Panasonic DLP Based Projector PT-D3500U Operating Instructions
Here you can view all the pages of manual Panasonic DLP Based Projector PT-D3500U Operating Instructions. The Panasonic manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 51
![Page 51
51
E-mail setup page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be
sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail
set up] to display the E-mail setup page.
Select “Enable” to use
the E-mail function.Enter the IP address or server name of the E-mail server (SMTP).
The DNS server must be set if the server name is entered.
Enter the E-mail address of the
projector.
(maximum 63...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-50.png "Page 51
51
E-mail setup page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be
sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail
set up] to display the E-mail setup page.
Select “Enable” to use
the E-mail function.Enter the IP address or server name of the E-mail server (SMTP).
The DNS server must be set if the server name is entered.
Enter the E-mail address of the
projector.
(maximum 63...")
51 E-mail setup page With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail set up] to display the E-mail setup page. Select “Enable” to use the E-mail function.Enter the IP address or server name of the E-mail server (SMTP). The DNS server must be set if the server name is entered. Enter the E-mail address of the projector. (maximum 63...
Page 52
![Page 52
52
Using Web Browser Control
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
Enter the E-mail address to
which the E-mail is to be sent
when two E-mail addresses
are going to be used. Do not
enter it when the second E-
mail address is not going to
be used.
Select the conditions for sending E-mail.
ERROR:an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp service time has reached the value set in
the field.
INPUT AIR...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-51.png "Page 52
52
Using Web Browser Control
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
Enter the E-mail address to
which the E-mail is to be sent
when two E-mail addresses
are going to be used. Do not
enter it when the second E-
mail address is not going to
be used.
Select the conditions for sending E-mail.
ERROR:an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp service time has reached the value set in
the field.
INPUT AIR...")
52 Using Web Browser Control DNS server set up page Click [Network set up], then [DNS server set up] to display the DNS server set up page. Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be used. Do not enter it when the second E- mail address is not going to be used. Select the conditions for sending E-mail. ERROR:an error is detected by self-diagnosis. LAMP RUNTIME:remaining lamp service time has reached the value set in the field. INPUT AIR...
Page 53
![Page 53
53
POP server setup page
The POP server is set on this page when POP authentication is required for mail transmissions.
Click [Network set up], then [POP server set up] to display the POP server setup page.
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS
server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Select “Enable” for this setting
only when authentication is
required for sending mail.
POP...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-52.png "Page 53
53
POP server setup page
The POP server is set on this page when POP authentication is required for mail transmissions.
Click [Network set up], then [POP server set up] to display the POP server setup page.
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS
server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Select “Enable” for this setting
only when authentication is
required for sending mail.
POP...")
53 POP server setup page The POP server is set on this page when POP authentication is required for mail transmissions. Click [Network set up], then [POP server set up] to display the POP server setup page. Ping test page This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS server, etc. Click [Network set up], then [Ping test] to display the Ping test page. Select “Enable” for this setting only when authentication is required for sending mail. POP...
Page 54
![Page 54
54
Using Web Browser Control
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
settings have been established.
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• Mail with the contents shown below is sent
when an error has occurred.
Subject: Panasonic projector report(CONFIGURE)
=== Panasonic projector report(CONFIGURE) ===
Projector Type : D3500
–––––E-mail setup data –––––
TEMPERATURE WARNING SETUP
MINIMUM TIME...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-53.png "Page 54
54
Using Web Browser Control
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
settings have been established.
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• Mail with the contents shown below is sent
when an error has occurred.
Subject: Panasonic projector report(CONFIGURE)
=== Panasonic projector report(CONFIGURE) ===
Projector Type : D3500
–––––E-mail setup data –––––
TEMPERATURE WARNING SETUP
MINIMUM TIME...")
54 Using Web Browser Control Contents of mail sent • Mail with the contents shown below is sent when the E-mail settings have been established. Adjust clock page Click [Network set up], then [Adjust clock] to display the Adjust clock page. • Mail with the contents shown below is sent when an error has occurred. Subject: Panasonic projector report(CONFIGURE) === Panasonic projector report(CONFIGURE) === Projector Type : D3500 –––––E-mail setup data ––––– TEMPERATURE WARNING SETUP MINIMUM TIME...
Page 55
![Page 55
55
Network config page
Set this to ON to enable the
DHCP client function.
Enter the IP address if DHCP
server is not used.
Enter the net mask if DHCP
server is not used.
Enter the gateway address if
DHCP server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance.
Network status page
Click [Network Setting], then [Network status] to display the Network status page.
Network software version
display
Set IP...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-54.png "Page 55
55
Network config page
Set this to ON to enable the
DHCP client function.
Enter the IP address if DHCP
server is not used.
Enter the net mask if DHCP
server is not used.
Enter the gateway address if
DHCP server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance.
Network status page
Click [Network Setting], then [Network status] to display the Network status page.
Network software version
display
Set IP...")
55 Network config page Set this to ON to enable the DHCP client function. Enter the IP address if DHCP server is not used. Enter the net mask if DHCP server is not used. Enter the gateway address if DHCP server is not used. Enter the name of the projector here. Enter the host name here if it is required when the DHCP server is going to be used, for instance. Network status page Click [Network Setting], then [Network status] to display the Network status page. Network software version display Set IP...
Page 56
56 Using the PJLink™protocol The network functions of the projector are compatible with PJLink™Class 1. The operations mentioned below can be performed from a personal computer using the PJLink™protocol. • Projector settings • Projector status inquiry Supported commands The commands for controlling the projector using the PJLink™protocol are as given in the table below. PJLink™security authentication The password used in PJLink™is the same as the password set in the Web Browser Control. To use PJLink™...
Page 57
57 Before asking for service---Before asking for service, check the following points. SymptomsChecks • Is the power cord plug correctly plugged in? • Is the MAIN POWER turned on? • Is electricity running to the power outlet? • Is the temperature monitor (TEMP) indicator on the front of the unit flashing or turned on? (See page 42) • Is the lamp monitor (LAMP) indicator on the front of the unit flashing or turned on? (See page 42) • Is the lamp unit door installed correctly? • A wrong ID is set. (See...
Page 58
58 Specifications 1Value when accessory lens is used, “PICTURE MODE” is set at “DYNAMIC” and zoom lens is in the wide lens position. 2HDCP (High-bandwidth Digital Content Protection) HDCP is a digital video signal encryption system developed with the aim of protecting digital content. Power supplyAC 120 V, 50 Hz/60 Hz Power consumption400 W (about 10 W in standby without fan running) DLPTMpanel Panel size Display system Number of pixels 0.7 inch (aspect ratio 4:3) DMDTMelement, DLP type 786 432 pixels (1...
Page 59
![Page 59
59
Interface ports
RGB2 input terminal
Video input terminal
S-video input terminal
Serial input terminal
Remote1 input terminal
Remote2 terminal
DVI-D terminal
LAN terminal
Audio input terminal
Audio output terminal
1 set of high-density, D-sub 15p (female)
[For YP
BPRinput]
Y: 1.0 V [p-p] synchronization signal included, P
BPR: 0.7 V[p-p] 75 Ω
[For RGB input] 0.7 V[p-p] 75 ΩFor G-SYNC: 1.0 V[p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity
automatically adjusted
VD:
TTL,...](http://img.usermanuals.tech/thumb/58/75949/w300_pt-d3500u_en_om_d-58.png "Page 59
59
Interface ports
RGB2 input terminal
Video input terminal
S-video input terminal
Serial input terminal
Remote1 input terminal
Remote2 terminal
DVI-D terminal
LAN terminal
Audio input terminal
Audio output terminal
1 set of high-density, D-sub 15p (female)
[For YP
BPRinput]
Y: 1.0 V [p-p] synchronization signal included, P
BPR: 0.7 V[p-p] 75 Ω
[For RGB input] 0.7 V[p-p] 75 ΩFor G-SYNC: 1.0 V[p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity
automatically adjusted
VD:
TTL,...")
59 Interface ports RGB2 input terminal Video input terminal S-video input terminal Serial input terminal Remote1 input terminal Remote2 terminal DVI-D terminal LAN terminal Audio input terminal Audio output terminal 1 set of high-density, D-sub 15p (female) [For YP BPRinput] Y: 1.0 V [p-p] synchronization signal included, P BPR: 0.7 V[p-p] 75 Ω [For RGB input] 0.7 V[p-p] 75 ΩFor G-SYNC: 1.0 V[p-p] 75 Ω HD/SYNC: TTL, high-impedance, positive/negative polarity automatically adjusted VD: TTL,...
Page 60
60 Compatible Signal List NTSC/NTSC4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 480i 576i 480p 576p 1080/60i 1080/50i 720/60p VGA400 VGA480 SVGA MAC16 XGA MXGA MAC21 MSXGA SXGA UXGA720 720 720 720 720 720 1 920 1 920 1 280 640 640 640 640 640 640 640 800 800 800 800 800 832 1 024 1 024 1 024 1 024 1 024 1 152 1 152 1 152 1 152 1 280 1 280 1 280 1 280 1 400 1 600X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X480i 576i 480i 576i 483 576 1 080i 1 080i 720 400...