Panasonic Dmp B200 Owners Manual

							Getting started
VQT3C15
11
∫Detaching the battery pack
When not using for long periods of time
≥Detach the battery pack ( >above).
(Even when the unit is turned off, there is a small amount of 
voltage running through the unit, and this may result in a 
malfunction.)
≥ Recharge the battery for re-use.
∫ Recharging the battery pack
Attach the battery pack and connect the AC adaptor (>10).The [CHARGE] indicator (>8) lights while charging the battery, and 
the [CHARGE] indicator turns off when battery charging is finished.
≥ “ECO-charge”( >29) function can be used with this unit.
Charging mark is displayed for a few seconds on the lower 
right of the screen while the power is “Off”.
∫Approximate recharging and play times (Hours)
≥ Play time indicated above may differ depending on the use.
∫ Checking the remaining battery charge
Not displayed when the AC adaptor is in use.
Press [SUB MENU] while the power is “On”
Remaining charge is displayed for a few seconds at the bottom 
right of the screen.
Charge the battery pack when the display starts to flash.
≥Appears automatically when there is only a few minutes of 
charge remaining.
≥ The power may turn off without the display flashing when the 
media is played back with the battery low on charge.
Before connection, consult your car owner’s manual or your dealer.
≥Connect to the cigarette lighter socket of a vehicle that has a 12 V 
battery. It is not compatible with a vehicle that has a 24 V battery.
≥This is a special negative  grounded Car DC Adaptor. Using 
this Car DC Adaptor with a plus grounded car can cause 
malfunction and lead to fire.
1Connect the car DC adaptor to the unit.
2Connect the car DC adaptor to the cigarette 
lighter socket.
Replacing the fuse
Replace only with the specified 125 V/250 V, 3.15 A fuse. 
Use of any other type can cause fire.
1 Open the socket.
2 Replace the fuse.
3 Close the socket.
Cautions
≥To avoid draining your car battery
j
Disconnect the Car DC Adaptor from the cigarette lighter after 
use. The Car DC Adaptor continues to consume some power 
even if it is not being used, and if a battery pack is attached to 
this unit, it will start recharging which uses more power.
jDo not use the Car DC Adaptor for long periods when the 
engine is not running.
≥ Leave some slack in the cord.
≥ No responsibility will be taken for damage that occurs due to 
faulty installation.
“ECO-charge” 
is set to “On” 
“ECO-charge” 
is set to “Off”
Battery pack
Recharging*1
*1at 20 
oC (68  oF) / using headphones / LCD brightness level is “s 5” 
( > 13, “Adjusting the pictures on the LCD screen”).
Play*1,*2
*2When the battery pack is recharged setting “ECO-charge” to “Off” 
(When the battery pack is recharged setting “ECO-charge” to “On”, 
the battery duration is about 80 %.)
“ECO-charge”
“Off”“On”
DY-DB20
(supplied)43.254
DY-DB30
(optional)545
DY-DB300 (optional)75.58
RELEASE
DETACH ATTACH
Bottom side of this unit 2Slide.
1 Press and hold.
cam
Recharge
(flashing)
Fully charged
Connecting the supplied Car DC 
Adaptor
12
Car DC Adaptor (supplied)

125 V/250 V, 3.15 A type
VQT3C15~Body1_mst.fm  11 ページ  ２０１０年１２月２７日　月曜日　午後２時４分 
						

							VQT3C15
12
Turning on/off the unit
Press [POWERÍ].
The unit is turned off when [POWER Í] is pressed again.
≥ Press [POWER Í] for approx. 0.5 seconds to turn on the 
unit when the battery pack and the remote control are used.
≥ The power is shut off if the screen is closed while the power 
is “On”.
≥ When the “Automatic Standby (No Action)” is set to “On” 
(initially set to “On”), the unit will be turned off automatically 
after 15 minutes 
(5 minutes when the battery pack is used) when it is in 
stopped status ( >29).
≥ The startup will take time. The operation related to startup of 
the unit after turning on this unit can be quickened by setting 
the initial setup “Quick Start” ( >29) to “On” (initially set to 
“Off”). (The power consumption will increase)
≥ You may hear operational sounds when the unit is turned on, 
but this is due to the initialization of the pickup unit, and it is 
not a malfunction.
After opening the LCD screen and pressing [POWER Í] for 
the 1st time, a screen for the basic settings will appear.
Follow the on-screen instructions and make 
the settings with [ 3,4] and [OK].
“On-screen Language” ( >28), “Picture Quality Mode” ( >13) 
and “Quick Start” ( >29) are set.
≥You can perform this setup anytime by selecting “Easy 
Setting” in the Player Settings menu. ( >29)
≥ You can also change this setting individually. ( >13, 28, 29)
The unit is turned off automatically after set time has passed.
Switch by pressing the [OFF TIMER].
It will switch every time it is pressed.
Showing FUNCTION 
MENU
Some functions of this unit can be operated from FUNCTION 
MENU.
Press [ 3,4,2, 1] to select the item and 
press [OK].
≥ When multiple contents are recorded, select the types of 
contents or the title.
≥ If there are any other items, repeat these steps.
A Items
B Icon
To show the FUNCTION MENU screen
Press [FUNCTION MENU].
≥FUNCTION MENU also appears by pressing [SUB MENU] 
and selecting “FUNCTION MENU”.
≥Items to be displayed may vary with the media.
Easy Setting
Turn the unit off automatically
Off Timer 0 : 30
e.g., 30 min.
Off1:00
0:30 2:00 3:00 6:0012:00
!SD 
“Photos” ( >18)
“Videos (AVCHD)” ( >14)
“Videos (MPEG-2)” ( >14)
! Disc
“Videos” ( >14)
“Photos” ( >18)
“Music (MP3)” ( >20)
“Videos (AVCHD)” ( >14)
! Setup
“Player Settings” (> 26)
“LCD Menu” ( >13)
“SD Card Management” ( >17)
Remaining battery charge ( >11 )
Using the AC adaptor
0ã1
10Î1110Á0å1
110Á0ñ1
1111 0å0ê0ô0ä
DiscSetup
SD
OK
RETURN
e.g.,
DMP-B200P&PC-VQT3C15_eng.book  12 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							Getting started
VQT3C15
13
Adjusting the pictures on 
the LCD screen
1Press [LCD MENU].
≥It is also possible to display with the following 
procedures.
2Select the item with [ 3,4].
3Change the setting with [ 3,4,2,1 ].
Picture:Adjusting image quality
Monitor:Displaying images
≥When “Off” is selected, select “Yes” with [ 2,1], and then 
press [OK].
To exit the screen
Press [EXIT].
To display images when the “Monitor” is set to “Off ”
Press [LCD MENU], [SUB MENU] or [DISC/SD].
≥ Underlined items are the factory presets.
≥ If you are not using the LCD on this unit, 
select “Off”. No image mark is displayed on 
the lower left of the screen when it is set to 
“Off”.
Loading the disc or SD 
card
1Press [OPEN].
2Set the disc and close the lid.
≥Set the disc securely until you hear a click, with the 
label side up. (Double-sided disc: place the label side up 
that you want to play back)
≥Some discs may start playing when they are loaded with the 
unit turned on.
≥ About discs with a cartridge
jDVD-RAM, DVD-R: Remove the disc from the cartridge 
and set the disc in the tray. Cartridge discs cannot be used.
j Place the disc back into the cartridge for storage to prevent 
dirt and scratches after use.
≥ Do not touch the lens as it 
may make it dirty.
1Open the cover at the side of the unit.
2Insert the SD card in to the SD card slot.
≥With the label side up, insert the card straight in the 
direction shown in the figure, until you hear a sound.
3Close the cover.
To remove the cardIn step 2 above, press the center of the card until it “clicks”, and 
pull the card out straight.
1
Press [SUB MENU].
2 Select “Other Functions” with [ 3,4], and press [OK].
3 Select “LCD Menu” with [ 3,4 ], and press [OK].
! Standard: Standard
! Dynamic
: Picture with high contrast
! Night: Picture suitable for viewing in dark places
! User jBrightness:  s5 to  r5
j Color:  s5 to  r5
j Tint:  s5 to  r5
! On
:
! Off: Image display
No image
LCD Menu
PictureDynamic
MonitorOn
Brightness
Color
Tint
RETURN
SUB
MENU
Disc
SD card

Lens ( A)
DMP-B200P&PC-VQT3C15_eng.book  13 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							VQT3C15
14
Playb ack
Basic play (Playing video 
contents)
[BD-V] [DVD-V]  [DVD-VR]  [AVCHD]  [MKV]  [MPEG2]
Instructions for operations are generally described using the 
remote control in these operating instructions.
Insert a disc or SD card ( >13).
Play starts.
≥If play does not start, press [ 1](PLAY).
≥ If a media with data in different file formats is inserted, the file 
selection menu is displayed. Press [ 3,4] to select the 
desired file format and press [OK].
≥ If the menu is displayed, press [ 3,4,2,1 ] to select the 
item and press [OK].
≥ If the screen prompting you to use the color buttons appears, 
continue to operate with the color buttons on the remote 
control.
≥The producers of the disc can  control how discs are played, 
so you may not always be able to control play as described in 
these operating instructions. Read the disc’s instructions 
carefully.
≥ When playing a set of two or more BD-Video discs, the menu 
screen may continue to display even if the disc has been 
ejected.
≥ The start of playback may take time depending on the disc or 
SD card.
≥ The sound of rotation may be audible during disc playback, 
but this is not a malfunction.
∫ To adjust the volume
Press [VOL `] or [VOL_].
≥ When using headphones, turn down the volume before 
connection.
∫ Switch the media to playback
Press [DISC/SD] to select “DISC” or “SD”.
≥If a media is inserted while the unit is stopped, the drive 
switches automatically depending on the inserted media.
∫ To show menus
Press [DIRECT NAVIGATOR/TOP MENU].
≥Total title number may not be displayed properly on +R/+RW.
≥ The menu also appears by pressing [SUB MENU] and 
selecting “Top Menu” or “Menu”.
∫ To show Pop-up menu
[BD-V]
The Pop-up menu is a special feature available with some BD-
Video discs. This menu may vary with discs. For the operating 
method, refer to the instructions for the disc.
1 Press [POP-UP MENU].
2 Press [ 3,4 ,2, 1] to select the item and press [OK].
≥ Pop-up menu also appears by  pressing [SUB MENU] and 
selecting “Pop-up Menu”.
≥ Press [POP-UP MENU] to exit the screen.
∫ Displaying subtitle text
[MKV]
You can display subtitle text on MKV video disc with this unit. 
The operation might be different  or it may not operate properly 
depending on the way the file was made or the state of this unit 
(playing, stopped, etc.).
Set “Subtitle” in “Media” ( >24)
≥ MKV video files that do not display “Text” do not contain 
subtitle text.
≥ If the subtitle text is not displayed correctly, try changing the 
language settings. ( >26)
∫ Playing a title in another folder
[MKV]
1 While the “DIRECT NAVIGATOR” is displayed
Press [SUB MENU].
2 Press [ 3,4 ] to select “Select Folder” and press [OK].
3 Press [ 3,4 ] to select a folder and press [OK].
≥ You cannot select folders that contain no compatible files.
[AVCHD]  [MPEG2]
It is possible to play the HD (High Definition) video recorded on 
the Panasonic High definition Video Camera on the DVD-RAM/
R/RW/R DL/+R/+RW/+R DL or SD card, and SD (Standard 
Definition) Video recorded on the Panasonic SD Video Camera 
on the SD card.
1Insert a disc or SD card ( >13).
“Video (AVCHD)” or “Video (MPEG-2)” screen is displayed.
≥If a media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [ 3,4 ] to select “Videos (AVCHD)” or “Videos 
(MPEG-2)” and press [OK].
2Press [ 3,4,2 ,1] to select the title and 
press [OK].
≥ Total title number may not be displayed properly on +R/
+RW.
To exit the menu screen
Press [EXIT].
≥It may pause for a few seconds on the break of images when 
editing such as partial deletion is performed.
≥ High definition video (transfer rate of 18 Mbps or faster) 
cannot be played back correctly if it was recorded on a DVD 
compatible to double speed or slower.
≥ It is not possible to playback AVCHD and MPEG2 video 
which have been dragged and dropped, copied and pasted to 
the media.
DIRECT NAVIGATOR Title View
01
02
03
04
05
06
07
08
09
10 9/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7
Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri IN 2
IN 2
VHS
VHS  
 
 
IN 2
IN 2 10:00AM
11:30AM11:59PM
10:00AM 11:30AM11:59PM
10:00AM
10:30AM
11:30AM11:59PMRec. Length
No. Date Day
Channel
StartTitle NameDVD-RAM(VR)
SUB
MENU PlayPrevious NextRETURNPage  01/02
0:15 (SP)
e.g., DVD-RAM
Playing HD Video or SD Video
DIRECT NAVIGATORVideo (MPEG-2)
001
002
003
004
005
006
007
008
009
0109/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri  
 
 
10:00AM
11:30AM11:59PM
10:00AM 11:30AM11:59PM
10:00AM
10:30AM
11:30AM11:59PMRec. Length
No. Date Day
Start Title NameSD CARD
SUB
MENU PlayPrevious NextRETURNPage  01/02
0:15.47
e.g.,
DMP-B200P&PC-VQT3C15_eng.book  14 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							Playback
VQT3C15
15
[DVD-VR] [AVCHD]
1Insert a disc or SD card ( >13).
If the menu is displayed, press [ 3,4] to select the item 
and press [OK].
2Press [ 3,4] to select the title and press 
[SUB MENU].
3Press [ 3,4] to select “View Chapters” or  
“View Playlists” and press [OK].
4Press [ 3,4,2,1] to select the chapter or 
playlist and press [OK].
To display “Title View” screen
While “Playlist View” screen is displayed, press [SUB MENU] 
and select “View Titles”.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [EXIT]. These functions may not work depending on the media and 
contents.
The stopped position is memorized.
Resume play function
Press [
1] (PLAY) to restart from this position.
≥ The memorized position is cleared in the following instances:
j[∫ ] is pressed several times
j The disc or SD card is removed
j The unit is turned off due to such occurrences as power 
outage, the removal of the AC adaptor or waste of the 
battery pack’s remaining power when the unit is turned on
≥ [BD-V] : On BD-Video discs including BD-J ( >40), the resume 
play function does not work.
≥ [MKV]  [MPEG2] : The position is cleared if the unit is turned off.
≥ Press [ ;] again or [ 1] (PLAY) to restart play.
The speed increases up to 5 steps.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
≥ For some discs, the speed may not change.
Search
While playing, press [ 6] or [ 5].
≥ [DVD-VR]  [DVD-V]: Audio is heard during the first step of 
forward search.
≥ [BD-V]  [AVCHD]  [MKV]  [MPEG2] : Audio is not heard during all 
steps of search.
≥ [CD]  [MP3] : The speed is fixed to a single step.
Slow-motion
While paused, press [ 6] or [ 5].
≥ [BD-V]  [AVCHD] : Forward direction [ 5] only.
≥ [DVD-VR] : If continued for approx. 5 minutes, slow-motion play 
pauses automatically.
Skip to the title, chapter or track you want to play.
≥ Each press increases the number of skips.
≥ [MKV] : Backward direction [ :] only.
Playing chapters or playlists
Properties
 View Chapters
View Playlists
To display the title properties 
(recording date, etc.)
e.g., 
[DVD-VR]
DIRECT NAVIGATORChapter ViewSD CARD
Play
RETURN
2009.11.15
Page  01/01
001
---
---
---
---
---
---
---0:00.00002003004
005
e.g.,  [AVCHD]
Other operations during play
Stop
Pause
Search/Slow-motion
Skip
DMP-B200P&PC-VQT3C15_eng.book  15 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							VQT3C15
16
While paused, press [2] (2; ) or [ 1] (;1 ).
Each press shows the next frame.
≥ Press and hold to change in forward or backward 
succession.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
≥ [BD-V]  [AVCHD]  : Forward direction [ 1] (;1 ) only.
When black bars are shown at the top, bottom, left, and right 
sides of the screen, you can enlarge the image to fill the 
screen.
1Press [SUB MENU].
2Press [ 3,4] to select “Other Functions” 
and press [OK].
3Press [ 3,4] to select “Screen Aspect” and 
press [OK].
4Press [ 2,1] to select “Side cut” or 
“Zoom”.
≥ Please note that the top, bottom and sides of the image will 
be cut off in images with no black bars.
≥ Screen aspect will return to “Normal” in the following 
instances:
jThe drive is switched
j The unit is turned on/off
≥ [BD-V]  [DVD-V] : “Side cut” does not have any effect.
≥ When “TV Aspect” (> 28) is set to “4:3 Pan & Scan” or “4:3 
Letterbox”, the “Zoom” effect is disabled. The status messages give you information about what is 
currently being played. 
Each time you press [STATUS], the information displayed will 
change.
≥
It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Status” with [ 3,4], and press [OK].
≥ It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Other Functions” with [ 3,4], and press [OK].
3 Select “Audio” with [ 3,4], and press [OK].
[BD-V]  [DVD-V]
You can change the audio channel number each time you 
press [AUDIO] or [ 3,4 ]. This allows you to change the 
soundtrack language ( >24, “Soundtrack”), etc.
[DVD-VR]  [MKV]  [MPEG2]
AudioLR >AudioL >Audio R
^---------------------------------}
You can change soundtracks 
each time you press [AUDIO].
Frame-by-frame
Screen Aspect
! Normal: Normal output
! Side cut: The black bars on the right and left sides of 
the 16:9 image disappear and the image is 
enlarged. Please note that the right and left 
sides of the image are cut off when the 
black bar is not displayed.
! Zoom: The black bars on the top and bottom sides 
of the 4:3 image disappear and the image is 
enlarged. Please note that the top and 
bottom sides of the image are cut off when 
the black bar is not displayed.
Status messages
Changing audio
PlayBD-Video
 T1     C1     0:05.140:20.52
T:  T i t l e
C: Chapter
PL: Playlist Items change 
depending on the 
media played.
No display
Current position
Type of disc Play status
Elapsed time in the title
e.g., 
[BD-V]
Depending on the kind of media or the playback status, 
this display may not appear. To t a l  t i m e
Soundtrack 1 ENG Digital  3/2.1ch
English is selected.
e.g., 
[DVD-V]
Play DVD-RAM(VR) 
AudioLR 
 “AudioLR” 
is selected e.g.,
DMP-B200P&PC-VQT3C15_eng.book  16 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							Playback
VQT3C15
17
Enjoying picture-in-
picture in BD-Video
[BD-V]
≥These discs may not be on sale in certain regions.
≥ The usable functions and the operating method may vary 
with each disc, please refer to the instructions on the disc 
and/or visit their website.
To turn on/off secondary video
Set “Video” in “Secondary Video” to “On” or 
“Off” ( >24, Press [DISPLAY]  D “Media”   D 
“Signal Type”)
The secondary video is played.
To turn on/off secondary audio
Set “Soundtrack” in “Secondary Video” to 
“On” or “Off” ( >24, Press [DISPLAY]  D 
“Media”  D “Signal Type”)
The secondary audio is played.
≥During search/slow-motion or frame-by-frame, only the 
primary video is displayed.
≥ When “BD-Video Secondary Audio” in “Digital Audio Output” 
is set to “Off”, secondary audio will not be played even if you 
set “Soundtrack” in “Secondary Video” to “On”. Please check 
that “BD-Video Secondary Audio” is set to “On” ( >27).
≥ The playback method determined by the disc will take 
priority, so it may not play back in the manner specified with 
this unit.
≥ When the secondary video is turned off, the secondary audio 
will not be played.
∫ Formatting SD cards/Deleting data
≥If the SD card you use is formatted, all data on the card will 
be erased. It cannot be recovered.
1 Insert an SD card (> 13).
2 Press [FUNCTION MENU].
3 Press [ 2,1 ] to select 
“Setup” and press [OK].
4 Press [ 3,4 ] to select “SD 
Card Management” and 
press [OK].
5 Press [ 3,4 ] to select “BD-
Video Data Erase” or 
“Format SD Card” and press [OK].
6 Press [ 2,1 ] to select “Yes” and press [OK].
7 Press [ 2,1 ] to select “Start” and press [OK].
≥If you experience any problems, first, try formatting the SD 
card in this unit.
≥ While using this feature, do not open the cover at the side of 
the unit, touch or remove the SD card.
Primary video Secondary video
SD Card Management No. of Files    6 
Free space    300 MB 
SD card 
Format this SD Card.OK 
RETURN 
BD-Video Data Erase Format SD Card 
e.g.,
DMP-B200P&PC-VQT3C15_eng.book  17 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							VQT3C15
18
Playing still pictures
[JPEG]
Playback of the BD-RE, DVD-RAM/R/R DL or CD-R/RW with 
still pictures recorded. This unit can also play still pictures 
recorded on the SD card.
(About structure of folders  >32, “Structure of folders that can 
be played in this unit”)
1Insert a disc or SD card ( >13).
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [ 3,4 ] to select “Photos” and press [OK].
2Press [ 3,4] to select the folder and press 
[OK].
To select folders or still pictures that are played on 
slideshow.
3Press [ 3,4,2, 1] to select the still 
picture and press [OK].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [EXIT].
≥ Press [ 2,1 ] to display the previous or next still picture.
≥ Press [ :, 9 ] to show other pages.
≥ Playback is not possible for  pictures other than JPEGs.
≥ Black bars may be displayed on the top, bottom or sides 
depending on the picture aspect ratio.
≥ Still pictures displayed as  “ ” cannot be played back with 
this unit. You can display still pictures one by one at a constant interval.
1Press [SUB MENU].
≥
When “Slideshow” is displayed, press [OK].
2Press [ 3,4] to select “Start Slideshow” 
and press [OK].
To stop slideshow
Press [ ∫].
1While the “Photo View” screen is displayed 
Press [SUB MENU].
2Press [OK].
3To change the display interval
Press [ 3,4 ] to select “Display Interval” and press [ 2,1] 
to select the interval (“Long”, “Normal” or “Short”).
≥ When a still picture with a large number of pixels is 
played, the display interval may become longer. Even if 
the setting is changed, the display interval may not 
become shorter.
To set display method
Press [ 3,4] to select “Transition Effect” and press [ 2,1 ] 
to select “Fade”, “Motion” and “Random”.
To repeat slideshow
Press [ 3,4 ] to select “Repeat Play” and press [ 2,1] to 
select “On” or “Off”.
To listen to Background Music in random order 
(SD card only)
The music CD can be played back as Background Music in 
random order duri ng the slideshow.
Press [ 3,4 ] to select “Random Soundtrack” and press 
[ 2, 1] to select “On” or “Off”.
≥ You cannot search or skip on the music.
≥ When the slideshow stops, the playback of the music 
also stops.
To listen to Background Music (SD card only)
The music CD can be played back as Background Music 
during the slideshow.
Press [ 3,4 ] to select “Soundtrack” and press [ 2,1] to 
select “CD” or “Off”.
≥ You cannot search or skip on the music.
≥ When the slideshow stops, the playback of the music 
also stops.
To return to the previous screen
Press [RETURN].
Photo ViewSD card
42
Photos
Folder Name
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX XXXX
XXXXXXXX
58
105
77
48
Page UpPage Down Page 01/02
SlideshowSelect
OKRETURNRG B Y
SUB
MENU
e.g.,
Useful functions during still 
picture play
Start Slideshow
Slideshow settings
! Fade: Still pictures are changed by fading out and 
fading in.
! Motion: Still pictures are changed by fading out and 
fading in, while they are enlarged, reduced, 
or moved up or down.
! Random: In addition to the “Motion”, still pictures are 
changed by various methods.
VQT3C15~Body1_mst.fm  18 ページ  ２０１０年１２月２６日　日曜日　午前９時３１分 
						

							Playback
VQT3C15
19
1While playing
Press [SUB MENU].
2Press [3,4] to select “Screen Aspect” and 
press [OK].
3Press [ 2,1] to select “Normal” or “Side 
cut”. ( >16, “Screen Aspect”)
≥“Zoom” does not have any effect.
While playing
Press [STATUS].
Each time you press [STATUS], the information displayed will 
change.
≥ It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Status” with [ 3,4], and press [OK].
3 Press [ 2,1] to select “Off”, “Date” (Shooting date) or 
“Details” and press [OK].
A Number of the still picture in the folder / total numbers of 
the still pictures in the folder 
To exit the screen
Press [STATUS].
1While playing (except for slideshow)
Press [SUB MENU].
2Press [ 3,4] to select “Rotate Right” or 
“Rotate Left” and press [OK].
≥ The rotation information will be stored until the unit is turned 
off or the media is removed.
To change the Screen Aspect
To show the photo properties
Rotate
                                    
Date     
Size
Manufacturer
Equipment 1/2
                                    
1/1/2010     
640 x 360
e.g., “Details” screen
DMP-B200P&PC-VQT3C15_eng.book  19 ページ  ２０１０年１２月２２日　水曜日　午後６時２分 
						

							VQT3C15
20
Playing music
[CD] [MP3]
You can play generally available music CDs or MP3 files 
recorded onto a DVD-R/R DL and CD-R/RW.
(About structure of folders  >32, “Structure of folders that can 
be played in this unit”)
1Insert a disc ( >13).
“Music list” screen is displayed.
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed. Press 
[3 ,4 ] to select “Music (MP3)” and press [OK].
2Press [ 3,4] to select the track and press 
[OK].
Play starts on the selected track.
≥ Playback for some discs may start automatically.
≥ You can use search and skip functions. ( >15)
≥ The screen switches to Screen Saver mode if there is no 
operation for 2 minutes after starting playback. (Playback 
continues.) [MP3]
1While the “Music list” is displayed
Press [SUB MENU].
2Press [
3,4] to select “Select Folder” and 
press [OK].
3Press [ 3,4] to select a folder and press 
[OK].
≥ You cannot select folders that contain no compatible tracks.
To return to the previous screen
Press [RETURN].
 0.09  4.30
01
02
03
04
05
DIRECT NAVIGATORMusic listCD
No.
Track Name Play Time Track1
Track1 4min30sec 
3min41sec 
4min30sec 
3min11sec 
5min  2sec 
Track25 Tracks / Total Play Time 20min54sec
Track3
Track4
Track5
PlayRETURN
“ ” indicates the track currently playing.
e.g.,  [CD]
Playing a track in another folder
DIRECT NAVIGATORSelect Folder
CD(MP3)
    001 My favorite
        002 Brazilian pops
        003 Chinese pops
        004 Czech pops
        005 Hungarian pops
        006 Liner notes
        007 Japanese pops
        
008 Mexican pops        009 Philippine pops
        010 Swedish pops
            011 Momoko
    012 Standard number
        013 Piano solo
        014Vocal
MP3 music   F  6/25
OK RETURN
Selected folder No. 
/Total folders
If the folder has no 
track, “– –” is 
displayed as folder 
number.
e.g.,
DMP-B200P&PC-VQT3C15_eng.book  20 ページ  ２０１０年１２月２２日　水曜日　午後６時２分