Panasonic Digital Camera Dmc Ls1pp Operating Instructions

Others
91VQT0Q58
∫Recording in simple mode
1 Flash mode (P40)
2 Focus (P31)
3 Picture mode (P35) : Jitter alert (P33)
4 Battery indication (P14)
5 Pictures remaining
6 Built-in memory/card (P20) : Built-in memory
:Card
7 Recording state
8 AF area (P31)
9 Operation for backlight compensation  (P37) 10 Current date and time (
P23)
 This is displayed for about 5 seconds 
when turning the camera on, setting 
the clock and after switching from the 
playback mode to the simple mode.
Zoom (P39)
11 Backlight...

Others
92VQT0Q58
∫In playback
1 Playback mode
2 Number of DPOF prints (P72)
3 Protected picture (P74)
4 Picture size (P65) : In Motion image mode
5 Quality (P66) / : In Motion image mode  (P55)
Simple mode (P35): :ENLARGE
:4qk6q/10 k15cm
: E-MAIL
6 Battery indication (P14)
7 Folder number, file number (P85),  built-in memory/card (P20)
8 Page number/Total pictures
9 Histogram (P29)  It will be displayed when the 
[DISPLAY] button is pressed. 10 Recording information
(Recording mode/Aperture value/...

Others
93VQT0Q58
Cautions for Use
∫Optimal Use of the Camera
When carrying the camera, take care not 
to drop or cause impact to it.
 The lens or the outer case may be  destroyed by the strong shock, and it 
causes a malfunction of the camera.
Keep the camera away from magnetized 
equipment (such as a microwave oven, 
TV, video game equipment, etc.).
 If you use the camera on or near a TV,  pictures may be disrupted due to 
electromagnetic wave radiation.
 Do not use the camera near a cell phone...

Others
94VQT0Q58
∫Card
Do not leave the card in places where 
there is high temperature or direct 
sunlight, or where electromagnetic 
waves or static electricity are easily 
generated.
Do not bend or drop the card. 
 The card may be damaged or the  recorded content may be damaged or 
erased.
 Store the card in the card case or the  storage bag after use and when you store 
or carry the card.
 Do not allow dirt, dust or water to enter the  terminals on the back of the card and do 
not touch the...

Others
95VQT0Q58
Message Display
Confirmation messages or error messages 
will be displayed on the screen in some 
cases.
Major messages are described below as 
examples.
[CURRENT BATTERY TYPE SETTING: 
OXYRIDE] / [CURRENT BATTERY TYPE 
SETTING: ALKALINE/Ni-MH]
If the type of batteries in use is different 
from the one indicated in the message, 
select the type of batteries on [BATTERY 
TYPE] in the [SETUP] menu. (P24)
[THIS MEMORY CARD IS PROTECTED]
Unlock [LOCK] of the Write-Protect switch 
on the SD...

Others
96VQT0Q58
[MEMORY CARD ERROR
FORMAT THIS CARD?]
The format of the card cannot be 
recognized by the camera. Format the card 
again with the camera.
[PLEASE TURN CAMERA OFF AND 
THEN ON AGAIN]
This message appears when the camera 
does not operate properly. Turn the camera 
off and on. If the message persists, contact 
the dealer or your nearest servicenter.
[MEMORY CARD ERROR]
Failed access to the card.
Insert the card again.
[READ ERROR]
Data reading error.
Play it back again.
[WRITE ERROR]
Data...

Others
97VQT0Q58
Troubleshooting
If you put the menu back to the settings at 
the time of purchase, the conditions may be 
improved.
Carry out the [RESET] in the [SETUP] 
menu. (P24)
∫Batteries and the power source
1: The camera is turned off immediately  even when the battery power is full.
The battery indication shows less 
than the actual remaining battery 
power even if new batteries are 
inserted.
 Is [BATTERY TYPE] selected correctly?– Select the item on [BATTERY TYPE]  in the [SETUP] menu. (P24)...

Others
98VQT0Q58
∫LCD monitor
1: The brightness of the screen  becomes dark or bright for a moment.
 This phenomenon appears when pressing the shutter button halfway to 
set the aperture value and does not 
affect the recorded pictures.
2: The screen is too bright or dark.  Adjust the brightness of the screen.
3: Some pixels are inactive or always lit  on the LCD monitor.
 These pixels do not affect the recorded pictures.
This is not a malfunction.
4: Noise appears on the LCD monitor.  In dark...

Others
99VQT0Q58
3: The card is not recognized by the PC.(The built-in memory is recognized.)
 Disconnect the USB connection cable 
and then connect it again with the card 
inserted into the camera.
4: The pictures cannot be printed with  the camera connected to printers.
 Is the printer supporting PictBridge?
– You cannot print pictures with printers  which do not support PictBridge 
(P86).
 Set [USB MODE] to [PictBridge (PTP)].  (P83)
5: Both ends of the picture recorded by  setting the picture size...

Others
100VQT0Q58
Specifications
Digital Camera:Information for your safety 
Camera Effective pixels: 4,000,000 pixels
Image sensor: 1/2.5q CCD, total pixel number 4,230,000 pixels
Primary color filter
Lens: Optical 3k zoom, f l5.8–17.4mm (35mm film camera 
equivalent: 35 – 105 mm)/F2.8 – 5.0
Digital zoom: Max. 4k
Focus: Normal/Macro, 5-area-focusing/3-area-focusing/
1-area-focusing/Spot-focusing
Focus range: 50 cm (1.64 feet) –¶
Macro/Simple: 5 cm (0.16 feet) (Wide)/30 cm (0.98 feet) 
(Tele) – ¶
Shutter...