Panasonic Digital Disk Recorder Wj Rt208 Operating Instructions

31
(4) After completing the settings, press the [MENU] button
again to close the camera setup menu.
Caution:When displaying the Special Menu, move the
cursor to SPECIAL on the camera setup menu and
press the camera selection button [2].
When returning the camera settings to the default
settings, move the cursor to CAMERA RESET and
press the camera selection button [3].
Press the [ESC] button to move from the Special
menu back to the previous menu.
2.6 Control this Unit with a PC
When this unit is...

32
3. Setup
Setup Menu List
Setting Item
SYSTEM MANAGEMENT
SYSTEM SETUP
DISK INFORMATION
REBOOT SYSTEM
PICTURE ADJUST
TIME & DATE
VERSION
SEARCH
Description
Basic operation settings of this unit
HDD information and initialization
Restart of this unit
Screen adjustment of each channel
Time and date setting
Version confirmation of the software
Recording data check and playback
Timer recording settings of each channel
REC & EVENT SETUP
TIMER REC
TERMINAL REC Terminal recording settings of each channel
VMD...

33
3.1 Operation for Various Settings
3.1.1 System Management (SYSTEM MAN-
AGEMENT)
(1) Press the [MENU] button. WJ-RT208 SETUP MENU
appears.
(2) Move the cursor to SYSTEM MANAGEMENT and
press the [SET] button.
(3) Move the cursor to SYSTEM SETUP and press the
[SET] button.
   WJ-RT208 SETUP MENU
SYSTEM MANAGEMENT
SEARCH
REC&EVENT SETUP
PTZ SETUP
CAMERA SETUP
COMMUNICATION SETUP
REPORT
USER INFORMATION
DATA MANAGEMENT
    SYSTEM MANAGEMENT
SYSTEM SETUP 
DISK INFORMATION 
REBOOT SYSTEM 
PICTURE ADJUST...

Descriptions and remarksSelectable parameters
[Default Setting]Item
Full, 1/2F, 1/4F, 1/8F, 1/16F
Full
Note:When Terminal Input is set at N.C., an alarm unit of N.O. should be connected to the alarm port of this unit. If no con-
nections are made, the alarm port will be N.O. (normally open) and will continue receiving alarm signals at all times. Pre Recording
Rec. Quality
I Frame Inter.
Resolution
Alarm Spot
Stream Type
Terminal Input
Frame RateThe time period for pre recording can differ according to...

35
Disk information (DISK INFORMATION)
In regard to hard disc initialization and hard disc index
recovery, refer to 3.4 herein.  
Reboot system (REBOOT SYSTEM)
(1) Press the [MENU] button. WJ-RT208 SETUP MENU
appears. Move the cursor to SYSTEM MANAGEMENT
and press the [SET] button. (Refer to steps (1) and (2)
in 3.1.1.)
(2) Move the cursor to REBOOT SYSTEM and press the
[SET] button.
(3) The confirmation dialog box will be displayed.
(4) Move the cursor to [OK] and press the [SET] button. 
Picture...

36
Stream type:CBR or VBR
Default: CBR (If screen changes seem extreme,
the setting made at VBR is preferable.)
Recording date:SUN, MON, TUE, WED, THU,
FRI, SAT, DAILY
Two types of Period1 and/or Period2 can be set
up for one day. 
If the same setting is used every day, the setting
should be made with DAILY. When all time spans
have been set up, select On.
Default: 00:00 - 24:00, Off
(4) If the same setting is required for all channels, press
[All] after completing the setting for one channel. All the...

37
Video motion detector recording (VMD REC)
(1) Press the [MENU] button. WJ-RT208 SETUP MENU
appears. Move the cursor to REC&EVENT SETUP and
press the [SET] button. (Refer to steps (1) and (2) in
3.1.3.)
(2) Move the cursor to VMD REC and press the [SET] but-
ton.
Camera ID:1-8
Default: 1
Sensitivity:01 - 99 (01 corresponds to the maximum
sensitivity.) 
Default: 10
Area setup:140 grid areas can be established inde-
pendently. 
Default: All areas are not selected.
Alarm output connector:0-3
Default: 0 (0...

38
2. While NetBackup (data backup function) is being per-
formed using the provided software, VMD response
may be delayed.
Record length (RECORD LENGTH)
(1) Press the [MENU] button. WJ-RT208 SETUP MENU
appears. Move the cursor to REC & EVENT SETUP
and press the [SET] button. (Refer to steps (1) and (2)
in 3.1.3.)
(2) Move the cursor to RECORD LENGTH and press the
[SET] button.
Setup enabled range:005 - 240
Default: 15
Note:If the RECORD LENGTH setup conditions are
changed in the middle of recording,...

39
(2) Move the cursor to AUDIO SELECT and press the
[SET] button.
(3) Use the direction button (up/down) and move the cur-
sor to the setting channel. The radio button is lit up and
recording takes place when the audio signals are sent.
Note:Even though recording is performed within the
same time period, much more hard disk capacity is
needed for recording with audio signals than
recording without audio signals.
3.1.4 PTZ setup (PTZ SETUP)
PTZ selection (PTZ SELECT)
For the selection of the camera,...

40
Channel Name:Indicates the correlation between the
camera title and serial number. Channel name can
be changed using the provided software.
Cautions:For the [All] operation and functions, refer to the
timer recording explanation.
Notes:
1. CH Enable of channel 1 cannot be set at Off. During
playback in channel 1, it is impossible to set up its
masking area.
Mask Enable:
On:Used to enable masking area setup. The masked
area will not be displayed and recorded (Black
screen will be recorded.).
Off:The...