Panasonic Digital Video Cassette Recorder AG DV2000P Operating Instructions

To insert a new program between existing programs:
1  Select  Insert a program,  and then press OK.
The program list is displayed.
2 Select the program number where a program is to be
inserted, and then press  OK.
The Insert a program screen is displayed.
3  Refer to the pages that describe the Program Editing
functions (on pages 48-59), and set the new program.
4  When setting is complete, press  OK.
5  Press  EDIT MENU.
To cancel a program:
1  Select  Erase a program,  and then press OK.
The program...

Edit Timing Adjustment
When performing editing in conjunction with a unit which has a different mechanism, there may be a lag in the edit start\
 point due
to a deviation between the time a pause cancellation signal is received by the recording unit and the time recording act\
ually
begins.
Edit Timing Adjustment is used to compensate the edit start and end time in light of this start-up time deviation.
Program Editing
After setting edit start/end points, the actual editing
operation may start slightly...

Select Timing Adjust, and then press
OK.
Adjust the timing for the edit start point
by setting the amount of the
discrepancy for the
start-up time.
The setting is displayed in
frames (apporoximately 1/30 of a second) units.
Pressif the start point is too early;
pressif it is too late.
Each time the button is pressed, the tape moves
by 1 frame.
Corrections can be made in the range of ±30
frames.
Press OK.
Adjust the timing for the edit end pont
in same way.
Press 
OK.
Select Start Insert (Assemble or...

Edit Timing Adjustment (continued)
Manual Editing
If there is a deviation in the results of a manual editing
operation, the timing of the edit start (In) position on the
playback unit can be adjusted by approximately ±1 second.Perform the procedure described below when setting an edit
start point in any editing mode.
Example: Manual Copying
Operations
Select  Timing Adjust,  and then press
OK.
Adjust the timing for the edit start point
by setting the amount of the
discrepancy for the start-up time.
The...

Glossary of Terms
Assemble
With the Assemble function, only the required portions of
the original (source) tape are copied to another tape and
linked together.
Audio Dubbing
You can record two audio tracks (Stereo 1 and Stereo 2) on
a tape that is recorded in 12bit audio mode. (When the tape
is first recorded, the audio is recorded only in the Stereo 1
track.) The Audio Dubbing function allows you to add new,
separate audio in the Stereo 2 track.
Audio Mixing
You can record two audio tracks (Stereo 1 and...

DV Terminal 

On Screen Display Messages
Before requesting service, check the following points once
again.
The error message is indicated in brackets [ ] .
[Please insert video tape.]
REC, (PLAY),
(FF),(REW) or JOG/
SHUTTLE is pressed when no cassette is in the VCR.
Insert a video cassette.
[Recording not allowed. Check setting of the record-
prevention tab.]
REC, VIDEO INSERT, AUDIO INSERT or AUDIO
DUB has been pressed when using a cassette with
the opened record-prevention tab. Use a cassette
with a closed...

Before Requesting Service
Before requesting service, check the following points once
again.
Self Test IndicationRecording does not operate correctly
This VCR has a self-diagnosis and display function. If the
VCR detects trouble during installation or during use, the
following indications automatically appear in the VCR
display. Indications are displayed in the form of a single
English letter plus two numbers such as [H01].The symptom description is indicated in quotations “”.
indication flashes whenever...

Editing  does not operate correctly
The symptom description is indicated in quotations “”.
“One-Touch-Editing does not work.”
Is One-Touch-Edit on the SET UP screen set to“ON” ?
“Editing does not commence; the VCR stays in the
recording pause state.”
While setting the edit start point on the playback unit,
this VCR switched from the recording pause state to
the stopped state.
In order to protect the tape and the head from
damage, this VCR is designed to automatically stop if
it is left in the recording...

Flow Chart for On Screen Displays
SET UP On Screen Display
70