Panasonic Digital Camera Dmc G85 Owners Manual

							221
9. Using Menu Functions
[Monitor Display]/
[Viewfinder]Brightness, color, or red or blue tint of the Monitor/
viewfinder is adjusted.
1Select the settings by pressing 
3/4, and 
adjust with  2/1 .
•
Adjusting can also be performed by rotating the rear 
dial.
2Press [MENU/SET] to set.
•It will adjust the monitor when the monitor is in use, and 
the viewfinder when the viewfinder is in use.
•Some subjects may appear differently from actuality on 
the monitor. However, this does not affect the recorded 
pictures. s
[Monitor Luminance]
„
 [AUTO]:The brightness is adjusted automatically depending on 
how bright it is around the camera.
 [MODE1]:Make the monitor brighter.
 [MODE2]:Set the monitor to the standard brightness.
 [MODE3]:Make the monitor darker.
•Some subjects may appear differently from actuality on 
the monitor. However, this does not affect the recorded 
pictures.
•The monitor automatically returns to standard brightness 
if no operations are performed for 30 seconds when 
recording in [MODE1]. It will light up brightly again with 
button or touch operation.
•When [AUTO] or [MODE1] is set, the usage time is 
reduced.
•[AUTO] is only available in the Recording Mode.
•The initial setting when using the AC adaptor (optional) is 
[MODE2]. s
>
 [Setup]MENU
…1
…2
…3 
						

							9. Using Menu Functions
222
[Economy]
[Sleep Mode]:The camera is automatically turned off if the camera has 
not been used for the time selected on the setting.
[Sleep Mode(Wi-Fi)]:The camera is automatically turned off if it is not connected 
to a Wi-Fi network and has not been used for 15 minutes 
(approx.).
[Auto LVF/Monitor Off]:The monitor/viewfinder is automatically turned off if the 
camera has not been used for the time selected on the 
setting.
[Power Save LVF Shooting]:
If you enable the automatic viewfinder/monitor 
switching function (P38) and display the “On-monitor 
recording information screen”  (P46) on the monitor, the 
camera is automatically turned off when the camera 
has not been used for the time selected on the setting.
•Press the shutter button halfway or turn the camera off 
and on to cancel [Sleep Mode], [Sleep Mode(Wi-Fi)] and 
[Power Save LVF Shooting].
•To turn the monitor/viewfinder on again, press any button 
or touch the monitor.
•[Economy] does not work in the following cases.–When connecting to a PC or a printer
–When recording or playing back motion pictures–During a slide show–When recording with [ ] ([4K Pre-Burst]) of the 4K 
Photo function
–When using [Multi Exp.]–When using [Time Lapse Shot]
–When using [Stop Motion Animation]  (only when [Auto 
Shooting]  is set)
–When using the HDMI output during recording
•When using the AC adaptor (optional), [Sleep Mode], 
[Sleep Mode(Wi-Fi)] and [Power Save LVF Shooting] are 
disabled.
•When using the AC adaptor (optional), [Auto LVF/Monitor 
Off] is fixed to [5MIN.]. s
[Battery Use Priority][BODY]/[BG] 
P309
>  [Setup]MENU 
						

							223
9. Using Menu Functions
[USB Mode]Sets the communication method when connecting using 
the USB connection cable (supplied).
y
 [Select on connection]:Select this setting to select the USB communication 
system when connecting to another device.
{ [PictBridge(PTP)]:Select this setting when connecting to a printer supporting 
PictBridge.
z [PC]:Select this setting to export images to a connected PC. s
[TV Connection]
[HDMI Mode (Play)]:Set the format for the HDMI output when playing back on 
the HDMI compatible high-definition TV connected with 
this unit using the HDMI micro cable.
[AUTO]:
The output resolution is automatically set based on 
the information from the connected TV.
[4K]:
The progressive method with 2160 available scan 
lines and an output resolution of 3840
k2160 are 
used for output.
[1080p]:
The progressive method with 1080 available scan 
lines is used for output.
[1080i]:
The interlace method with 1080 available scan lines 
is used for output.
[720p]:
The progressive method with 720 available scan 
lines is used for output.
[480p]:
The progressive method with 480 available scan 
lines is used for output.
•This will work only during playback.•If no image appears on the TV with [AUTO], switch the 
setting to a constant setting other than [AUTO] to set a 
format supported by your TV. (Read the operating 
instructions for the TV.) P290
>
 [Setup]MENU 
						

							9. Using Menu Functions
224
[TV Connection]
(continued)
[HDMI Info Display (Rec)]:Sets whether or not to display information when you take 
pictures while monitoring the camera image on a device 
(TV, etc.) connected with an HDMI micro cable.
•When the camera is connected to a TV, lower the volume 
of the TV.P291
[3D Playback]:Set the output method for 3D pictures.
[]:Set when connecting to a 3D compatible television.
[]:
Set when connecting to a television not compatible with 
3D.
Set this when you would like to view pictures in 2D 
(conventional image) on a 3D compatible television.P304
[VIERA Link]:If you select [ON], operations of the camera and the VIERA 
Link compatible equipment connected to the camera with 
an HDMI micro cable are automatically linked, enabling 
you to control the camera with the remote control of the 
VIERA Link compatible equipment.
P293
[Menu Resume]
Stores the location of the last-used menu item for each 
menu.
s
[Menu Background]
Set the background color for the menu screen. s
[Menu Information]Descriptions of menu items or their settings are displayed 
on the menu screen. s
[Language]Set the language displayed on the screen.•If you set a different language by mistake, select [
~] from 
the menu icons to set the desired language. s
[Version Disp.]This enables the firmware versions of the camera and lens 
to be checked.•Press [MENU/SET] on the version display screen to 
display information about the software on the unit. s
[Exposure Comp. Reset]
An exposure value can be reset when the Recording Mode 
is changed or the camera is turned off. s
>
 [Setup]MENU 
						

							225
9. Using Menu Functions
[No.Reset]
Reset the file number of the next recording to 0001.
•The folder number is updated and the file number starts 
from 0001.
•A folder number between 100 and 999 can be assigned.
The folder number should be reset before it reaches 999. 
We recommend formatting the card (P27) after saving the 
data on a PC or elsewhere.
•To reset the folder number to 100, format the card first 
and then use this function to reset the file number.
A reset screen for the folder number will then appear. 
Select [Yes] to reset the folder number. s
[Reset]
The following settings are reset to the default:
–Recording settings (except for [Face Recog.] and 
[Profile Setup])
–Recording settings ([Face Recog.] and [Profile Setup] 
settings)
–Setup/custom settings
•When the setup/custom settings are reset, the following 
settings are also reset.
–The [World Time] setting–The settings of [Travel Date] (departure date, return 
date, location)
–The settings of [Rotate Disp.], [Picture Sort] and [Delete 
Confirmation] in the [Playback] menu
•The folder number and the clock setting are not changed. s
[Reset Wi-Fi Settings]
Reset all settings in the [Wi-Fi] menu to factory default 
settings.
(Excluding [LUMIX CLUB] )•Always reset the camera when disposing or selling it to 
prevent personal information saved within the camera 
from being misused.
•Always reset the camera after making a copy of personal 
information when sending the camera in to be repaired.
s
>
 [Setup]MENU 
						

							9. Using Menu Functions
226
[Pixel Refresh]It will perform optimization of imaging device and image 
processing.•Imaging device and image processing is optimized when 
the camera is purchased. Use this function when bright 
spots that do not exist in the subject get recorded.
•Turn the camera off and on after the pixels are corrected. s
[Sensor Cleaning]
Dust reduction to blow off the debris and dust that have 
affixed to the front of the imaging device is performed.•Dust Reduction Function will operate automatically when 
the camera is turned on, but you can use this function 
when you see dust. s
[Level Gauge Adjust.]
[Adjust.]:Hold the camera in a horizontal position, and press 
[MENU/SET]. The level gauge will be adjusted.
[Level Gauge Value Reset]:Restores the default level gauge setting.
s
[Demo Mode]
You can try focusing, peaking, etc. for the Post Focus 
function 
(P132) by using an example image. s
[Format]
The card is formatted. P27
> [Setup]MENU 
						

							227
9. Using Menu Functions
•The [Playback] menu items below save edited images as new files. If the card is full, new 
images cannot be created. We recommend that you check the card  capacity in advance.
–[RAW Processing]/[4K PHOTO Bulk Saving]/[Light Composition]/[Clear Retouch]/[Text 
Stamp]/[Time Lapse Video]/[Stop Motion Video]/[Resize]/[Croppin g]
•The camera may not play back images recorded on other devices c orrectly, and the functions 
of the camera may not be available for the images.
:[Playback] menu
•[2D/3D Settings]  (P229)•[Slide Show] (P229)•[Playback Mode]  (P231)
•[Location Logging]  (P232)•[RAW Processing] (P233)•[4K PHOTO Bulk Saving]  (P235)
•[Light Composition] (P236)•[Clear Retouch] (P237)•[Title Edit] (P238)
•[Text Stamp] (P239)•[Video Divide]  (P240)•[Time Lapse Video]  (P241)
•[Stop Motion Video]  (P241)•[Resize] (P242)•[Cropping]  (P243)
•[Rotate] (P244)•[Rotate Disp.]  (P244)•[Favorite] (P245)
•[Print Set]  (P246)•[Protect] (P247)•[Face Rec Edit]  (P247)
•[Picture Sort] (P248)•[Delete Confirmation]  (P248) 
						

							9. Using Menu Functions
228
∫How to select an image(s) after selecting [Single] or [Multi] 
•When [Single] and [Multi] are not available, select an image in  the same way as when [Single] 
is selected.
[Single] setting1Press  2/1  to select the picture.2Press [MENU/SET].
•If [Set/Cancel] is displayed at the right bottom of the 
screen, the setting is canceled when [MENU/SET] is 
pressed again.
[Multi] setting
When a screen similar to the one on the right is displayed:
1Press  3/4/ 2/1 to select the picture and then press 
[MENU/SET]  (repeat).
•
The setting is canceled wh en [MENU/SET] is pressed 
again.
2Press  2 to select [OK], and then press [MENU/SET] 
to execute.
When a screen similar to the one on the right is displayed:
Press  3/4 /2 /1 to select the picture, and then press 
[MENU/SET] to set  (repeat).
•
The setting is canceled when [MENU/SET] is pressed again.
6HW
2.
123
456
6HW&DQFHO 
						

							229
9. Using Menu Functions
Playback methods for the 3D pictures can be switched.>  [Playback]  > [2D/3D Settings]
•
This is a menu that is only displayed when 3D playback is possi ble. (P304)
You can play back the pictures you have taken in synchronization with music, and you can 
do this in sequence while leaving a fixed interval between each  of the pictures.
You can also put together a slide show composed of only still p ictures, only motion 
pictures, etc.
We recommend this feature when you view your pictures by connecting the camera to a 
TV.
>  [Playback]  > [Slide Show]
1Select the group to play back by pressing  3/4, and then press [MENU/SET].
•If you select [Video Only], 4K burst files and images recorded  with the Post Focus function 
will also be played back.
•For images recorded with the Post Focus function, only an in-focus representative image 
will be chosen and played back.
•For details on categories, refer to  P231.
2Press  3 to select [Start] and then press [MENU/SET].
∫ Operations during a slide show
[2D/3D Settings]
[Slide Show]
Button 
operationTouch 
operationDescription of  operationButton 
operationTo u c h  
operationDescription of  operation
3Play/Pause4Exit slide show
2Back to previous 
picture1Ahead to next picture
Reduce volume levelIncrease volume 
level
MENU
MENU 
						

							9. Using Menu Functions
230
∫Changing the slide show settings
You can change the settings for slide show playback by selectin g [Effect] or [Setup] on the 
slide show menu screen.
•
Even if you select [Effect], it does not work during slide show s of 4K burst files, images 
recorded with the Post Focus function, or group pictures.
•When playing back the following pictures, the [Duration] settin g is disabled.
–Motion pictures–4K burst files–Images recorded with the Post Focus function
–Panorama pictures–Group Pictures
[Effect]This allows you to select the screen effects when switching fro
m one 
picture to the next.•[AUTO] can be used only when [Category Selection] has been sele cted. 
The pictures are played back with the recommended effects in ea ch 
category.
[Setup] [Duration]
•[Duration] can be set only when [OFF] has been selected 
as the [Effect] setting.
[Repeat] [ON]/[OFF]
[Sound] [AUTO]:
Music is played when the still pictures are played back, 
and audio is played when the motion pictures are played 
back.
[Music]:
Music is played back.
[Audio]:
Audio (only for motion pictures) is played back.
[OFF]:
There will be no sound.