Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Operating Instructions

							61
Step 5
After checking the size of the data to be copied and 
the remaining capacity, press the [SET] button after 
moving the cursor onto the [Copy] button. 
  →  The copy data list window will close. Copying will 
start	and	the	[COPY]	icon	will	be	displayed	on	the	
task bar on monitor 2. When copying is complete, 
the	[COPY]	icon	will	disappear.	
Important:
	 •	 Do	not	remove	the	SDHC/SD	memory	card	during	 copying data onto the SDHC/SD memory card. It 
may damage data on the SDHC/SD memory card.
	 •	 In	the	following	cases,	copying	will	not	start	even	 when the [SET] button is pressed after moving the 
cursor onto the [Copy] button. 
	 •	 When	the	end	time	is	set	earlier	than	the	start	 time
	 •	 Copying	will	be	performed	even	when	the	remain- ing capacity of the destination media is not 
enough for copying. 
	 •	 When	pressing	the	[COPY]	button	on	the	front	 panel during copying, the confirmation window for 
cancellation of the current copying will be dis-
played. It is possible to cancel the current copying 
on this window. Copying continues even during 
the confirmation window is being displayed. When 
the power of the recorder is turned off during 
copying, the media used for copying may become 
unusable.
Step 6
When copying on a DVD, it is necessary to complete 
copying by removing the DVD. (When copying on an 
SDHC/SD memory card, it is unnecessary to take the 
following procedures to complete copying.) 
When the [Copy] button on the front panel is pressed, 
the "Eject media" menu will be displayed. Select 
"Eject media", and then press the [SET] button.
 →  The copy completion process will start. When the 
copy completion process ended, the completion 
notification window will be displayed and the DVD 
will become ready to remove.
    
Note:
	 •	 It	is	impossible	to	play	copied	data	if	the	copied	 data is finalized by the copy completion process 
even when copying onto a DVD is complete.
	 •	 It	is	also	possible	to	remove	the	DVD	in	the	follow- ing procedures.
	 •	 Move	the	cursor	onto	the	[Search	&	Copy]	but- ton of the submenu.
  → The menu list will be displayed. 
	 •	 Move	the	cursor	onto	"Eject	media"	on	the	 displayed menu list, and then press the [SET] 
button. 
 
Step 7
The DVD can be removed when the tray lock is 
released by pressing the button at the center of the 
DVD drive. 
Important:
	 •	 Once	a	DVD	is	used	for	copying	and	removed	 from the recorder, it is impossible to copy another 
data on it.
Note:
	 •	 The	tray	will	not	come	out	even	when	the	eject	 button is pressed if the operation described in 
step 6 is not performed to complete copying.
 
481216
15913261014371115
Eject button 
						

							62
Operation and configuration when connecting 
the recorders in cascading connection
When connecting the recorders (up to 5 recorders) in cascading connection, all images managed by the con-
nected recorders can be monitored on a single monitor. 
The following are descriptions of how to operate when the recorders are connected in cascading connection. To 
operate the recorders connected in cascading connection, it is necessary to configure the settings in advance. 
Refer to the Installation Guide for further information.Important:
	 •	 Audio	cables	can	also	be	connected	in	cascading	connection.	
 
Configuration
Configure the settings required for cascading connection. Operations and settings of the WJ-HD716K ar\
e the 
same as that of the WJ-HD616K.
For WJ-HD616K
Select "On" for "Cascade" on the "Cascade" tab under "Display" of the se\
tup menu of the recorder to be con-
nected in cascading connection. Set the unit addresses of recorders as follows. 
WJ-HD616K Unit address (system) Unit address (controller)
First recorder 001
Select a number except 001 - 004 and not used 
for the other devices.
Second recorder 002
Third recorder 003
Fourth recorder 004
Fifth recorder 005
Settings of a system controller
Set the unit addresses of system controllers as follows. 
System controller
Unit address Remarks
First system controller 001It is possible to operate all monitor 1 and monitor 
2 connected to the first through fifth WJ-HD616K.
Second system controller 002 Monitor 1 and monitor 2 connected to the first 
through the fifth WJ-HD616K are available to oper-
ate. However, camera selection on monitor 2 is 
unavailable. 
Third system controller
003
Fourth system controller 004
     
						

							63
Example of video output (analog) connection
    
Operation using the buttons on the front panel
It is possible to operate using the buttons on the front panel. When selecting monitor 2, images will be dis-
played on monitor 2 connected to the first WJ-HD616K. When selecting mon\
itor 1, images will be displayed on 
monitor 1 connected to the WJ-HD616K currently being operated. 
Only the WJ-HD616K currently being operated is subject to operation. It is impossible to operat\
e the other 
WJ-HD616K using the buttons on another WJ-HD616K. 
Operate using the system controller
	 •	 When	using	the	system	controller	whose	unit	address	is	001
   It is possible to operate all the WJ-HD616K/WJ-HD716K in cascading conne\
ction by designating the unit 
number from a PS·Data compatible system controller. 
    Refer to the operating instructions of the system controller for how to control it in the PS·Data mode. 
	 •	 When	using	the	system	controller	whose	unit	address	is	002	-	004	
    It is possible to operate all the WJ-HD616K/WJ-HD716K using the PS·Da\
ta compatible system controller. 
However, camera selection on monitor 2 is unavailable. 
Monitor 2
Monitor 1
Monitor 1
Monitor 1
Monitor 1 PS·Data compatible 
system controller
(Unit address: 002)
Unit address (system): 001
First recorder
Unit address (system): 002
Second recorder
Unit address (system): 003
Third recorder
Unit address (system): 004
Fourth recorder
* Do not assign unit address numbers (controller) 001 - 004 and also numbers used for the other devices to each th\
e WJ-HD616K. 
(Unit address: 003)
(Unit address: 00)
4321876512110/10916151413
MOUSEDigital Disc Recorder WJ-HD616
4321876512110/10916151413
MOUSEDigital Disc Recorder WJ-HD616
4321876512110/10916151413
MOUSEDigital Disc Recorder WJ-HD616
4321876512110/10916151413
MOUSEDigital Disc Recorder WJ-HD616
(Unit address: 001) 
						

							64
Operate the camera
Step 1
Press the [SUB MENU] button on the front panel. 
  →  The submenu window will be displayed. 
Step 2
Move the cursor onto the [Camera control] button of 
the submenu, and then press the [SET] button.
  →  The menu list will be displayed. Move the cursor 
onto "Camera operation" on the displayed menu 
list, and then press the [SET] button. 
      
→  The [Pan/Tilt] tab of the camera control panel will 
be displayed. 
    
It is possible to operate the following camera operations when displayin\
g live images from a camera with the 
panning/tilting and zooming function. 
	 •	 Panning/Tilting	 Adjust	the	horizontal/vertical	position	of	images	from	the	camera
	 •	 Zoom	 Zoom	in/out	images	from	the	camera	
	 •	 Focus	 Adjust	the	focus	of	the	camera
	 •	 Iris	 Adjust	the	lens	iris	of	the	camera
	 •	 Preset	position	function		 	 Register	preset	positions	and	move	the	camera	direction	to	the	registered	pre-
set positio.
	 •	 Auto	function		 Activate	the	auto	function	of	the	camera	according	to	the	settings	of	the	camera	
Note:
	 •	 The	camera	operation	can	be	performed	only	when	displaying	images	on	a	1-screen	on	monitor	1.	
	 •	 Depending	on	the	model	of	the	camera,	some	operations	may	not	work.	
	 •	 When	a	user	with	a	higher	user	priority	is	operating	at	the	same	time,	it	may	
be	impossible	to	operate	the	
camera.	In	this	case,	the	indication	"BUSY"	will	be	displayed	on	the	operation	panel.	Refer	to	the	Installation	
Guide for further information about the priority.
	 •	 Refer	to	page	70	for	how	to	display	the	setup	page	of	the	camera	and	configure	the	settings	of	the	camera.	
 
Display the camera control panel
The panning/tilting, zooming, focus adjustment and iris adjustment can b\
e made on the camera control panel. 
     
						

							65
Step 1
Display the camera control panel. (☞ Page 64)
    Step 2
Adjust the horizontal/vertical position of images from 
the camera using the arrows button (C, D, A, B). 
The camera direction will move to the direction com-
manded by the arrows button. 
Note:
	 •	 It	is	possible	to	make	the	panning/tilting	speed	 slower by adjusting the camera direction when the 
[HOLD] button is being lit (by pressing the [HOLD] 
button). 
	 •	 To	release	the	hold,	press	the	[HOLD]	button	 again. 
 
    
Panning/Tilting
Adjust the horizontal/vertical position of images from the camera. 
    
Zooming 
Zoom in/out images from the camera. Depending on the models of the connected cameras, the available zoom-
ing factors may be different.
Refer to the operating instructions of the camera for further informatio\
n.
    
Step 1
Display the camera control panel (☞ page 64), and 
then press the camera selection button [2] on the 
front panel. 
 →  The [Zoom] tab will be displayed. 
    Step 2
Press the arrows button (C D). When pressing C, 
the displayed image will be zoomed out. When press-
ing D, the displayed image will be zoomed in. 
     
						

							66
Step 1
Display the camera control panel (☞ page 64), and 
then press the camera selection button [2] on the 
front panel. 
  →  The [Focus] tab will be displayed. 
    Step 2
Press the arrows button (A B). When pressing A, 
the focal point will move to the near side. When 
pressing A, the focal point will move to the far side. It 
is possible to automatically adjust the focus by press-
ing the [SET] button on the front panel. 
    
Focus adjustment
Adjust the focus of the camera. The auto focus function is available.
    
Iris adjustment
Adjust the lens iris of the camera
    
Step 1
Display the camera control panel (☞ page 64), and 
then press the camera selection button [3] on the 
front panel. 
  →  The [Iris] tab will be displayed. 
    Step 2
Press the arrows button (A B). When pressing A, 
the iris will be closed and images will become darker. 
When pressing B, the iris will open and images will 
become brighter. It is possible to reset the adjusted 
iris to the default by pressing the arrows button (D). 
     
						

							67
Step 1
Move the camera direction to a position to be regis-
tered as a preset position. 
Step 2
Display the [Pan/Tilt] tab of the camera control panel 
(☞ page 65)
Step 3
Press the [SET] button on the front panel. 
  →  The "Preset/Auto" window will be displayed. 
    Step 4
Enter a preset position number to be registered. 
To enter the preset position number, press the camera 
selection button (1 - 0/10) or rotate the jog dial 
(inside). 
Step 5
Move the cursor onto the [Regist] button, and then 
press the [SET] button. 
  →  The confirmation window will be displayed. When 
the [OK] button on the confirmation window is 
selected, the "Preset/Auto" window will close and 
the camera direction checked by the images cur-
rently being displayed will be registered as a pre-
set position. 
    
Preset position function
Move the camera to the preset position registered in advance. It is necessary in advance to register preset posi-
tions to perform the preset position function. 
Registration of preset positions 
Register the preset positions for the camera. Up to 256 preset positions can be registered. The maximum num-
ber of preset position registration varies depending on the model of the camera. 
Note:
	 •	 Only	users	whose	user	level	is	allowed	to	control	cameras	or	to	configure	the	settings	can	register	the	pre- set positions. 
     
						

							68
Step 1
Display the "Preset/Auto" window. (☞ Page 67)
Step 2
Enter the preset position number to move the camera 
direction. 
The preset position number can be entered in the 
same manner as of the preset number registration  
(☞ page 67). 
When entering number "000", the camera direction 
will move to the home position. 
Note:
	 •	 It	is	necessary	to	register	the	"Home"	position	by	 configuring the settings of the camera in advance.
Step 3
Move the cursor onto the [Call] button, and then 
press the [SET] button. 
  →  The camera direction will move to the preset posi-
tion corresponding to the entered preset position 
number. 
Step 4
To close the "Preset/Auto" window, press the [SET] 
button after moving the cursor onto the [Cancel] but-
ton or press the [SETUP/ESC] button on the front 
panel. 
    
Move a camera to the preset position
Move the camera to the preset position registered in advance. 
     
						

							69
Step 1
Display the "Preset/Auto" window. (☞ Page 67)
Step 2
Move the cursor onto "Auto mode", and then select 
the desired auto function by rotating the jog dial 
(inside).
The following 8 auto functions can be selected. 
Auto track, auto pan, preset sequence, sort, patrol 1, 
patrol 2, patrol 3, patrol 4
Refer to the operating instructions of the camera for 
information about each auto function. 
Step 3
Move the cursor onto the [Start] button, and then 
press the [SET] button. 
  →  The "Preset/Auto" window will close and the 
selected auto function will start. 
Step 4
To stop the selected auto function, press the [SET] 
button after moving the cursor onto the [Stop] button. 
    Step 5
To close the "Preset/Auto" window, press the [SET] 
button after moving the cursor onto the [Cancel] but-
ton or press the [SETUP/ESC] button on the front 
panel. 
    
Auto functions (Auto panning, etc.)
Activate the auto function of the camera according to the settings of the camera. 
     
						

							70
Step 1
Press the [SUB MENU] button.
  →  The submenu window will be displayed. 
Step 2
Move the cursor onto the [Camera control] button of 
the submenu, and then press the [SET] button.
  →  The menu list will be displayed. Move the cursor 
onto "Camera menu" on the displayed menu list, 
and then press the [SET] button. 
  →  The camera menu will be displayed and the cam-
era setup menu will be displayed on the monitor. 
Note:
	 •	 The	status	bar	will	be	hidden	while	the	camera	 menu panel is being displayed.
    
Operate the setup menu of the camera
To control the camera connected to the recorder, it is necessary in advance to configure the settings of the 
camera function. The settings of the camera function can be configured on the setup menu of the camera. 
It is possible to call the setup menu of the camera from the submenu. The contents of the setup menu and the 
operation procedures vary depending on the model of the camera. Refer to the operating ins\
tructions of the 
camera for further information.
The following are descriptions of how to display the setup menu of the camera and of how\
 to perform the basic 
operation. 
    
Step 3
Operate the setup menu of the camera using the 
camera menu panel. 
To operate the setup menu of the camera, use the fol-
lowing buttons. 
Move the cursor Arrows button (C D A B)
Change parameters Arrows button (A B)
Apply the set value or 
move to the lower level 
menu [SET] button
Move to the higher level 
menu [SETUP/ESC] button
Display the special 
menu Move the cursor onto 
"SPECIAL" on the setup 
menu of the camera, and 
then press the camera 
selection button [2].
Reset the camera Move the cursor onto  "CAMERA RESET" on the 
setup menu of the camera, 
and then press the camera 
selection button [3].
Step 4
To close the setup menu of the camera, press the 
camera selection button [4].
Note:
	 •	 When	the	camera	has	the	refresh	function	 (REFRESH), it is possible to execute the refresh 
function by selecting the [2] button on the camera 
menu panel.
	 •	 The	camera	menu	panel	may	sometimes	remain	 displayed after the setup menu of the camera is 
closed such as when resetting the camera, etc. In 
this case, select the [4] button on the camera 
menu panel. 
	 •	 Only	users	whose	user	level	is	allowed	to	control	 cameras or to configure the settings can configure 
the settings of the camera.