Panasonic Digital Disk Recorder Wj Rt208 Operating Instructions

21
■DIP Switch Setting
When this unit is connected to any other system unit, it is necessary to set up the 2-bit DIP termination switches located on the
back of this unit.
DIP termination switches:
The dip switch positions are defined by the attribute of the unit connected to the system’s DATA terminal.
*Refer to the label in regard to setting the DIP termination switches on the rear panel.
Caution:Switch 2 of the DIP termination switch is not available.
12
Machine connected to the DATA port...

22
Setup Procedures
1. Preparation
1.1 Turning the Power On
(1) Connect the AC power cord to the AC power connector
on the rear panel.
(2) Turn on the power switch on the rear panel.
A hard disk detection screen appears on the monitor for
a few seconds.
After that, a live monitoring screen of the camera is dis-
played.
1.2 User Registration
(1) When any button other than the camera selection but-
ton and the screen split button is pressed while the key-
board is locked (in the state of no log-in), a...

23
1.3 Basic Operation of the Menu
Understand the free type structure of the menu before you open this menu.
B
CD
EG
H
FI
qw q
w
   WJ-RT208 SETUP MENU
SYSTEM MANAGEMENT
SEARCH
REC&EVENT SETUP
PTZ SETUP
CAMERA SETUP
COMMUNICATION SETUP
REPORT
USER INFORMATION
DATA MANAGEMENT A
B
C
D
E
F
G
H
I    SYSTEM MANAGEMENT
SYSTEM SETUP 
DISK INFORMATION 
REBOOT SYSTEM 
PICTURE ADJUST 
TIME & DATE 
VERSION 
       REC & EVENT
TIMER REC
TERMINAL REC
VMD REC
RECORD LENGTH
AUDIO SELECT        PTZ SETUP
PTZ SELECT...

Menu type
1. Main menu
Direction button (up or down): Used to move the cursor up or down.
[SET] button: Used to move the cursor to the next submenu or the setup dialog box.
[ESC] button: Used to close the setup menu, and returns the screen to the live monitoring images.
2. Sub menu
Direction button (up or down): Used to move the cursor up or down.
[SET] button: Used to move the cursor to the setup dialog box.
[ESC] button: Used to return the screen to the main menu.
3. Dialog
Direction button (up or...

25
Note:If time is corrected in the middle of recording,
part of the recorded data may fail to be played. This
is because some turbulence can arise in the record
start time and the end time.
1.5 Turning the Power Off
The power supply for this unit cannot be turned off if hard
disk data are being played or data are being recorded on
the hard disk. Operation for playback or recording has to
be stopped first. Turn off the power supply after confirming
that the HDD indicator of the front panel is not lit....

26
2. Operation
2.1 Screen Operation
2.1.1 Spot display
If you want to display only one screen of a specified chan-
nel, press the channel number. 
Images from the selected camera channel will be displayed
with a spot display.
Note:In the case of a 6-split screen, the screen of the
selected channel is displayed in the top left area (the
largest area of the 6-split areas). No display is present-
ed on the spot screen. 
If you want to have a display on the spot screen,
changeover to the multi screen...

27
The playback is stopped, and live monitoring images
are displayed on the channel 1 screen.
The playback icon also disappears.
Note:If you keep pressing the [STOP] button for 2 sec-
onds or more when you want to stop playback of
channel 1, recording of channel 1 is also stopped.
2.3.2 Playback the record
(1) FWD/REV playback
Press the [FWD] button, [REV] button, or direction but-
ton (left/right) during playback.
Each time one of these buttons is pressed, the
FWD/REV speed is changed. 
The playback...

3. Even though an alarm occurs, no automatic recording
is carried out unless Period1 or Period2 of TERMI-
NAL REC and VMD REC has been set at On.
4. Information about external alarms is directly sent to the
PC through the network. It has no relation to the TER-
MINAL REC and VMD REC setting at the recorder.
Please refer to 
on the CD-ROM. 
5. When Full is selected for Frame Rate, performing
playback, recording of all channels and transmission of
all channels of Net Client in parallel for many hours may...

29
(3) Move the cursor to PTZ SELECT and press the [SET]
button.
Move the cursor to the desired channel by using the
direction buttons (up/down). Select the channel by
using the direction buttons (right/left).
In the above figure, Cam1 is selected in the PTZ
SELECT menu. No other camera are selected in other
channels.
(4) Press the [MENU] button. WJ-RT208 SETUP MENU
appears. Refer to step (1).
(5) Move the cursor to CAMERA SETUP and press the
[SET] button. 
The CAMERA SETUP menu appears. Select PTZ...

30
2.5.3 Zoom
(1) Select the zoom/focus mode by pressing the [SET] but-
ton twice.
The zoom/focus icon  is displayed on the screen of
the selected channel.
(2) Press the direction button (up or down) to control the
camera’s zoom. 
(3) Press the [SET] button twice. The zoom/focus mode is
cancelled.
2.5.4 Focus
(1) Select the zoom/focus mode by pressing the [SET] but-
ton twice.
The zoom/focus icon  is displayed on the screen of
the selected channel.
(2) Adjust the focus by pressing direction buttons...