer
Key Operator can administer the On/Off weekly timers.
030
End timeInput time
   Ex.: 0800
Start time
123
678
123
678
123
9
Only 3 Paper Sizes (Letter, A4,
and B5) will be available when
selecting Tray 1.
Tray 2 only
Downloaded From ManualsPrinter.com Manuals 
						

							77
Function
or
ID Code
(4-digit)
a
b
INV
LT R
LT RLGL
LDR
Pull out the Paper Tray Adjust the Paper Guides ( a / b ) Change the Paper Size Indicator
For Tray 2:
Change the position of the Paper Size
Indicator to display and to automatically
select the paper size loaded in the tray.
ID Code
(4-digit)
Scroll to
05/10
Input time
   Ex.: 1700
DP-6030
DP-6030
45
6
101112
45
6
91011
45
Note:It is recommended that the paper guide ( b ) is fixed in place with screws.
Consult an authorized service provider for details on how to fasten the guide.
Downloaded From ManualsPrinter.com Manuals 
						

							78
Function
■ Department Counter
The Department Counter feature can limit the number of copies, administer counters and Identification Code numbers for
each department. (Maximum Number of Departments: 300)
Contact your authorized service provider to enable the Department Counter feature.
Displays the sum of  all the
active department counters.For Identification Code
Select Page
Select Department
ID Code
(8-digit)
■ Network Settings
When the Parameter “23 DHCP Default” is set to “No”, the Key Operator must administer the Network settings manually.
Scroll to 05/10
or
Scroll to 06/10Input an IP Address∗
   Ex.: 192.168.1.100
When entering a 1 or 2-digit number segment, add “00” or “0” in
front of the number, to scroll to the next segment of numbers or
press the “
” key to enter a period after the number.
Examples
For Total Counter
or
or
6Input a Department Name (up to 25
characters) using the QWERTY
Keyboard and touch the OK button.
(See page 39,  How to use the
QWERTY Keyboard)
Prints all the active
department counters.
123
6
7
123
56
To clear the total counter, touch the
INPUT button, enter 0 and touch the
OK button.
Downloaded From ManualsPrinter.com Manuals 
						

							79
Function
ID Code
(4-digit)Scroll to
03/10
For Maximum Prints
Select Page
Select Department
Maximum Number
of Copies (8-digit)
DP-6030
ID Code
(4-digit)
DP-6030
Turn the Power Switch on the Left Side
of the machine OFF and ON. For Department Counter
Select Page
Select Department
Clear the
counter (8-digit)
to “0”
or
45
6
4
5
78
∗When clearing the IP address, press the  key to move to the next segment
of the IP address (
∗∗∗.∗∗∗.∗∗∗.∗∗∗) and press the Clear key.
Downloaded From ManualsPrinter.com Manuals 
						

							80
Function
Combined Function Table
Next
Selections2-SIDED/ORIG.
     COPY
SORT/
FINISHZOOM/
EFFECTSINSERTION/
OVERLAYOthers
1     1 
1     2 
2     1
2     2
Book      2 
2 Page
N in 1
Booklet
Multi-Size Feeding
Job Build and SADF
Sort
Shift-Sort
Rotate-Sort
Staple-Sort
Shift-Group
Rotate-Group
Non-Sort
Punch
Zoom
Auto Zoom
Edge
Book
Margin
Stamping
Image Repeat
Centering
Inverse
Cover
Insertion
OHP Interleaving
Presentation
Overlay
Form Overlay∗
File Edit
Interrupt
Proof Copy
Tandem Copy
Concurrent Copying
Manual Skyshot
Digital Skyshot
Double Exposure
2-SIDED/ORIG. COPY
First
Selections
SORT/
FINISH
INSERTION/OVERLAYZOOM/
EFFECTS
1      1
1      2
2      1
2      2
Book     2
2 Page
N in 1
Booklet
Multi-Size Feeding
Job Build and SADF
Sort
Shift-Sort
Rotate-Sort
Staple-Sort
Shift-Group
Rotate-Group
Non-Sort
Punch
Zoom
Auto Zoom
Edge
Book
Margin
Stamping
Image Repeat
Centering
Inverse
Cover
Insertion
OHP Interleaving
Presentation
Overlay
Form Overlay∗
File Edit
Interrupt
Proof Copy
Tandem Copy
Concurrent Copying
Manual Skyshot
Digital Skyshot
Double Exposure
: Possible Combined Functions.
: Possible Combined Functions without full size copy ratio.
: Unavailable Combined Functions.
: Next Selection is Carried Out.
: When the same function is selected twice, the second selection is ignored.
: Functional combination that cannot be performed.
: Posssible on all models except the DA-FS330.
  Multi-size Feeding with any shift function is not possible.NOTE:
A registered image cannot be 
availed in selected copy function 
of above gray highlighted.
A
R
Others
∗ Form Overlay
When the optional Hard Disk Drive Unit (DA-HD60) is not 
installed, the operation result of the Combined Function will 
change to an R.
Downloaded From ManualsPrinter.com Manuals