Panasonic Dmc Fx48 Operating Instructions Manual

							11VQT1X57
Before Use
11 Camera ON/OFF switch (P17)
12 Zoom lever (P34)
13 Speaker (P84)
14 Microphone (P59, 76, 95)
15 Shutter button (P28, 59)
16 Mode dial (P27)
17 Hand strap eyelet•
Be sure to attach the hand strap when 
using the camera to ensure that you will 
not drop it.
18 Lens barrel
19 [COMPONENT OUT] socket (P104)
20 [AV OUT/DIGITAL] socket (P97, 99, 103)
21 Tripod receptacle
•When you use a tripod, make sure the 
tripod is stable when the camera is 
attached to it.
22 Card/Battery door (P14)
23 Release lever (P14)
24 DC coupler cover (P15) •
When using an AC adaptor, ensure that 
the Panasonic DC coupler (DMW-DCC4; 
optional) and AC adaptor (DMW-AC5PP; 
optional) are used. For connection details, 
refer to P15.
1112
13141516
18
20
19
17

2122
2324
DMC-FX48P_PC~VQT1X57_eng.book  11 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							VQT1X5712
Preparation
P reparationCharging the Battery
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BCF10PP.
•
Use the dedicated charger and battery.•This unit has a function that can distinguish useable batteries. Exclusive batteries  
(DMW-BCF10PP) are supported by this function. (Conventional batteries not supported 
by this function cannot be used)
•The battery is not charged when the camera is shipped. Charge the battery before use.•Charge the battery with the charger indoors.•Charge the battery in a temperature between 10 oC to 35 oC (50 oF to 95 oF). (The battery 
temperature should also be the same.)
It has been found that counterfeit battery packs which look very similar to the 
genuine product are made available to purchase in some markets. Some of these 
battery packs are not adequately protected with internal protection to meet the 
requirements of appropriate safety standards. There is a possibility that these 
battery packs may lead to fire or explosion. Please be advised that we are not 
liable for any accident or failure occurring as a result of use of a counterfeit 
battery pack. To ensure that safe products are used we would recommend that a 
genuine Panasonic battery pack is used.
Attach the battery paying 
attention to the direction of the 
battery.
Connect the charger to the 
electrical outlet.
•Charging starts when the [CHARGE] 
indicator  A lights green.
•Charging is complete when the 
[CHARGE] indicator  A turns off (after 
approx. 130 min maximum).
Detach the battery after 
charging is completed.
90
DMC-FX48P_PC~VQT1X57_eng.book  12 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							13VQT1X57
Preparation
∫When the [CHARGE] indicator flashes
•The battery temperature is excessively high or low. The charging time will be longer than 
normal. Also, charging may not be completed.
•The terminals of the charger or the battery are dirty. In this case, wipe them with a dry cloth.
Note
•After charging is completed, be sure to disconnect the power supply device from the electrical 
outlet.
•The battery becomes warm after using it and during and after charging. The camera also 
becomes warm during use. This is not a malfunction.
•The battery will be exhausted if left for a long period of time after being charged.•The battery can be recharged even when it still has some charge left, but it is not 
recommended that the battery charge be frequently topped up while the battery is fully 
charged. (The battery has characteristics that will reduce its operating duration and cause the 
battery to swell up.)
•When the operating time of the camera becomes extremely short even after properly charging 
the battery, the life of the battery may have expired. Buy a new battery. 
•Do not leave any metal items (such as clips) near the contact areas of the power plug. 
Otherwise, a fire and/or electric shocks may be caused by short-circuiting or the 
resulting heat generated.
∫ Battery indication
The battery indication is displayed on the LCD monitor.
[It does not appear when you use the camera with the AC adaptor (DMW-AC5PP; 
optional) connected.]
•
The indication turns red and blinks if the remaining battery power is exhausted. (The status 
indicator blinks when the LCD monitor turns off.) Recharge the battery or replace it with a fully 
charged battery.
∫ The battery life
Recording conditions by CIPA standard
•
CIPA is an abbreviation of [Camera & Imaging Products Association].•Temperature: 23 oC (73.4 oF)/Humidity: 50% when LCD monitor is on.¢
•Using a Panasonic SD Memory Card (32 MB).•Using the supplied battery.•Starting recording 30 seconds after the camera is turned on. (When the Optical image stabilizer 
function is set to [AUTO].)
•Recording once every 30 seconds  with full flash every second recording.•Rotating the zoom lever from Tele to Wide or vice versa in every recording.•Turning the camera off every 10 recordings and leaving it until the temperature of the battery 
decreases.
¢ The number of recordable pictures decreases in Auto Power LCD mode and Power LCD 
mode.
 (P23)
The number of recordable pictures varies depending on the recording interval time. 
If the recording interval time becomes longer, the number of recordable pictures 
decreases. [e.g. When recording once every 2 minutes, the number of recordable 
pictures decreases to about 87.]
About the Battery (charging/number of recordable pictures)
Number of recordable  pictures Approx. 350 pictures
By CIPA standard in Normal picture 
mode
Recording time Approx. 175 min
DMC-FX48P_PC~VQT1X57_eng.book  13 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							VQT1X5714
Preparation
The number of recordable pictures and playback time will vary depending on the 
operating conditions and storing condition of the battery.
∫ Charging
Charging time and  number of recordable pictures with the optional battery pack 
(DMW-BCF10PP) are the same as above.
The charging time  will vary slightly depending on the status of the battery and the 
conditions in the charging environment.
When the charging has been completed successfully, the [CHARGE] indicator turns off.
Note
•
The battery may swell and its operating time may become shorter as the number of times it is 
charged increases. For long term battery use, we recommend you do not frequently charge the 
battery before it is exhausted.
•The performance of the battery may temporarily deteriorate and the operating time may 
become shorter in low temperature conditions (e.g. skiing/snowboarding).
Inserting and Removing the Card (optional)/the 
Battery
•Check that this unit is turned off.•We recommend using a Panasonic card.
Slide the release lever in the direction of 
the arrow and open the card/battery door.
•Always use genuine Panasonic batteries 
(DMW-BCF10PP).
•If you use other batteries, we cannot guarantee 
the quality of this product.
Battery: Insert until it is locked by the 
lever  A being careful about the direction 
you insert it. Pull the lever  A in the 
direction of the arrow to remove the 
battery.
Card: Push it fully until it clicks being 
careful about the direction you insert it. 
To remove the card, push the card until it 
clicks, then pull the card out upright.
B: Do not touch the connection terminals of the  card.
•
The card may be damaged if it is not fully inserted.
Playback time Approx. 360 min
Charging timeApprox. 130 min maximum
CARDRY
DMC-FX48P_PC~VQT1X57_eng.book  14 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							15VQT1X57
Preparation
1:Close the card/battery door.
2 :Slide the release lever in the direction 
of the arrow.
•If the card/battery door cannot be completely 
closed, remove the card, check its direction and 
then insert it again.
Note
•Remove the battery after use. Store the removed battery in the battery case (supplied).•Do not remove the battery until the LCD monitor and the status indicator (green) turn off as the 
settings on the camera may not be stored properly.
•The supplied battery is designed only for the camera. Do not use it with any other equipment.•Before removing the card or battery, turn the camera off, and wait until the status indicator has 
gone off completely. (Otherwise, this unit may no longer operate normally and the card itself 
may be damaged or the recorded pictures may be lost.)
∫ Using an AC adaptor (optional) and a DC coupler (optional) instead of the battery
Ensure that the AC adaptor (DMW-AC5PP; 
optional) and DC coupler (DMW-DCC4; optional) 
are purchased in a set. Do not use if sold 
separately.
1 Open the card/battery door.
2 Insert the DC coupler, being careful of the 
direction.
3 Close the card/battery door.
•
Ensure that the card/battery door is closed.4Open the DC coupler cover  A.
5 Plug the AC adaptor into an electrical outlet.
6 Connect the AC adaptor  B to the [DC IN] socket 
C of the DC coupler.
D Align the marks and insert.•Ensure that only the AC adaptor and DC coupler for this 
camera are used. Using any other equipment may 
cause damage.
Note
•Always use a genuine Panasonic AC adaptor (DMW-AC5PP; optional).•Some tripods cannot be attached when the DC coupler is connected.•This unit cannot be stood upright when the AC adaptor is connected. When placing it down and 
operating, we recommend placing it on a soft cloth.
•Make sure to unplug the AC adaptor when you open the card/battery door.•If the AC adaptor and DC coupler are not necessary, then remove them from the digital 
camera. Also, please keep the DC coupler cover closed.
•Also read the operating instructions for the AC adaptor and DC coupler.•For information about optional accessories, refer to the “Digital Camera Accessory System”. 
(P126)


DMC-FX48P_PC~VQT1X57_eng.book  15 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							VQT1X5716
Preparation
About the Built-in Memory/the Card
•Memory size: Approx. 40 MB•Recordable motion pictures: QVGA (320k240 pixels) only•The built-in memory can be used as a temporary storage device when the card being used 
becomes full.
•You can copy the recorded pictures to a card. (P96)•The access time for the built-in memory may be longer than the access time for a card.
The following types of cards can be used with this unit.
(These cards are indicated as  card in the text.)
¢The SDHC Memory Card is a memory card standard decided by the SD Association in 2006 
for high capacity memory cards more than 2 GB.
¢ You can use an SDHC Memory Card in equipment that is compatible with SDHC Memory 
Cards however you cannot use an SDHC Memory Card in equipment that is only compatible 
with SD Memory Cards. (Always read the operating instructions for the equipment being 
used.)
•You can only use cards with SDHC logo (indicating compliance with the SD standard) if using 
cards with 4 GB or more capacity.
•Please confirm the latest information on the following website.http://panasonic.co.jp/pavc/global/cs (This Site is English only.)
The following operations can be performed using this unit.
•When a card has not been inserted: Pictures can be recorded in 
the built-in memory and played back.
•When a card has been inserted: Pictures can be recorded on the 
card and played back.
•Clipboard pictures (P77) are stored on the built-in memory even if a 
card is inserted.
•When using the built-in memory
k>ð (access indication¢)•When using the card
†  (access indication¢)
¢ The access indication lights red when pictures are being recorded on the built-in memory (or 
the card).
Built-in Memory
Card
Type of cardCharacteristics
SD Memory Card (8 MB to 2 GB)
(Formatted using the FAT12 or FAT16 
format in compliance with the SD 
standard)•Fast recording and writing speed•Write-Protect switch  A provided (When 
this switch is set to the [LOCK] position, 
no further data writing, deletion or 
formatting is possible. The ability to 
write, delete and format data is restored 
when the switch is returned to its 
original position.)
SDHC Memory Card (4 GB to 
32 GB)¢
(Formatted using the FAT32 format in 
compliance with the SD standard)
MultiMediaCard•Still pictures only.
2
DMC-FX48P_PC~VQT1X57_eng.book  16 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							17VQT1X57
Preparation
Note
•Do not turn this unit off, remove its battery or card or disconnect the AC adaptor 
(DMW-AC5PP; optional) when the access indication is lit [when pictures are being read 
or deleted or the built-in memory or the card is being formatted (P26)]. Furthermore, do 
not subject the camera to vibration or impact. The card or the data on the card may be 
damaged, and this unit may no longer operate normally.
•The data on the built-in memory or the card may be damaged or lost due to electromagnetic 
waves, static electricity or breakdown of the camera or the card. We recommend storing 
important data on a PC etc.
•Do not format the card on your PC or other equipment. Format it on the camera only to ensure 
proper operation. (P26)
•Keep the Memory Card out of reach of children to prevent swallowing.
Setting Date/Time (Clock Set)
•The clock is not set when the camera is shipped.
Press [MENU/SET].
Press  2/1 to select the items (year, month, 
day, hour, minute, display sequence or time 
display format), and press  3/4 to set.
A: Time at the home area
B : Time at the travel destination (P66)
‚ : Cancel without setting the clock.
•
Select either [24HRS] or [AM/PM] for the time display 
format. 
•AM/PM is displayed when [AM/PM] is selected.•When [AM/PM] is selected as the time display format, midnight is displayed as AM 
12:00 and noon is displayed as PM 12:00. This display format is common in North 
America and elsewhere.
Turn the camera on.
•The [PLEASE SET THE CLOCK] message appears. 
(This message does not appear in [PLAYBACK] 
mode.)
A [MENU/SET] button
B Cursor buttonsONOFF
/SETMENU
:
:
DMC-FX48P_PC~VQT1X57_eng.book  17 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							VQT1X5718
Preparation
Press [MENU/SET] to set.
•After completing the clock settings, turn the camera off. Then turn the camera back on, 
switch to Recording mode, and check that the display reflects the settings that were 
performed.
•When [MENU/SET] has been pressed to complete the settings without the clock having 
been set, set the clock correctly by following the “Changing the clock setting” procedure 
below.
Select [CLOCK SET] in the [REC] or [SETUP] menu, and press  1. (P20)
•It can be changed in steps 3 and 4 to set the clock.•The clock setting is maintained for 3 months using the built-in clock battery even 
without the battery. (Leave the charged battery in the unit for 24 hours to charge the 
built-in battery.)
Note
•The clock is displayed when [DISPLAY] is pressed several times during recording.•You can set the year from 2000 to 2099.•If the clock is not set, the correct date cannot be printed when you stamp the date on the 
pictures with [TEXT STAMP] (P87) or order a photo studio to print the pictures.
•If the clock is set, the correct date can be printed even if the date is not displayed on the screen 
of the camera.
Changing the clock setting
DMC-FX48P_PC~VQT1X57_eng.book  18 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							19VQT1X57
Preparation
Setting the Menu
The camera comes with menus that allow you to choose the settings for taking pictures 
and playing them back just as you like and menus that enable you to have more fun with 
the camera and use it more easily.
In particular, the [SETUP] menu contains some important settings relating to the camera’s 
clock and power. Check the settings of this menu before proceeding to use the camera.Note
Due to the camera’s specifications, it may not be possible to set some of the functions or 
some functions may not work in some of the conditions under which the camera is used.
[MODE] Playback mode menu  (P35 , 80 to  83)
A[REC]/[PLAYBACK] selector switch
•This menu lets you 
select the setting of 
the playback methods 
such as Playback or 
Slide show of only the 
pictures set as 
[FAVORITE] .
( [PLAYBACK] mode menu (P85 to 96)! [REC] mode menu (P67 to 76)
•This menu lets you 
set the protection, 
trimming or print 
settings (DPOF), etc. 
of recorded pictures.•This menu lets you 
set the Coloring, 
Sensitivity, Aspect 
ratio, Number of 
pixels and other 
aspects of the 
pictures you are 
recording.
 [SETUP] menu (P22 to 26)
•This menu lets you perform the clock settings, select the operating 
beep tone settings and set other settings which make it easier for you 
to operate the camera.
•The [SETUP] menu can be set from either the [REC MODE] or 
[PLAYBACK MODE].
DMC-FX48P_PC~VQT1X57_eng.book  19 ページ  ２００８年１２月２６日　金曜日　午後６時２５分 
						

							VQT1X5720
Preparation
This section describes how to select the Normal picture mode settings, and the same 
setting can be used for the [PLAYBACK] menu and [SETUP] menu as well.
Example: Setting [AF MODE] from [
Ø] to [š] in the Normal picture mode
Setting menu items
Turn the camera on.
A [MENU/SET] button
B [REC]/[PLAYBACK] selector switch
C Mode dial
Slide the [REC]/[PLAYBACK] selector 
switch to [ !].
•When selecting the [PLAYBACK] mode menu 
settings, set the [REC]/[PLAYBACK] selector switch to 
[( ], and proceed to step
4.
Set the mode dial to  [ ·].
Press [MENU/SET] to display the menu.
•You can switch menu screens from any menu item by 
rotating the zoom lever.
Switching to the [SETUP] menu
Press  2.
Press  4 to select the [SETUP] menu 
icon [ ].
Press  1.
•Select a menu item next and set it.
ONOFF
/SETMENU
DMC-FX48P_PC~VQT1X57_eng.book  20 ページ  ２００８年１２月２６日　金曜日　午後６時２５分