Panasonic DLP Projector PT-DZ21KU PT-DS20KU PT-DW17KU Operating Instructions

[PROJECTOR SETUP] menu
ENGLISH - 101
Settings
Note
 zFor a set time after [LAMP

 SELECT] is switched, 
[LAMP SELECT] cannot be switched again, 
because the speed of the lamp replacement cycle 
will increase. Repeatedly switching [LAMP SELECT] 
in a short time will also increase the speed of the 
lamp replacement cycle.
 z The colors of the items indicate the status.
Green → Current setting
Y

ellow → Current setting
(When there is a lamp that cannot turn on or failed 
to turn on)
Red → Lamp that has...

[PROJECTOR SETUP] menu
102 - ENGLISH
Settings
[BRIGHTNESS CONTROL]
The projector is equipped with a luminance sensor to 
measure brightness and functions to correct screen 
brightness resulting from changes in lamp brightness.
Use the projector when using multiple projectors to 
display on multiple screens to reduce changes in 
overall brightness of the multiple screens due to lamp 
degradation and suppress variation in brightness to 
preserve uniformity.
1) Press ▲▼ to select [BRIGHTNESS 
CONTROL].
2)...

[PROJECTOR SETUP] menu
ENGLISH - 103
Settings
10) Press ▲▼ to select [CALIBRATION 
TIME].
11) Press the  button.
12) Enter the time and press the  
button
▶z Measure brightness at a specified time. 
Dynamic iris is fixed to open during 
measurement.
13) Press 
▲▼ to select [CALIBRATION 
MESSAGE].
14) Press  ◀▶ to switch [CALIBRATION 
MESSAGE].
▶z The setting will change as follows each time 
you press the button.
[ON][OFF]
[ON] Displays a message during 
calibration.
[OFF] Does not display a message...

[PROJECTOR SETUP] menu
104 - ENGLISH
Settings
▶■To set [BRIGHTNESS CONTROL 
STATUS]
Displays the luminance control status.
4) Select [BRIGHTNESS CONTROL  
STATUS] in Step 3).
5)
 
Press the  button.
▶z The  [BRIGHTNESS CONTROL STATUS] 
screen is displayed.
▶z When [MODE] in [BRIGHTNESS 
CONTROL
 SETUP]  is [OFF]
Displays the luminance control disabled status.
0(185(7851
%5,*+71(66&21752/67$786
02( 352-(&725 2))
(1)
Displays the name of the projector in question.
▶zWhen [MODE] in [BRIGHTNESS 
CONTROL...

[PROJECTOR SETUP] menu
ENGLISH - 105
Settings
▶zError details
Error message
Remedy
[Exceed maximum 
number of projectors.]
 z Set no more than eight 
projectors in one group.
 zUse a computer and 
the dedicated “Multi 
Projector Monitoring & 
Control Software”
*1 to 
connect nine or more 
projectors.
[Please check the 
COMMAND CONTROL 
setting.]
 z Set the on-screen menu 
[NETWORK CONTROL] 
[COMMAND CONTROL] 
to [ON] for the projector 
in error

.
 z Set the [NETWORK 
CONTROL] [COMMAND 
POR

T] of all...

[PROJECTOR SETUP] menu
106 - ENGLISH
Settings
10) Set [BRIGHTNESS CONTROL GAIN] 
of all projectors to 100%.
11) Set [BRIGHTNESS CONTROL GAIN] 
of the darkest projector to 90%.
12) Adjust [BRIGHTNESS CONTROL 
GAIN] to match the [BRIGHTNESS 
CONTROL GAIN] set to 90% of the 
other projectors.
13) Set [MODE] in [BRIGHTNESS 
CONTROL SETUP] of all projectors to 
[AUTO], and [LINK] to [GROUP A].
14) Select [APPLY] in [BRIGHTNESS 
CONTROL SETUP] on all projectors 
and press the  button.
▶zLuminance control...

[PROJECTOR SETUP] menu
ENGLISH - 107
Settings
10) Press ◀▶ to switch [COMMAND].
▶z
The setting will change as follows each time 
you press the button.
[POWER ON][STANDBY][SHUTTER]*1
[P IN P]*1[LAMP 
SELECT]*1[INPUT]*1
*1: Displays the details set in Step  12) .
11) Press the  button.
▶zThe [COMMAND] detailed setting screen is 
displayed.
12) Press 
▲▼ to select a command.
▶z
For [SHUTTER], [INPUT], [LAMP  SELECT], 
and [P IN P], the setting will change as follows 
each time you press the button.
▶z...

[PROJECTOR SETUP] menu
108 - ENGLISH
Settings
[RS-232C]
Set the communication conditions of the / terminal.
1) Press ▲▼ to select [RS-232C].
2)  
Press the  button.
▶z The  [RS-232C]
 screen is displayed.
3) Press 
▲▼ to select an item.
▶■To set the communication 
condition of the  
terminal
4) Select [(IN) BAUDRA TE] in Step 3).
5)  
Press  ◀▶ to switch [(IN) BAUDRA

TE].
▶zThe setting will change as follows each time 
you press the button.
[9600][19200][38400]
6) Press 
▲▼ to select [(IN) P
ARITY].
7)...

[PROJECTOR SETUP] menu
ENGLISH - 109
Settings
[STATUS]
Displays the status of the projector.
1) Press ▲▼ to select [ST
ATUS].
2)  
Press the  button.
▶z The  [STATUS] screen is displayed.
3) Press 
◀▶ to switch the pages.
[INPUT] Displays the input terminal 
currently selected.
[SIGNAL NAME] Displays the input signal name.
[SIGNAL 
FREQUENCY] Displays the frequency of the 
input signal.
[PROJECTOR  RUNTIME] Displays the operation times of 
the projector.
[LAMP1] Displays the usage time and 
status of...

[PROJECTOR SETUP] menu
110 - ENGLISH
Settings
[NO SIGNAL SHUT-OFF]
You can set the power of the projector automatically 
to standby if there is no input signal by the specified 
time.
1) Press ▲▼ to select [NO SIGNAL
 
SHUT-OFF].
2)
 
Press  ◀▶ to switch [NO SIGNAL

 
SHUT-OFF].
[DISABLE] Disables the No signal shut-off 
function.
[10MIN.] -  [90MIN.] Allows you to set in ten minutes 
intervals.
[REMOTE2 MODE]
You can set the  terminal.
1) Press 
▲▼ to select [REMOTE2 MODE].
2)  
Press  ◀▶ to switch...