Panasonic DLP Based Projector PT-DZ6710U PT-DZ6700U PT-DW6300U Operating Instructions

Precautions with regard to safety
ENGLISH - 11
Important 
Information
Make sure the following accessories are provided with your projector.
* The protectors for enclosed products, such as a plug cover or foam cartons, must be treated properly.
* Contact to an Authorized Service Center for lost accessories.
Accessories
Remote control (x1)
N2QAYB000371AA batteries for remote 
control (x2)Safety cable (x1), 
Washers (x2)
TTRA0214Power cord (x1)
K2CG3FZ00008
Projector lens cover (x1)
TKKL5244-1
CD-ROM (x1)...

ENGLISH - 12
Preparation
About Your Projector
Top, front and bottom view
Projector body
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20) of them as this may cause damage or injury.
• While the projector is not in use, keep the projector lens cover attached to protect the lens.
STANDBY(RED)/STANDBY(RED)/   ON(GREEN)   ON(GREEN)LAMPLAMPTEMPTEMPFILTERFILTER
STANDBY(RED)/STANDBY(RED)/   ON(GREEN)   ON(GREEN)LAMPLAMPTEMPTEMPFILTERFILTER
Indicators
Power indicator
Lamp1...

Preparation
About Your Projector
ENGLISH - 13
Side views
NOTE:
• Switch on the POWER button of the projector body that is located near the terminals before using the control buttons.
• Do not touch the LAN terminal with your bare hands or body, as body parts may have charged static electricity. Failure to do so may 
cause malfunctions. Do not touch the metallic parts of LAN terminal and cable.
• Please connect the LAN to indoor devices only.
Auto Cleaning Filter (ACF) compartment (page 32)
POWER button...

Preparation
About Your Projector
ENGLISH - 14
Remote control
POWER ON and POWER STANDBY 
buttons
POWER ON: Starts 
the projection while in 
the standby mode.
POWER STANDBY: Returns to the 
standby mode. (page 19)
INPUT SELECT buttons
These buttons 
select the RGB1, 
RGB2, DVI-D, 
VIDEO, S-VIDEO 
and SDI terminals. (page 22)
MENU buttons
Displays and clears the main 
menu, and returns to the 
previous menu when the menu 
is displayed. (page 27)
ON SCREEN button
Displays and clears the on 
screen...

Preparation
About Your Projector
ENGLISH - 15
Setting projector ID number to 
remote control
Each projector can be assigned a unique 2 digits ID 
number, and the remote control 2 digits ID number must 
be set to match the intended projector. The default 
setting of the projector ID is ALL. Set the ID of the 
projector in advance from the menu items.
1.Press the ID SET button.
Displays the projector ID number on the screen.
2.Within 5 seconds, enter the same number of the required 
projector by pressing...

Getting Started
ENGLISH - 16
Setting up
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,
Cautions when setting the projectors
When placing the projector in confined space, a ventilation or air conditioning system must be equipped, and keep enough 
ventilation space on the rear and both sides of the projector.
Projection method
Setting on a desk/floor and 
projecting from front Mounting on the ceiling and 
projecting from front...

Getting Started
Setting up
ENGLISH - 17
Removing the projection lens 
from the projector
1. Switch off the POWER button on the projector.
2. Rotate the lens cover counterclockwise and remove.
3. While pressing the lens release button, rotate the 
projection lens counterclockwise, and remove the 
projection lens.
Attaching the projection lens to 
the projector
1. Switch off the POWER button on the projector.
When the lens cover is attached, rotate counterclockwise 
and remove.
2. Align the guide of the...

Getting Started
Setting up
ENGLISH - 18
Connecting
1. Make sure the shape of the power plug and the AC IN 
terminal on the back of the projector match, then push 
the plug all the way in.
2. Align the side of the “power cord secure lock” with the 
side guide rail of the AC IN terminal of the projector and 
slide it in.
3. Place the latch to the latch catcher and press until it 
clicks.
4. Connect the power cord to a wall outlet.
Disconnecting
1. Unplug the power cord from the wall outlet.
2. Depress...

ENGLISH - 19
Basic Operation
Projecting
Switching on the projector
When using an optional lens, install a projection lens 
before switch on the projector.
1. Connect the supplied power cord (220 - 240 V AC, 
50 Hz/60 Hz) to the AC IN terminal.
2. Remove the projection lens cover from the lens.
3. Switch the POWER switch on that is on the side of the 
projector.
The power indicator lamp on the projector will flash in red. 
After a short period, the indicator will illuminate and the 
projector will enter...

Basic Operation
Projecting
ENGLISH - 20
Switching off the projector
1. Press the POWER STANDBY button.
The confirmation screen will be displayed.
2. Select OK and press the ENTER button, or press the 
POWER STANDBY button again.
The projection of the image stops, and the power indicator 
of the projector lights up orange. The cooling fan keeps 
running.
3. When the power indicator of the projector turns to red, 
switch the POWER switch to OFF.
When the power indicator of the projector turns to red,...