Panasonic DLP Based Projector PT-DZ8700U PT-DS8500U PT-DW8300U Operating Instructions

NETWORK menu
ENGLISH - 101
Settings
E-mail setup page 
J
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an \
e-mail message can 
be sent to one or more preset e-mail addresses (maximum two addresses)\
.
Click [Detailed set up], then [E-mail set up] to display the E-mail setu\
p page.
 
Select “Enable” to use the E-mail function.
 Enter the IP address or server name of the E-mail 
server (SMTP). The DNS server must be set if 
the server name is entered.
  Enter the...

NETWORK menu
102 - ENGLISH
Settings
 Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent 
at the times and on the days checked. 

NETWORK menu
ENGLISH - 103
Settings
E-mail setup page (continued) 
J
 
Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be 
used. Do not enter it when the second E-mail address is not going to be \
used.
 Select the conditions for sending E-mail to the second E-mail address.
MAIL CONTENTS: Select [NORMAL] or [SIMPLE].
ERROR: an error is detected by self-diagnosis.
LAMP1 RUNTIME: remaining lamp service time has reached the value set in the field.
LAMP2...

NETWORK menu
104 - ENGLISH
Settings
Authentication set up page 
J
The POP/SMTP server is set on this page when POP/SMTP authentication is required for mail transmissions.
Click [Detailed set up], then [Authentication set up] to display the Authentication server setup page.
 
Select the authentication method specified by 
your Internet service provider.
 Set this if SMTP authentication has been 
selected.
  POP server name field
  Available input characters:  
Alphanumeric characters (A - Z, a - z, 0 -...

NETWORK menu
ENGLISH - 105
Settings
Contents of mail sent 
J
Mail with the contents shown below is sent when the E-mail settings have\
 been  
Q
established.
ùùùÜ			*		/	+	*	%	Ü	,	.	+	&	!		0	+	.Ü	.	!	,	+	.	0äÿ		
						
åÜùùù
		.	+	&	!		0	+	.Ü		5	,	!ÜÜÜÜÜÜÜÜÜÜöÜ		ææææ
		!	.	%		(Ü	
	+ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜöÜ		íîïðñòó
éééééÜÜ	
é	)		%	(Ü	/	!	0	1	,Ü	 		0	Üééééé
		
				
	ý				
Ü	ý		
		
	Ü		
			Ü
				
	...

NETWORK menu
106 - ENGLISH
Settings
 
JAdjust clock page
Click [Detailed set up], then [Adjust clock] to display the Adjust clock page.
 
Time zone selection
 Button to update time zone setting
  Turn this [ON] to set the date and time 
automatically.
 When setting the date and time automatically, 
input the IP address or name of the NTP server.  
(When inputting the server name, the DNS server 
must be set.)
 New date field
 New time field
 Button to update time and date settings
Note
If the time...

ENGLISH - 107
Maintenance
Monitor Lamp indicators
Managing the indicated problems
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as 
follow.Attention
 
JLAMP1/LAMP2 indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Indicates the time 
for replacing the 
lamp unit. Did you notice a “REPLACE 
 
z
LAMP” message on the screen 
when turning on the projector 
power supply? This lamp monitor lights up when the 
 
z...

Monitor Lamp indicators
108 - ENGLISH
Maintenance
 
JTEMP indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Warm-up status
Did you turn on the power when 
 
z
the ambient temperature was 
lower than approx. 0 °C (32 °F)? Wait about 5 minutes in the current 
 
z
status.
Install the unit in a location having 
 
z
an ambient temperature from 0 °C 
(32 °F) - 45 °C (113 °F).
High temperature 
inside. (WARNING) Check the ventilation port is 
 
z
blocked.
Is the room air...

ENGLISH - 109
Maintenance
Replacement
Before replacing the unit
Turn off the POWER switch of the projector in proper way and disconnect the pow\
er plug from the wall outlet.  
z
(Æpages  38, 40)
Be sure to observe the procedure “Powering off the projector” 
 
z(Æpage  40) when performing power supply 
operation.
Replacing the unit
 
JACF (Auto Cleaning Filter) unit
ACF unit is an optional accessory.
You can check the remaining amount of the ACF unit in [REMAINING FILTER] of [STATUS] in PROJECTOR 
SETUP...

Replacement
110 - ENGLISH
Maintenance
 
JLamp unit
The LAMP unit is consumable product. You can check the duration of usage time using [LAMP1/LAMP2] of 
[STATUS] (
Æpage
 83) in the [PROJECTOR SETUP] menu.
Replacement of the lamp unit should be carried out by a qualified technician.
Contact the dealer to purchase a replacement lamp unit (ET-LAD310:1 bulb unit, ET-LAD310W: 2 bulb units).
 
JPrecautions on lamp unit replacement
Handle the lamp unit with special care as the lamp is made of glass. Dro\
pping...