Panasonic DLP Projector PT-DZ870U PT-DW830U PT-DX100U Operating Instructions

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 131
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) Press as to select [DISPLAY SETTING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] The text display is disabled.
[TEXT] The text display is enabled.
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Change the text displayed when the text display is enabled by selecting [TEXT] in [DISPLA Y SETTING].
1) Press as to select [TEXT CHANGE].
2)  
Press the  button.
 f The  [TEXT CHANGE] screen is displayed.
3) Press  asqw to select the text, and press the  button to enter the text.
4)  
Press 
 asqw to select [OK], and press the  button.
 fThe text is changed.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1) Press  as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 f The  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] You can set the limitation on the control from the control panel.
[REMOTE CONTROL] You can set the limitation on the control from the remote control.
4) Press the  button.
 fThe  [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)  
Press 
 qw to switch the item.
 fYou can set the operation restriction from the control panel or the remote control.
[ENABLE] Enables all button operations.
[DISABLE] Disables all button operations.
[USER] Operation of all buttons can be enabled/disabled separately.
Refer to “Enabling/disabling any button” (
x
  page   131) for details.
7) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
8) Press  qw to select [OK], and press the  button.
Enabling/disabling any button
1) Press as to select [CONTROL DEVICE SETUP].   
						

							Chapter 4 Settings — [SECURITY] menu
132 - ENGLISH
2) Press the  button.
 fThe  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
4)  
Press the  button.
5)

 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch [USER].
7)
 
Press 
 as to select the button item to set.
 fWhen [INPUT  SELECT BUTTON] is selected, press the  button, and then press as to select the button to set.
Buttons that can be set
[CONTROL PANEL] [REMOTE CONTROL]
[POWER BUTTON] Power standby  button, power on  button
[INPUT SELECT BUTTON]  button,  button, or  button,  button,  button, 
 button, and  button 
*1
[MENU BUTTON]
 button
[LENS BUTTON]  button Lens (, , ) button
[AUTO SETUP BUTTON]  button
[SHUTTER BUTTON]  button
[ON SCREEN BUTTON] — button
[OTHER BUTTON] asqw,  button Buttons not listed above
*1 Only for PT-
DZ870U
8) Press qw to switch the item.
[ENABLE] Enables button operations.
[DISABLE] Disables button operations.
 fThe following items are available only when [RGB1/2 BUTT

ON] of [INPUT SELECT BUTTON] is selected.
[TOGGLE]Switches between RGB1 and RGB2 when the button is operated.
[RGB1] Fixes to RGB1.
[RGB2] Fixes to RGB2.
[DISABLE] Disables button operations.
 fWhen [INPUT

 SELECT BUTTON] is selected in Step 7), and after the item is switched, press the  button to return to the 
[CONTROL PANEL] screen or the [REMOTE CONTROL]  screen.
9) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
10) Press  qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the  [CONTROL  DEVICE PASSWORD] screen is displayed.
Enter the control device password.
 f The 

[CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 fIf the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.
 f Even when button operation on the remote control is disabled, operation of the  button on the remote control is enabled.   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 133
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1) Press as to select [CONTROL DEVICE PASSWORD CHANGE].
2)  
Press the  button.
 f The  [CONTROL DEVICE PASSWORD CHANGE]  screen is displayed.
3) Press asqw to select the text, and press the  button to enter the text.
4)  
Press 
 asqw to select [OK], and press the  button.
 fTo cancel, select [CANCEL].
Attention
 fThe initial password is “AAAA” by the factory default or when [ALL  USER DA TA] in [INITIALIZE] (x   page   123) is executed. fChange the password periodically that is hard to guess.   
						

							Chapter 4 Settings — [NETWORK] menu
134 - ENGLISH
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an i\
tem from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[DIGITAL LINK MODE]
Switch the communication method of the  terminal of the projector.
1) Press  as to select [DIGITAL LINK MODE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Switches the communication method automatically to DIGITAL LINK or Ethernet.
[DIGITAL LINK] Fixes the communication method to DIGITAL LINK.
[ETHERNET] Fixes the communication method to Ethernet.
Possible communication modes
Setting Communication possible
Image transmission EthernetRS
- 232C
[AUTO] For DIGITAL LINK
lll
For Ethernet ―
l―
[DIGITAL LINK] lll
[ETHERNET] ―
l―
l: Communication possible
―: Communication not possible
[DIGITAL LINK SETUP]
Set the communication method of DIGITAL LINK.
When the projector is connected directly via Ethernet
1) Press  as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(ETHERNET)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[AUTONEGOTIATION] The communication method is set automatically.
[100BaseTX-Full] Full duplex communication method is set.
[100BaseTX-Half] Half-duplex communication method is set.
5) Press as to select [STORE].
6)  
Press the  button.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 135
7) When the confirmation screen is displayed, press qw  to select [OK], and press the  button.
Note
 f The projector does not support 10BaseT  Full/Half.
When the projector is connected to a twisted-pair-cable transmitter
1) Press as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(DIGITAL LINK)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[100BaseTX-Full] Full duplex communication method is set.
[100BaseTX-Half] Half-duplex communication method is set.
[AUTONEGOTIATION] The communication method is set automatically.
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[DIGITAL LINK STATUS]
Display DIGITAL LINK connection environment.
1) Press as to select [DIGITAL LINK STATUS].
2)  
Press the  button.
 f The  [DIGITAL LINK STATUS] screen is displayed.
[LINK STATUS] Either [NO LINK], [DIGITAL LINK], or [ETHERNET] is displayed.
[HDCP STATUS] Either [NO SIGNAL], [OFF], or [ON] is displayed.
[SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to 
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter
.
 fMAX/MIN: Maximum/minimum value of the amount of error

.
 fGreen (-12 dB or lower)  →  Normal signal quality level.
 fY

ellow (
-11 to -8 dB) → Warning level where there is the possibility of noise introduced on the 
screen.
 f Red (-7 dB or higher) → Abnormal level where synchronization may be interrupted, or a signal may 
not be received.
[NETWORK SETUP]
Perform the initial setting of the network before using the network function.
1) Press  as to select [NETWORK SETUP].
2)  
Press the  button.
 f The  [NETWORK SETUP] screen is displayed.
3) Press  as to select an item, and change the settings according to the operation i\
nstructions of the 
menu.
[PROJECTOR NAME] Change the setting when using a DHCP server.
[DHCP] Set to [ON] when obtaining an IP address automatically using a DHCP server. Set to [OFF] when not 
using a DHCP server.
[IP ADDRESS] Enter the IP address when not using a DHCP server.
[SUBNET MASK] Enter the subnet mask when not using a DHCP server.
[DEFAULT GATEWAY] Enter the default gateway address when not using a DHCP server.
[STORE] Save the current network settings.   
						

							Chapter 4 Settings — [NETWORK] menu
136 - ENGLISH
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f When using a DHCP  server, confirm that the DHCP server is running. fConsult your network administrator regarding the IP
 address, subnet mask, and default gateway.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press as to select [NETWORK CONTROL].
2)  
Press the  button.
 f The  [NETWORK CONTROL] screen is displayed.
3) Press  as to select an item, and press qw to change the setting.
[WEB CONTROL] Set to [ON] to control with the web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the / terminal control command format 
(x
  page   175). Refer to “Control commands via LAN” ( x
  page   170).
[COMMAND PORT] Set the port number used for command control.
[CRESTRON RoomView] Set to [ON] to control with RoomView of Crestron Electronics, Inc.
[AMX D.D.] Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to 
the website of AMX Corporation.
URL http://www.amx.com/
[EXTRON XTP] Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the  
terminal.
The [EXTRON XTP] setting must be set to [OFF] when connecting the optional Digital Interface Box 
(Model No.: ET
-

YFB100G).
For details of the “XTP transmitter”, refer to the website of Extron Electronics.
URL http://www.extron.com/
[STORE] Save the current network control settings.
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[NETWORK STATUS]
Display the status of the projector network.
1) Press as to select [NETWORK STATUS].
2)  
Press the  button.
 f The  [NETWORK STATUS] screen is displayed.
[DIGITAL INTERFACE BOX]
When the optional Digital Interface Box (Model No.: ET- YFB100G) is connected to the  terminal, the main menu of 
ET- YFB100G is displayed. Refer to the Operating Instructions of ET- YFB100G for details.
Note
 fWhen [EXTRON XTP] is set to [ON], [DIGIT AL INTERFACE BOX] cannot be selected. fThe operation guidance for the “RETURN” button is displayed on the menu screen of the Digital Interface Box.  The projector does not have 
the “RETURN” button, but same operation is available with the  button.
[Art-Net SETUP]
Settings to use the Art-Net function is executed.
1) Press  as to select [Art-Net SETUP].
2)  
Press the  button.
 f The  [Art-Net SETUP] screen is displayed.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 137
3) Press as to select an item.
[Art-Net] Sets to [ON] when the Art-Net function is used. Sets to [OFF] when the Art-Net function is not used.
[PORT ADDRESS] Inputs a port address that the projector processes Art-Net.
[START ADDRESS] Inputs a start address that the projector processes Art-Net.
4) Press qw to switch the setting.
5)  
Press 
 as to select [STORE], and press the  button.
6)
 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Network connections
The projector has a network function, and the following operations are available from the computer using the web control.
 fSetting and adjustment of the projector
 fDisplay of the projector status
 fSending of E-mail messages when there is a problem with the projector
The projector supports “Crestron RoomV

iew”, and the following application software of Crestron Electronics, Inc. can be used.
 fRoomV

iew Express
 fFusion R

V
 fRoomV

iew Server Edition
Attention
 fWhen a LAN cable is directly connected to the projector , the network connection must be made indoors.
Note
 f“Crestron RoomV iew” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems 
connected to a network using a computer.
 f For details of “Crestron RoomV

iew”, refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com
To download “RoomView Express”, go to the following website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com/getroomview
 f A

 LAN cable is required to use the network function.
 rExample of a normal network connection
Computer
Projector
LAN cable (straight) LAN cable (straight) Hub
 fA web browser is required to use this function. Confirm that the web browser can be used beforehand.
Compatible OS: Windows XP/Windows Vista/Windows 7/Windows 8, Mac OS   X   v10.4/v10.5/v10.6/v10.7/v10.8
Compatible browser: Internet Explorer 7.0/8.0/9.0/10.0, Safari 4.0/5.0/6.0 (Mac OS)
 f Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
 fUse a LAN cable that is compatible with category 5 or higher

.
 fUse a LAN cable of 100

  m (328'1") or shorter.
Connecting to a twisted-pair-cable transmitter
The projector has a function that can receive Ethernet signals from a twisted-pair-cable transmitter together with video and audio signals via a 
LAN cable. Connect a LAN cable to the  terminal of the projector. (x pages 18, 28)   
						

							Chapter 4 Settings — [NETWORK] menu
138 - ENGLISH
 rExample of network connections via a twisted-pair-cable transmitter
Computer
Projector
LAN cable (straight) LAN cable (straight)
LAN cable (straight)
Twisted-pair-cable transmitter
Hub
 f
For the LAN cable between a twisted-pair-cable transmitter and the projector , use a cable that meets the following criteria:
 gCompatible with CA

T5e or higher
 gShielded type (including connectors)
 gStraight-through
 gSingle wire
 fThe maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100

  m (328'1"). If this distance is 
exceeded, image may be disrupted and may cause a malfunction in LAN communication.
 f When laying cables between a twisted-pair-cable transmitter and the projector , check that cable characteristics are compatible with CA

T5e 
or higher using tools such as a cable tester or cable analyzer.
When using a relay connector midway, include it in the measurement.
 f Do not use a hub between a twisted-pair-cable transmitter and the projector .
 fDo not pull cables forcefully

. Also, do not bend or fold cables unnecessarily.
 fT

o reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector 
without any loops.
 f Lay the cables between a twisted-pair-cable transmitter and the projector away from other cables, particularly power cables.
 fWhen installing multiple cables, run them side by side along the shortest distance possible without bundling them together .
 fAfter laying the cables, confirm that the value of [SIGNAL

 QUALITY] in the [NETWORK] menu → [DIGITAL LINK STATUS] is displayed in 
green (indicates normal quality). ( x
  page   135)
 fFor twisted-pair-cable transmitter of other manufacturers of which the operation has been verified with the DIGIT AL

 LINK compatible 
projector, refer to Panasonic website (http://panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers 
has been made for the items set by Panasonic Corporation, and not all the operations have been verified. For operation or performance 
problems caused by the devices of other manufacturers, contact the respective manufacturers.
Accessing from the web browser
1) Start up the web browser on the computer .
2)  
Enter the IP
  address set on the projector into the URL entry field of the web browser.
3)
 
Enter the user name and the password.
 f The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower 
case).   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 139
4) Click OK.
 fThe [Projector status] page is displayed.
Note
 fIf you use a web browser to control the projector , set [WEB CONTROL] to [ON] in [NETWORK CONTROL] ( x   page   136). fDo not perform setting or control simultaneously by starting up multiple web browsers. Do not set or control the projector from multiple 
computers.
 fChange the password first. ( x

  page   152)
 fThe administrator rights allow use of all functions. 

The user rights allow use of [Projector status] (x   page   140), confirmation of the error 
information page ( x
  page   141), [Network status] (x   page   142), [Basic control] (x   page   143), and [Change password] (x
  page   152) 
only.
 f Access will be locked for few minutes when an incorrect password is entered three times consecutively . fSome items on the projector setting page use the Javascript function of the web browser . 

The projector may not be able to be controlled 
properly if it is set with a browser that does not have this function enabled.
 f If the screen for the web control is not displayed, consult your network administrator . fWhile updating the screen for the web control, the screen may become white for a moment, but it is not a malfunction.
Descriptions of items
1
2
3
4
5
6
1 Page tab
Switches pages by clicking this item.
2
 
[Status]
The status of the projector is displayed by clicking this item.
3

 
[Projector control]
The [Projector control] page is displayed by clicking this item. 4

 [Detailed set up]
The [Detailed set up] page is displayed by clicking this item.
5
 
[Change password]
The [Change password] page is displayed by clicking this item.
6

 
[CRESTRON RoomV
 iew]
The control page of RoomView is displayed by clicking this item.   
						

							Chapter 4 Settings — [NETWORK] menu
140 - ENGLISH
[Projector status] page
Click [Status] → [Projector status].
Display the status of the projector for the following items.
13
14
156
7
8
1
2
3
4
16 9
5 10
11
12
1 [PROJECTOR TYPE]
Displays the type of the projector.
2
 
[MAIN VERSION]
Displays the firmware version of the projector

.
3
 
[POWER]
Displays the status of the power

.
4
 
[SHUTTER]
Displays the status of the shutter (ON: closed, OFF: open).
5

 
[LAMP
  SELECT]
Displays the setting status of [LAMP SELECT] (x
  page   109).
6
 
[SERIAL
  NUMBER]
Displays the serial number of the projector.
7
 
[REMOTE2 ST
 ATUS]
Displays the control status of the  terminal.
8
 
[OSD]
Displays the status of the on-screen display

.9
 [LAMP  POWER]
Displays the setting status of [LAMP POWER] (x   page   111).
10
 
[INPUT]
Displays the status of the selected input.
11
 [INT

AKE AIR TEMPERATURE]
Displays the status of the air intake temperature of the projector.
12
 
[OPTICS MODULE TEMPERA
 TURE]
Displays the status of the internal temperature of the projector .
13
 
[AROUND LAMP
  TEMPERATURE]
Displays the status of the temperature around the lamp of the 
projector.
14
 
[LAMP1], [LAMP2], [RUNTIME]
Displays the status and the runtime (converted value) of the 
lamp.
15

 
[SELF TEST]
Displays the self-diagnosis information.
16

 
[PROJECT
 OR RUNTIME]
Displays the runtime of the projector.