Panasonic Digital Disk Recorders Wj Hd500a Operating Instructions

84


(camera 1 to 5 are assigned to a group)
3. To display a Single Spot image, select an image to be
displayed on the monitor by pressing one of the numer-
ic buttons that the indicator in the button lights up.
Multi Sequence (Live)
A series of camera images can be displayed in succession
on the monitor screen for the specified duration.
Each sequence step can be combined with four screen
segments (quad) and single image.
Refer to the 5 - 1 - 1 MULTI LIVE SEQUENCE SETUP for fur-
ther details.
1. Select...

85
Group Multi Sequence
The assigned group camera images can be displayed in
succession on the monitor screen for the specified dura-
tion.
Each sequence step can be displayed as either four screen
segments (quad) or a minimum quantity of the segment
screen, depending on the setting.
Refer to GROUP SEQ MODE in the 5 - 1 SEQUENCE
SETUP for further details.
1. Select one of the group displays by pressing the
GROUP SELECTbutton.
Pressing this button toggles the group display on the
monitor as shown below....

86
The alarm function activates the warning alarm status, when
an externally connected alarm sensor is turned on, or an
installed Video Motion Detector (optional) is activated.
The Disk Recorder activates the recording alarm status
within the specified recording mode; it also activates the
status display, such as the ALARM indicator, monitor dis-
play and alarm buzzer, to indicate that an alarm signal has
been received.
Described below is an example of an alarm status activa-
tion.
For further details...

87
Alarm Suspension
This function disables the activation of the alarm link and
instead enables storing of any alarm activated in the
ERROR REPORT table.
It is used to suspend the alarm link during the Disk
Recorder’s setup.
To suspend the alarm:
1. Press the ALARM RESETand REC PREVIEWbuttons
at the same time.
The ALARM SUSPEND indicator lights to indicate that
this function is selected.
2. Press the ALARM RESETbutton to reset the alarm sus-
pension.
The ALARM SUSPEND indicator goes off.
Alarm Reset...

88
Internal Timer Recording
The internal timer recording begins when the reserved start
time comes, and continues until the reserved end time is
reached.
The reservations are made in the TIMER REC SETUP menu,
and the TIMER parameter is set to INT in the WJ-HD500
SETUP menu.
As described before, the received video inputs can be
assigned to four groups, and those groups are assigned to
the programmed timer.
It enables the use of different recording modes for each
group (Time Lapse, Multi Shot or One...

89
Alarm Recording
The Disk Recorder activates the recording alarm status within the specified recording mode, when an externally connected
alarm sensor is turned on, or when the installed Video Motion Detector (optional) is activated.
The alarm recording mode is determined by the setup in the WJ-HD500 SETUP menu. Described below is an alarm recording
mode for each recording mentioned above.
Note:The received alarm is ignored when the Disk Recorder is recording images in the Emergency Recording. (the...

90
• Set to ALM-PRI
Records the alarm-activated input images preferentially over other video inputs.
• Set to ALM-ONLY
Records the particular images that have activated the alarm. • Set to ALM-MULTI
• Records alarm images and creates thumbnails of images that have most recently received an alarm.
• Records alarm images that is chosen detecting the rest of alarm duration every alarm inputs. 
• Records alarm images according to the REC RATE(BASE) in evenly until reaches REC RATE(MAX). Then the
sum exceeds...

91
HDD
Emergency Recorder
Manual Recorder
Emergency Recorder
Group 1
Timer
RecorderGroup 2
Group 3
Group 4
Emergency Recording
The Emergency Recording is given priority over any other recording modes.
This recording is controlled through input from the CONTROL port on the rear of the Disk Recorder.
It records all camera images in Time Lapse Recording mode with the specified recording rate, quality and duration.
Refer to EMERGENCY REC SETUP menu for further details.• Set to ALM-MULTI
• Records alarm...

92
The recorded images on the disk can be played back on
the Multiscreen Monitor.
The procedures described below are for operations playing
back the hard disk.
Refer to the PLAYBACK MODE or THUMBNAIL parameter
in the COMMON SETUP menu for the play back setup.
Basic Playback
1. Select the group to be played back by pressing the
GROUP SELECTbutton.
Note:Ensure to select one of groups for playing back
when the recording was made in internal timer
recording that is recorded images with a group unit.
2....

93
Search Record Function
The Disk Recorder has two search functions.
The procedures below describe how to search and play
back records.
1. Select the group to be played back by pressing the
GROUP SELECTbutton.
2. Pressing the ALARM SEARCHbutton toggles the indi-
cator in the button on and off.
Selecting either mode will display the list as shown
below.
On:Displays only the Alarm (REC+ALM) and
Emergency Record List of the selected group.
Off:Displays all Record Lists for the selected group.
3. Press the...